KAMEP Bell J7 User manual

Thank you for purchasing products from KAMEP.
We distinguish ourselves by an unrelenting
commitment to excellence in terms of our reliable
quality, robust design and whole-hearted service.
All items you bought from KAMEP enjoy life-time
warranty service.
Should you have any questions in using our
products, pleasefeel free to contact us by e-mail. A
reply email with solution will reach you within 24
hours.
Your advice and suggestions will be highly appreci-
ated and welcomed.
Email: [email protected]
Whatsapp: [phone]
Website: www.kameplife.com
Warranty Service

1. Meet the doorbell
Camera
PIR Motion Sensor
Microphone
Doorbell Button
LED Indicator
Speaker
Reset Button
Memory Card
Slot
ON/Off Switch
Micro USB Port 
(for battery charging)
Security Screw
Charging
Indicator
Li-ion Battery
Built-in
Doorbell comes with a 4,500mAh rechargeable Li-ion battery.
1

Chime can be powered either by AA batteries or a Micro USB
compatible phone charger
Please mind the battery polarities when installing.
Settings
Volume Control
Select Ringtone
Blue indicator
Red indicator
AA Batteries 
Micro USB Port 
(DC5V power port)
2. Meet the chime (optional)
2

3
3. Charge your doorbell
Prior to the doorbell installation, please charge up your
doorbell for about 8-10 hours till the charging LED
turns BLUE from RED.
LED STATUS INDICATION
Battery charging
Fully charged
Solid red
Solid blue
Compatible charger ( not provided ):
USB compatible phone charger (DC 5V 1A~2A).

4
Switch on power for your doorbell, and you will see
the LED indicator flashes red (once per second). Start
setting up your doorbell following the in-app instruc-
tions.
4. App download
5. Set up doorbell
Search ‘Cloudot’ in the App stores or scan below QR
codes to download the App.
LED Indicator
ON/Off Switch

5
Tips
• Please operate the setup near your Wi-Fi router.
• Make sure your phone is connecting to a 2.4GHz Wi-Fi.
• Make sure the doorbell is turned on, and its indicator
LED is flashing red. If not, press and hold RESET for 5
seconds.
• Ensure the Wi-Fi signal is good, and the Wi-Fi password
is correct.
LED STATUS INDICATION
Device is abnormal.Solid red
Ready for Wi-Fi configuration.
Connecting to Wi-Fi
Device is onlineSolid blue
Live-viewing doorbell cam
Firmware upgrading
Flash blue (once/sec)
Flash blue (twice/sec)
Flash red (once/sec)
Flash red (twice/sec)

Click the SETTING button on the chime, and the chime
will be in pairing mode for 20 seconds, with its red LED
flashing.
6
6. Pair with chime (optional)
Press the doorbell button to send a pairing signal, and
your chime will sound to react, together with its blue LED
flashing. Chime pairing succeeds.
Chime rings &
indicator flashes blue
Settings
Flashing Red

Note:
The indoor chime may NOT be included in the package.
7
Chime settings.
Settings.
Click to enter/quit pairing mode;
Press & hold settings for 5 seconds to restore
factory defaults.
Volume control button.
Click to control volume:
level 1: 110 dB; level 2: 100 dB
level 3: 90 dB; level 4: 80 dB
Ringtone selection.
Click to change ringtone (4 ringtones available).

8
7. Install Your doorbell
Select location for your doorbell.
(OPTIONAL) Install at an angle.
You can purchase the following angled brackets so as
to point your doorbell to a specific view angle.
25 to 50 degree
angle adjustable
8 degree stackable
wedge mount unit
Wedge Mount
(Not included)
Corner Mount
(Not included)
It is suggested to mount the
doorbell at least 4 feet (120
cm) above the ground for
optimal angle of view and best
motion detection performance.
Select a location.

9
Standard installation.

10
8. Tamper Alarm
Anti-theft Tamper Alarm.
You can also enable the anti-theft alarm in doorbell
settings.
Tamper Alarm On
With tamper alarm on, your doorbell detects disassem-
bly by the trigger on its back, and then a 30-second
siren alarm will be triggered. Meantime, video recording
get started, and alarm notification will be pushed to the
owner’s APP account.
Tamper Alarm Off
You can disable the tamper alarm in doorbell settings,
and detach the doorbell without any alarm for battery
recharge or regular maintenance.
Tamper Alarm
Trigger

11
Q1: Is the video doorbell powered by battery?
A1: Yes, there is a Li-ion battery built-in. Thanks to the low
power consumption technology, a full charge lasts for more
than 2-3 months in our lab test environment. (Lab test
condition: 10 events per day, 15 seconds video recording per
event)
Q2: Does it support legacy hardwire power source?
A2: No, it doesn’t. If you need longer battery endurance,
suggest that adding a solar battery charger for your doorbell, if
only there is sunshine in your doorbell location. You can contact
our after-sale service to know where to buy.
Q3: Does it work with existing mechanical chime?
A3: No. But there is a wireless chime optional, which is powered
by AA batteries. You can pair it with your doorbell and got
notified when visitors press your doorbell button.
Q4: How many wireless chimes can be added to the
doorbell?
A4: The doorbell and its chime communicate via radio frequen-
cy. And they support one-to-many and many-to-one commu-
nication.
Q5: Does it support customized Motion Detection Zones.
A5: Yes it does. You can customize the motion detection zone in
the doorbell settings.
Q6: Does the doorbell support cloud storage?
A6: Your doorbell support local video storage by TF card . And
you can also activate the cloud storage service in theApp. There
is a 7-day-free cloud recording trial service.
9. Trouble Shooting