Kali FLYTE UD1A User manual

FLYTE Base User Manual
UD1A Model

1. Product Parts
Part
Description
Qty
Part
Description
Qty
1
Foot
2
9
Handset
1
2
Leg
2
10
ST4.8x16 Self-tapping Screw
2
3
ST4.8x19 Self-tapping Screw
11
11
Control Box
1
4
Fixed Bracket
2
12
Power Cable
1
5
Frame End 1
1
13
Extented Cable
1
6
U Type Frame
2
14
Leveling Feet
4
7
Frame End 2
1
15
M6x16 Machine Screw
8
8 M6x10 Machine Screw 20

2. Installation Tools
Philips Head Screwdriver/ Screwgun
(not provided)
Hex Allen key

3. Assembly Steps
Step 1.
Take one leg (2), one foot (1), one foot washer
and four M6x16 screws (15). Connect leg and
foot with machine screws, attach 2 leveling
feet (14) to the foot. Repeat for the other leg.
Step 2.
Flip the tabletop over. Place the frame on
the underside of table top.
Step 3.
Insert two M6x10 screws (8) into each side
of leg approximately 1/8” in; do not tighten.
Slide leg into frame in the direction of the
arrow, then tighten the four screws.
Repeat for the other leg.

Step 4.
Raise the leg, insert fixed bracket (4) into
end of frame. Attach the bracket to the
leg with two M6x10 screws (8). Repeat on
the other leg.
Step 5.
Assemble frame parts 5,6,7 but do not
tighten. Adjust to the desired width of
the base (space between legs) and
tighten with M6x10 screws (8).
Step 6.
Attach tabletop to the base with four
screws provided: ST4.8x19 (3).

Step 7.
Place the handset (9) in the position
shown (right side, underneath desktop).
Use two screws ST4.8x16 (10) to attach.
Step 8.
Connect all cables from legs, handset, and
power cable to the control box (11).
Extended cable (13) is available. Turn the
desk over and plug in.

4. Handset Controls
LED display
(height display
CM or IN options)
Combination
Setting
- memory key
- unit selection
- sensitivity adjustment
Four memory pre-sets
Up/ down controls

5. Base Settings
Up/ Down control.
Press the Up/ Down button to
reach the desired height. If the
button is pressed briefly, the base
will only raise/ lower by a short
distance.
Memory presets.
You can save up to 4 pre-set desk heights.
Bring the desk to your desired height using Up/
Down controls. Hold M button, the display will
change to “S -” “__” and flash. Press “1” button
to assign the key to this pre-set. Repeat the steps
for keys 1, 2, 3, 4.
To use one of your saved pre-set heights,
simply hit the corresponding key. Desk will raise/
lower to that position. Press any key if you need
to stop the base movement.

Lock/ Unlock base controls.
Press and hols “M” and Up buttons together
for 5 seconds. “Lock” will show on display -
the controls are now locked.
Press and hold “M” and Down buttons together
for 5 seconds. “Lock” on display will change to
the height indicator. The controls are now
unlocked.
Reset controls.
If the display shows RST message, the controls
need to be reset. Press and hold Down until motor
stops, then release the button and press again and
hold for 5 seconds. Initialization mode is now on.
Hold Down key intil you hear the buzzer sound.
Resetting has been finished.
Changing units.
The controls can be set in centimeters or inches.
Hold M button until you see the blinking “S”. Let
go, push M once. You will see the blinking “0” or
“1”. Press Up or Down to select between the two,
“0” for centimeters or “1” for inches. Lock your
selection by hitting M button once.

6. Troubleshooting.
IMPORTANT:
This manual is intended for the installers and for end users.
Improper use of this product may result in property damages or personal injuries.
Do not step on, crawl or lie under the frame. Do not sit or stand on the frame or desk.
Check the appearance of the wire to make sure it’s not damaged.
This product is not suitable for environments with high humidity.
Error code - reason - solution.
E02 - leg height imbalance (over 3/8”) - reset the base
E04 - handset not connected properly - check the wire connections between the
control box and handset
E05 - anti-collision feature - release the buttons, press up or down button again
E08 - tabletop imbalance - reset the base
HOT - overheat protection - power off and wait 20 minutes
E11/E21 - lifting motor 1/2 not connected - check the wire connections to lifting
motor 1/2
E13/E23 - lifting motor not connected - check the wire connection to lifting motor
E16/E26 - Lifting motor 1/2 issues - reset the base
E18/28 - lifting motor overload - reduce the load on the desk