KAM PAR56 V2 User manual

PAR56 V2
LED parcan lighting effect
LED parcan lighting effect
Modern replacement of a PAR56 light
No bulbs to replace, lightweight and portable
7 channel DMX controllable LED colour mixable spotlights
Sound-to-light mode for non-DMX use
Sound-to-Light operation via built-in mic / Variable mic sensitivity
Preset programs / DMX in and out
RGB configurations and colour mixing / Soft fade colour mixing
Standard LEDs beam angle 25 degrees
DMX control mode, each with 7 channels / Colour can be also set manually
Dip switches for menu control / 151 x 5mm ultra bright LEDs
Low power consumption / Tough metal chassis / Adjustable hanging bracket
Mains fused IEC / Dimensions: 205 x 225 x 210mm (WxHxD) / Weight: 1kg
M A N U A L V E R S I O N 3 . 0
16-01-12
For the latest instruction manual updates and information on the entire Kam range visit:
www.kam.co.uk
Kam products are manufactured by: Lamba plc, Unit 1, Southfields Road, Dunstable, Bedfordshire, United Kingdom LU6 3EJ
Telephone: (+44) (0)1582 690600 • Fax: (+44) (0)1582 690400 • Email: [email protected] • Web: www.lambaplc.com
If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal.
Due to continuous product development, specifications and appearance are subject to change.
© Copyright Lamba plc 2010. E&OE.

Thank you for purchasing this KAM product, we are sure that it will serve you for many years to come.
To optimise the performance of this product, please read these operating instructions carefully to familiarise yourself with the basic
operations of this unit. After you have read the instructions, please retain them for future reference.
This unit has been tested at the factory before being shipped to you.
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. To prevent a fire hazard, do not
expose the unit to any naked flame sources. Unplug this apparatus during lightning storms or if it is unlikely to be used for long
periods of time.
When installing the unit, please ensure you leave enough space around the unit for ventilation. Slots and openings in the unit are
provided for ventilation to ensure reliable operation of the product and to protect it from overheating. To prevent fire hazard, the
openings should never be blocked or covered.
Always handle the power cable by the plug. Never pull out the plug by pulling on the cable. Never touch the power cable when your
hands are wet as this could cause an electric shock. Do not tie a knot in the cable. The power cable should be placed such that it is
not likely to be stepped on. A damaged power cable can cause a fire or give you an electrical shock. Check
the power cord periodicaly, if you ever find that it is damaged, replace it before using the unit again. Contact your retailer for a
replacement.
The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area
where this unit is to be used meets the required written on the unit.
The lightning flash symbol inside a triangle is intended to alert the user to the presence high voltage within the unit’s
enclosure that may be of sufficient power to constitute a risk of electrical shock to persons.
Caution: to prevent the risk of electric shock, do not attempt to open the unit. No user-serviceable parts inside. Refer all
servicing to qualified service personnel.
The exclamation mark inside a triangle is intended to alert the user to the presence of important operating and
maintenance instructions in the literature accompanying the appliance.
Any modification carried out on the unit may invalidate the unit’s warranty.
If applicable, only use the stand, tripod or bracket specified or sold with the apparatus.
Select the installation location of your unit carefully. Avoid placing it in direct sunlight or locations subject to vibration and excessive
dust. Do not use the unit where there are extremes in temperature (below 41ºF / 5ºC or exceeding 95ºF / 35ºC).
Unpacking and safety: Please unpack your new product carefully, your new product should reach you in perfect condition. Please
check that no damage has occurred during transit. If any damage is found, do not operate your unit. Please contact the retailer you
purchased it from immediately. If there is any damage to the mains cable do not use the device. Always disconnect the unit from
the mains supply when carrying out any servicing or cleaning of the unit.
The serial number for this equipment should be located on the rear or underside of the unit. Please make a note of this number as
you will need it for your warranty, it is a good idea to keep a copy of the serial number for your own records.

Rear panel
1. DMX in
2. DMX out
3. DMX address dip switches
4. Mic sensitivity
5. Power mains
6. Sound / auto switch (see dipswitch settings)
Using the preset functions without a DMX controller
Using stand alone settings via dipswitches
Auto / sound mode
Set dipswitch 8 to the on position, then using the sound / auto switch (6) toggle between auto or sound mode
Master / slave
To link several units together using a 3pin DMX lead
Set the first unit as the master
Choose one of the functions from the chart below. i.e. auto mode
Set all other units to slave mode, dipswitch 10 on only.
1=ON 0=OFF X=No function
Function
DIP1
DIP2
DIP3
DIP4
DIP5
DIP6
DIP7
DIP8
DIP9
DIP10
Mode
Red 50﹪
1
0
0
0
0
0
0
0
0
0
Auto(Master)
Red 100﹪
1
1
0
0
0
0
0
0
0
0
Auto(Master)
Green 50﹪
0
0
1
0
0
0
0
0
0
0
Auto(Master)
Green 100﹪
0
0
1
1
0
0
0
0
0
0
Auto(Master)
Blue 50﹪
0
0
0
0
1
0
0
0
0
0
Auto(Master)
Blue 100﹪
0
0
0
0
1
1
0
0
0
0
Auto(Master)
No function
0
0
0
0
0
0
X
0
0
0
No function
Auto/Sound control
0
0
0
0
0
0
0
1
0
0
On/Off/Switch
Fade mode
0
0
0
0
0
0
0
0
1
0
Auto(Master)
With dipswitch 9 on (fade mode) use dipswitch 1-6 to increase fade speed e.g. 9 + 123456 = fast fade
Master/Slave/DMX
0
0
0
0
0
0
0
0
0
1
Auto(Master)
1
2
3
5
4
6

Setting DMX address
To activate the DMX mode
Dipswitch 10 must be in the on position
Use dipswitch 1-9 to set address requires
Each unit uses 7 DMX channels
If all units are to be controlled exactly the same set all units with the same DMX address
If individual control of each unit is required, set all units with its own DMX address
Remember all DMX addresses must be at least 7 channels apart and no DMX channels should cross
For example, unit 1 set to address 1 unit 2 set to address 8 unit 3 set to 15 and so on.
Please note: to operate DMX CH7 Dimmer must have a value.
DMX Control
Channel
Value
Function
CH1
000-255
Red( 0%~100%)
CH2
000-255
Green( 0%~100%)
CH3
000-255
Blue( 0%~100%)
CH4
000-007
Blackout
008-015
Red 100% Green 20%
016-023
Red 100% Green 40%
024-031
Red 100% Green 60%
032-039
Red 100% Green 80%
040-047
Red 100% Green 100%
048-055
Green 100%
056-063
Green 100% Blue 20%
064-071
Green 100% Blue 40%
072-079
Green 100% Blue 60%
080-087
Green 100% Blue 80%
088-095
Green 100% Blue 100%
096-103
Blue 100%
104-111
Red 20% Blue 100%
112-119
Red 40% Blue 100%
120-127
Red 60% Blue 100%
128-135
Red 80% Blue 100%
136-143
Red 100% Blue 100%
144-151
Red 100% Green 25% Blue 100%
152-159
Red 100% Green 50% Blue 100%
160-167
Red 100% Green 75% Blue 100%
168-175
Red 100% Green 100% Blue 100%
176-183
Red 100% Green 100% Blue 25%
184-191
Red 100% Green 100% Blue 50%
192-199
Red 100% Green 100% Blue 75%
200-207
Red 100% Green 100% Blue 100%
208-215
Red 20% Green 100% Blue 100%
216-223
Red 40% Green 100% Blue 100%
224-231
Red 60% Green 100% Blue 100%
232-239
Red 80% Green 100% Blue 100%
240-247
Red 100% Green 100% Blue 100%
248-255
Red 50% Green 50% Blue 50%

CH5
000-255
Strobe (0%~100%)
CH6
000-127
No Function
128-159
Fade mode, control the speed with channel 5
160-223
Auto mode, control the speed with channel 5
224-255
Sound mode
CH7
001-255
Dimmer 0-100%
Specifications
Power supply
90-250 V AC, 50 Hz ~ 60 Hz ~
Power consumption
25 W
Current
0.35A
Sound control
via built-in microphone
DMX-512-connection
3-pin XLR
DMX channels
7
Dimensions
205 x 225 x 210mm (WxHxD)
Weight
1 kg
Maximum ambient temperature T
45℃
Maximum housing temperature T
50℃
Fuse
F1A, 250V
Number of LEDs
5mm x 151pcs