Kallista One P25203-CR User manual

INSTALLATION INSTRUCTIONS
One™ Wall-mount Bridge Kitchen Faucet
1102266_2_A
1 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
P25203-LVP25203-CR

INSTALLATION INSTRUCTIONS
One™ Wall-mount Bridge Kitchen Faucet
1102266_2_A
2 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
THANK YOU FOR CHOOSING KALLISTA
We appreciate your commitment to Kallista quality products. Please take a moment to review this manual be-
fore you install your Kallista product. If you encounter any installation or performance problems, please do not
hesitate to contact us at the phone number listed at the bottom of the page.
BEFORE YOU BEGIN
NOTE: Use two-hole straps or drop-ear ells and screws to secure the water supplies within the wall.
Observe all local plumbing and building codes.
Shut off the main water supply.
Carefully inspect waste and supply tubing for any sign of damage.
Select pipe nipples long enough to protrude through the nished wall.
Do not use petroleum based products on this product.
Kallista reserves the right to make revisions in the design of products without notice, as specied in the 
Price Book.
TOOLS AND MATERIALS
Level
Tape
Measure
Hex
Wrench
Thread
Sealant Square
7/8" Open-End
Box Wrench 2x4 Lumber
Socket Wrench
W/Sockets
Plus:
Pipe Nipples●
Elbows●
Caps●

INSTALLATION INSTRUCTIONS
One™ Wall-mount Bridge Kitchen Faucet
1102266_2_A
3 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
PREPARE THE SITE1.
Escutcheon
2x4
Riser Tube
Pipe
Nipple
Apply
sealant
tape.
8"
(20.3 cm)
Rough-in the Plumbing
IMPORTANT! For exterior wall installations: Ensure proper wall insulation to prevent frozen pipes.
Attach a 2x4 between two studs according to the illustration.
Position the riser tubes 8″ (20.3 cm) apart, then level, and secure the elbows and risers to the 2x4.
Temporarily secure a pipe nipple to each elbow with sealant tape.
Conrm the pipe nipples are perpendicular to the front edge of the vertical 2x4s.
Conrm the Rough-in Plumbing
Hand tighten an escutcheon onto each pipe nipple.
Slide the faucet assembly onto the escutcheons.
Ensure the escutcheons are aligned and level with one another.
Further tighten the escutcheons, if necessary.
Verify the faucet assembly is properly aligned and level. If necessary, make adjustments by repositioning
the elbows, or escutcheons.
Remove the faucet assembly and escutcheons.
Site Checkout
Flush the water lines.
Cap the pipe nipples and check for leaks at the elbows.
Complete the nished wall.

INSTALLATION INSTRUCTIONS
One™ Wall-mount Bridge Kitchen Faucet
1102266_2_A
4 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALL THE ESCUTCHEONS2.
X
Finished Wall
Pipe Nipple
Thread and
tighten the
escutcheons.
Escutcheon
Remove the caps from the pipe nipples.
Reinstall the escutcheons to the pipe nipples.
Measure and note the distance ″X″ from the end of the escutcheons to the nished wall.
Remove the escutcheons.
Remove the pipe nipples and measure their length.
Subtract distance ″X″ from the length of the pipe nipples. Discard the pipe nipples and replace them with 
ones of proper length.
Apply sealant tape to both ends of the pipe nipples, then insert the pipe nipples into the elbows.
IMPORTANT! If you are mounting the escutcheons to an uneven surface (such as tile grout lines), apply a suit-
able sealant to the backside of the escutcheons. Do not use petroleum based sealant.
Thread the escutcheons onto the pipe nipples.
NOTE: Be careful not to damage the nish on the escutcheons when tightening.
Tighten the escutcheons with a 7/8″ deep socket or 7/8″ open-end box wrench.
Ensure the escutcheons are aligned and level with one another. Further tighten the escutcheons, if neces-
sary.

INSTALLATION INSTRUCTIONS
One™ Wall-mount Bridge Kitchen Faucet
1102266_2_A
5 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALL THE FAUCET3.
Not Correct
Setscrew
Aerator Tool
Correct
IMPORTANT! Be careful not to damage the O-rings on the escutcheons during this procedure. The O-rings are
pre-installed in the escutcheons.
Carefully slide the faucet assembly onto the escutcheons.
Using a 1/8″ hex wrench, secure the faucet assembly to the escutcheons with setscrews. The setscrew 
must be ush or recessed.
NOTE: If the setscrews are not ush: Loosen the setscrews, then remove the faucet assembly from the es-
cutcheons. Reinsert the faucet assembly, then retighten the setscrews.
INSTALLATION CHECKOUT4.
Turn both handles clockwise to the OFF position.
Verify that all connections are tight.
Turn on the main water supply.
Check all connections for leaks. Repair as needed.
Turn both handles to the ON position to run water through the faucet. Allow the water to run through the
spout to remove any debris.
Turn both handles to the OFF position.
NOTE: If water ow is restricted: Using the aerator tool (provided), turn the aerator clockwise to remove it from
the spout, remove the debris, then reinstall the aerator. Retain the aerator tool for future use.