3. ASSEMBLY
1. SAFETY NOTES
- Check the mount for damage prior to and after use.
-Do not continue to use damaged mounts.
- Maximum centered load: 35 kg
- not suitable for outdoors or moist rooms.
- please refer to local mounting instructions (may possibly
-deviate from the examples provided in Section 5 A, B, C)
- use 4 screws for the wall mount
- only use trained technicians to assemble the system
- only mount on suitable walls with the corresponding
-assembly material (not included in the delivery)
- walls, that are too weak or have electrical and water conduits
-or the like are unsuitable. In case of doubt consult a qualified
-technician.
- regularly check that the screws are tight and the conditions of
-the parts and components are in working order.
- Careful and attentive handling is required when adjusting the
-loudspeakers, because the adjustment options can result in
-the pinching or wedging of your hand.
- when using the holder at "events and production sites for
-scenic presentations" BGV C1 applies accordingly.
1.1 Pace each cover jon the plates Duntil it clicks in place.
1.2 Place plates through the slit in wall tube C.
1.2 NOTE: Hold the pieces in such a way that the back of the tube and the cover
1.2 form a line AND the round part of the cover faces forward.
1.3 Now slip on the remaining two covers jinto place until they click.
2Hold both corner plates Bto the drill hole on the wall tube Cand screw it
2on using two hexagon screws M8 x 60 hand safety nuts M8 g.
3Connect support tube Ato the wall tube C.
3.1 To accomplish this, place the plates of the support tube in the slits of
3.1 the wall tubes.
3.2 Place two hexagon screws M8x60 hthrough the corresponding drill holes
3.2 in the corner plates Band the support arm and tighten the safety nuts M8 g.
3.3 To accomplish this, use the two open-end or ring spanners SW13
3.3 (not included with the delivery).
4NOTE: The mounting bolt is placed in one of FOUR possible drill holes
4and is not tighten in the pre-mounted state.
4.1 Please select the desired position of the bolt and then screw it tight to support
4.1 tube (A) To accomplish this, hold the screw head at the top with an Allen
4.1 wrench / hexagon key SW8 and tighten the safety nut M10 between
4.1 the disk using an open-end or ring spanner SW17.
5After the installation of the screws, place the protective caps (e-1x, f-8x)
5on the screws.
6The four U-discs iare used as spacers for the wall mount.
2. PARTS - OVERVIEW
Conduct a visual inspection to ensure that all the parts are
included and are in working order.
UNPACKAGED PARTS: ASupport tube with pre-mounted bolts, BCorner plate 2x, CWall tube, DFastening clip 2x
PARTS BAG: e1x Protective cap M10, f8x Protective caps M8, g4x Safety nuts M8-SW13, h4x Hexagon screws M8 x 60 mm-SW13,
i4x U-disks ø8,4/24 mm, j4x Adjustment caps
Thank you for choosing this product. The instructions provide
directions to all of the important setup and handling steps. We
recommend you keep these instructions for future reference.
24140 Speaker wall mount
- Stable model, suitable for loudspeakers up to a max. of 35 kg
- Equally suited for home, object and public areas
- Suitable for flange bushings - internal diameter 36 mm
- The speaker distance to the wall can be individually adjusted in 4 positions
- The wall mount is largely covered by the loudspeakers
The back wall
of the wall tube
and the cover
are flush
The radius of
the cover
in the front
1. The radiuses
are in the back
2. Back walls
2. are not flush
3. Combination
3. of 1. and 2.
OK! Incorrect!
NOTE:
The Safety Nut M10 is only tighten a bit at delivery.
Select the desired position for the fitting bolt (a selection of 4 options are
available) and tighten the nut as described in 4.1.
