Kallista P22100 User manual

Installation Guide
Widespread Lavatory Faucets
P22100, P22130, P22200
P22230, P22500, P22600
P22700, P22800, P22900
P23000
Français, page “Français-1”
Español, página “Español-1”
1008410-2-A

Thank You For Choosing Kallista
We appreciate your commitment to Kallista quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and web site are listed on
the back cover. Thanks again for choosing Kallista.
Tools and Materials
Before You Begin
The illustrations in these instructions may appear different for
your faucet but the installation is the same.
Observe all local plumbing and building codes.
Shut off the main water supply.
Check all threads, connections and O-rings to ensure they are
clean before installing.
Avoid damaging the finish.
Kallista reserves the right to make revisions in the design of
faucets without notice, as specified in the Price Book.
Pipe
Wrench Adjustable Wrench
Plumbers
Putty
Thread
Sealant Sealant
Flat-blade
Screwdriver
1008410-2-A 2 Kallista

1. Install the Spout
Remove the sleeve cap.
Loosen the seal nut by turning it counterclockwise.
Remove the tee by turning the tee nut counterclockwise.
Remove the shank nut and shank washer.
NOTE: Some faucet designs are supplied with a separate
escutcheon. Keep the loose escutcheon on the spout shank.
Make sure the spout gasket is properly seated in the groove on
the bottom of the spout (or escutcheon).
Slide the spout shank through the mounting hole.
Reinstall the shank washer and shank nut.
Wrench tighten the shank nut.
Reinstall the tee. Wrench tighten the tee nut.
Tighten the tee bottom seal nut.
Reinstall the sleeve cap.
Mounting
Surface
Spout Gasket
Spout Shank
Bonnet
Tee
Sleeve Cap
Shank Nut
Shank Washer
Tee Nut
Seal Nut
Kallista 3 1008410-2-A

2. Install the Handle
Turn the bonnet counterclockwise and remove the bonnet from
the valve.
Thread the valve nut down the valve to allow for the thickness of
the mounting surface.
Close the valve (clockwise for hot and counterclockwise for cold).
From below the mounting surface, slide the valve through the
correct (hot = left, cold = right) mounting hole.
Thread the bonnet back onto the valve, making sure the handle
stays in the closed position and is properly aligned.
Tighten the valve nut with a wrench, keeping the handle in the
final installation position.
Repeat the steps above to install the remaining handle assembly.
Bonnet
Valve
Stem
Valve
Nut
Handle
1008410-2-A 4 Kallista

3. Install the Flexible Hose
Insert the pop-up knob assembly into the hole on the top of the
spout and down through the spout.
Thread one end of each flexible hose onto the handle valve
outlets. Do not use thread sealant. Tighten securely with a
wrench. Do not overtighten.
Connect the other end of each flexible hose to the spout supply
tee. Do not use thread sealant. To avoid kinking the hoses, loop
them as shown, if necessary. Tighten securely with a wrench. Do
not overtighten.
Flexible
Hose
Valve
Outlet
Pop-Up Knob
Supply Tee
Kallista 5 1008410-2-A

4. Install the Drain
Remove the protective material from the flange.
Wrap the bottom 2/3 of the flange threads with three layers of
sealant tape.
Apply a ring of plumbers putty or other sealant to the underside
of the flange according to the putty manufacturer’s instructions.
Insert the flange into the fixture drain hole.
Assemble the gasket (tapered side up) and washer to the flange
and partially thread the nut to the flange. Do not fully tighten the
nut at this time.
Install the body washer and drain body with the seal hole facing
the back of the fixture and securely tighten the nut. Use care to
avoid scratching the finish.
Remove any excess putty or sealant.
Insert the stopper into the flange.
Insert the seal into the seal hole on the body.
Seal
Stopper
Lavatory
Screw
Spring
Clip Gasket
NutNut
Link
Rod Seal
Flange
Apply plumbers
putty.
Apply 3 layers of
sealant tape to
bottom 2/3.
Washer
Body Washer
Drain Body
1008410-2-A 6 Kallista

5. Complete the Drain Installation
For regular installations, insert the short end of the rod into the
body seal hole and under the stopper. Secure with the body nut.
Remove and adjust the stopper so it lifts about 3/8″(1 cm) when
opened. To adjust, loosen the stopper nut and shorten or lengthen
the stopper as needed. Tighten the stopper nut.
Apply three layers of thread tape and a small bead of pipe
sealant to the tailpiece threads.
Thread the tailpiece to the body and tighten securely.
Slide one end of the clip onto the rod. Slide the link onto the rod
with the thumbscrew facing the back of the fixture.
Squeeze the other end of the clip, aligning the hole with the rod.
Move the link to the proper position by squeezing the clip and
sliding it along the rod.
Insert the pop-up rod into the hole in the faucet and then into the
hole in the link.
Tighten the thumbscrew onto the link so the pop-up rod knob
extends above the pop-up rod hole.
Body Nut
Stopper
Body
Tailpiece
Seal
Seal Hole
Rod
Apply 3 layers of
sealant tape and a
small bead of pipe
sealant to threads.
Stopper
Nut
Faucet
Rod
Clip
Thumb
Screw
Link
Kallista 7 1008410-2-A

6. Connect the Supplies
Install the water supply shutoff valves according to the
manufacturer’s instructions.
Connect the supply tubes to the valve inlets and supply shutoff
valves. Left is HOT and right is COLD.
Tighten all connections.
7. Installation Checkout
Connect the tailpiece and P-trap (not supplied).
Ensure all connections are watertight.
Remove the aerator assembly by turning it counterclockwise.
Open the drain. Open the main water supply and check for leaks.
Repair as necessary.
Open both hot and cold valves and run water through the spout
for one minute to remove debris. Check for leaks in the flexible
hose connections. Turn the valves off.
Install the aerator assembly.
Shut-off
Valve
Valve Inlet
Supply Tube
Aerator
Spout
1008410-2-A 8 Kallista

Guide d’installation
Robinets de lavabo à large entraxe
Outils et matériels
Merci d’avoir choisi Kallista
Nous apprécions votre engagement envers la qualité Kallista. Veuillez
prendre s’il vous plaît quelques minutes pour lire ce manuel avant de
commencer l’installation. Ne pas hésiter à nous contacter en cas de
problème d’installation ou de performance. Nos numéros de téléphone
et adresse internet sont au verso. Merci encore d’avoir choisi Kallista.
Avant de commencer
Les illustrations de ces instructions peuvent différer de votre
robinet mais l’installation est la même.
Respecter tous les codes de plomberie et de bâtiment locaux.
Couper l’alimentation d’eau principale.
Vérifier tous les filetages, toutes les connexions et les joints
toriques pour s’assurer qu’ils sont propres avant de commencer
l’installation.
Éviter d’endommager la finition.
Kallista se réserve le droit d’apporter des modifications sur le
désign des robinets sans avis préalables, comme spécifié dans le
catalogue des prix.
Clé à
tuyau Clé à molette
Mastic de
plombier
Joint d'étanchéité
pour filetage Mastic
Tournevis à
lame plate
Kallista Français-1 1008410-2-A

1. Installer le bec
Retirer le capuchon.
Desserrer l’écrou de joint en le tournant vers la gauche.
Retirer le T en tournant l’écrou de celui-ci vers la gauche.
Retirer l’écrou et la rondelle du manche.
REMARQUE : Certains désigns de robinet sont fournis avec une
applique séparée. Garder l’applique desserrée sur le manche du bec.
S’assurer que le joint du bec soit proprement reposé dans la
rainure à la base du bec (ou applique).
Glisser le manche du bec à travers l’orifice de montage.
Réinstaller l’écrou et la rondelle du manche.
Serrer l’écrou du manche avec la clé.
Réinstaller le T. Serrer l’écrou du T avec la clé.
Desserrer l’écrou de joint de base du T.
Réinstaller le capuchon.
Surface de
montage
Joint de bec
Manche du bec
Chapeau
T
Capuchon
de manche
Écrou du manche
Rondelle
de manche
Écrou de T
Écrou de joint
1008410-2-A Français-2 Kallista