K&S KS 8TKE 52/35 User manual

Kinetic log splitter
Please, read this manual
carefully before use! Owner’s Manual
KS 8TKE 52/35
EN

INTRODUCTION
SAFETY INFORMATION 1
Thank you for your purchase of Könner & Söhnen products. This manual contains a brief description of
safety, use and debugging. More information can be found on the ocial manufacturer’s website in the
support section: ks-power.de/betriebsanleitungen.
You can also go to the support section and download the full version of the manual by scanning the QR
code, or on the website of the ocial importer of Könner & Söhnen products: www.ks-power.de/en.
Manufacturer reserves the right to make alterations into the generators, which may not be reected in this
manual. Pictures and photos of the product may vary from its actual appearance. At the end of this manual,
You may nd contact information which you are free to use in case of any issues occurrence.
All data, specied in this operation manual is the most up to date for the moment of its publishing. The
current list of service centers you can nd at the website of ocial importer: www.ks-power.de/en.
We care about the environment, therefore, we consider it expedient to saveWe care about the environment, therefore, we consider it expedient to save
paper and leave in print a short description of the most important sections.paper and leave in print a short description of the most important sections.
Be sure to read the full version of the manual before
getting started!
Failure to follow the recommendations marked with this
sign may lead to serious injury or death of the operator
or third parties.
Useful information while operating the machine.
ATTENTION – DANGER!
IMPORTANT!
Please, read this manual carefully before use!
WARNING!
PROTECTING YOURSELF AND THOSE AROUND YOU 1.2
This is a high-powered machine, with moving parts
operating with high energy. You must operate the
machine safely. Unsafe operation can create a number
of hazards for you, as well as anyone else in the nearby
area.
WARNING!
Always take the following precautions when using this machine:
• Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people,
their property, and themselves.
• Always wear protective goggles or safety glasses with side shields while using the Log Splitter to protect
your eyes from possible thrown debris.
• Avoid wearing loose clothing or jewelry, which can catch on moving parts.
• We recommend wearing gloves while using the Log Splitter.
• Wear shoes with non-slip treads when using your Log Splitter. Do not use the machine while barefoot or
wearing open toed sandals.
•Wear long pants while operating the Log Splitter.
Safety symbols and description of inscriptions can be found in the full web version.Safety symbols and description of inscriptions can be found in the full web version.
www.ks-power.de/en |1

SAFETY WITH ELECTRIC - POWERED MACHINES 1.3
Never overlook the hazards of electricity.
WARNING!
Always follow these precautions:
• Never open the switch box or motor cover. Never attempt any electrical repairs yourself. If in doubt,
consult a qualified electrician, or contact your local dealer for help or informations.
• Never use an extension cord that is not rated for outdoor use.
• Never operate the Log Splitter if there is an electrical hazard present.
• Never operate the Log Splitter in wet conditions and always store under cover.
• Never operate the Log Splitter with a damaged electrical cord or damaged extension cord.
• Never pull on the electrical cord to move the machine.
• Always grasp the electrical cord plug when unplugging the cord from the outlet; never pull the plug out by
the cord. Make sure your fingers do not touch the metal prongs when plugging or unplugging.
• Never operate the Log Splitter unless the electrical cord is plug
• If you are using an extension cord, keep the connection between the electrical cord and the extension
cord well away from any water.
• Never use an extension cord longer than 25 feet and smaller than 2 mm2in diameter,
the cord will produce a voltage drop that will prevent the motor from supplying full power and may cause
damage to the motor. Use of a smaller diameter extension cord could result in melting of the insulation or
even create a fire.
• Always keep the electrical cord and/or extension cord away from excessive heat, oil, and sharp objects.
Operating this Log Splitter safely is necessary to prevent
or minimize the risk of death or serious injury. Unsafe
operation can create a number of hazards for you.
WARNING!
• Keep bystanders at least 50 feet away from your work area at all times. Stop the motor when another
person or pet approaches.
• Never allow children to operate the Log Splitter.
Always take the following precautions when operating this Log Splitter:
• The machine is designed to split logs. Do not use it for any other purpose.
• Never operate your unit on a slippery, wet, muddy, or icy surface.
• Exercise caution to avoid slipping or falling.
• Never, under any conditions, remove, bend, cut, fit, weld, or otherwise alter standard parts on the Log
Splitter. This includes all shields and guards. Modifications to your machine could cause personal injuries
and property damage and will void your warranty.
• Allow only one person to operate the Log Splitter at any time. This includes placing the log on the beam.
• If the machine should start making an unusual noise or vibration, shut off the Motor, Unplug the Power
Cord, wait five minutes for machine to cool down then inspect for damage. Vibration is generally a warning
of trouble. Check for damaged parts and clean, repair and replace as necessary.
• Never tamper with safety devices. Check their proper operation regularly.
• Before performing any maintenance or inspection procedure on the Log Splitter, shut off the Motor,
unplug the Power Cord and wait five minutes for machine to cool down.
• Never allow people who are unfamiliar with these instructions to use the Log Splitter.
• Never overload or attempt to split logs beyond the recommendations listed in this manual.
• Never operate the machine when under the influence of alcohol, drugs, or medication.
• Use the machine only in daylight.
• Keep all nuts and bolts tight and keep the equipment in good operating condition.
www.ks-power.de/en |2

SPECIFICATIONS 2
Model KS 8TKE 52/35
Voltage 230 V
Frequency 50 Hz
Engine power 2000 W
Force 8 ton
Engine type electric
Engine model KS ECO 2100
Max. Length 520 mm
Max. Diameter 350 mm
Cycle time ~ 2 sek.
Operating position horizontal
Flywheel speed 400 U/min
Cable length 1.7 m
Electric motor winding copper
Wheels 8’’
Gross dimensions (LxWxH) 1270x340x780 mm
Gross weight 130 kg
Protection class IP54M
Connect the mains lead to a standard 230V±10% (50Hz ±1Hz) electrical supply which has under-voltage,
over-voltage and over-current protection devices as well as a residual current device (RCD) with a maximum
residual current rated at 0.03A.
The diameter of the log is not the only factor that deter-
mines how easy it is to split. A small log may be dicult
to split if it has knots or is a particularly hard wood.
NOTICE
KINETIC LOG SPLITTER CONTROLS AND FEATURES 3
9
10
1
5
67
8
2
3
4
1. Safety Level
2.Engagement Handle
3. Belt Guard
4. Splitting Wedge
5. Ram
6. Cradle
7. Frame Stand
8. Handle
9. Belt
10. Flywheel
www.ks-power.de/en |3

OPERATION 4
1. Position your Log Splitter on a flat, dry surface
and chock the Wheels or screw down the Frame
Stand to prevent the Splitter from moving during
use.
2. Make sure the Log Splitter is plugged into a
properly grounded protected outlet.
3. Push the green button (Fig. 1).
STOPPING THE MOTORSTOPPING THE MOTOR
Push the emergency stop or red button to shut the Motor off (Figure 1).
STARTING THE MOTORSTARTING THE MOTOR
Fig. 1
Unplug the Power Cord when not using the Splitter.
NOTE
Switch
Emergency stop
button
Start button
SPLITTING LOGS 5
Fig. 3 Fig. 4
NOTICE
The kinetic log splitter operates differently than a
hydraulic splitter. Not operating the machine properly
will result in damage to the machine.
Fig. 2
All logs should be no longer than rated. Refer to the following photos for the correct and incorrect methods
of splitting logs. Never split a log using an incorrect or unsafe method.
• Do not place your hands on the ends of the log when loading the Log Splitter. This is a very UNSAFE
method and could result in injury to your hands (Figure 3).
• Do not reach or step across the beam while the Log Splitter is running. This is a very UNSAFE method
which could cause personal injury or even death.
• Never attempt to split wood across the grain (Fig.3). The Log Splitter was not designed for cross-grain
splitting. Doing so could damage the Log Splitter and may cause personal injury.
• Make sure both ends of the log you are splitting are cut as square as possible (Fig.4). This will prevent the
log from sliding out of position while under pressure.
Always follow these notices:
• Do not be timid. A rapid movement of the Engagement Handle is necessary for the Rack and Pinion to
engage and disengage fully without damage.
• The Engagement Handle should never be stopped in any location between the fully forward or fully
backward positions.
www.ks-power.de/en |4

4-5 cm
Hands on Sides
of Wood Fig. 5
LUBRICATIONLUBRICATION
RAIL MAINTENANCERAIL MAINTENANCE
Between each use of the LOG SPLITTER, we recommend
removing any debris caught on the Rail or Ram and applying
a rust preventative (Fluid Film or equivalent) to any bare
metal areas on the top of the Rail (Fig. 7). This will assure the
smoothest return action of the Ram.
• Do not hold the Handle in the forward position
when the Ram stops moving forward. Always pull the
Engagement Handle RAPIDLY to the back (Auto-Retract)
position as soon as the Log is split or when the Ram is
at the end of the stroke or when the Ram stops moving
forward due to a tough log.
1. Place the log on the Log Splitter. Grasp the log on the
sides near the middle of the block (Fig. 5). Center the log,
side-to-side, on the rail of the Log Splitter. Do not place
the log tightly to the cutting knife. The recommended
distance from the cutting knife is 4-5 cm.
The engagement Handle must be held fully in the Split
Position against the hard stop when splitting. Failure to
do so may result in kickback of the Handle.
CAUTION!
2. With one hand, actuate and hold the safety lever
towards you, then RAPIDLY actuate the Engagement
Handle fully towards the Motor until it contacts the
hard stop and hold firmly until the Log is split (Fig. 6).
3. IMMEDIATELY AFTER the log is split, actuate and
hold the Engagement Handle to the Auto-Retract
position to allow the Ram to return. If the Ram stops
before the end of the stroke while splitting a tough
log, quickly actuate the Engagement Handle back to
the Auto-Retract position.
Engagement
Handle
Safety lever
If the Ram stops before the end of the stroke while splitting a tough Log, quickly actuate the Engagement
Handle back to the Auto-Retract position. Let the Ram return and allow the Flywheels to gain momentum
for another full power split.
MAINTAINING THE KINETIC LOG SPLITTER 6
Before performing any maintenance procedure or
inspection, stop the electric motor, wait five minutes to
allow all parts to cool. Disconnect the power cord from
the source of Electricity.
WARNING!
All Bearings of your Splitter are sealed units and should
have sufficient lubricant to last the life of your machine
with normal use.
WARNING!
Top of Rail
Fig. 6
www.ks-power.de/en |5

Tools and Supplies needed:
• General Purpose Grease
• Clean Rags
• 13mm Wrench
1. Use a 13mm wrench to remove the Guard Screws that secure the flywheel Guard (Fig 8).
2. Remove the Guard Screws that secure the Flywheel and Belt Guard.
It is important to grease the Rack every 5 hours for
proper operation.
NOTE
Fig. 9
3. Disconnect the return spring.
4. Pull the Rack out and grease the Rack Teeth, top side of the Rack and the Pinion (Fig. 9).
5. Push the Rack back in and reinstall the Return Spring when finished greasing.
6. Reinstall the Guards.
Guard
Screws
flywheel
Guard
Guard
Screws
Belt Guard
Pinion
Rack Teeth
Fig. 8
REGULAR MAINTENANCE CHECKLIST 7
Folgen Sie allen Anweisungen dieser Betriebsanleitung! Die aktuelle Liste der Servicezentren finden Sie auf
der offiziellen Website des autorisierten Importeurs: www.ks-power.de
PROCEDURE Before each use Every 5 hours Every 25 hours
Check General Equipment Condition
Perform Rail Maintenance
Check Belt
Check the condition of the electrical cord.
Grease Rack
Clean Motor Exterior and Cooling Fins
GREASING THE RACKGREASING THE RACK
Between each use of the LOG SPLITTER, we recommend removing any debris caught on the Rail or Ram and
applying a rust preventative (Fluid Film or equivalent) to any bare metal areas on the top of the Rail (Fig. 7).
This will assure the smoothest return action of the Ram.
www.ks-power.de/en |6

Potential faults and troubleshooting methods can be found in the full version of the manual.Potential faults and troubleshooting methods can be found in the full version of the manual.
WARRANTY SERVICE TERMS 8
The international manufacturer warranty is 1 year. The warranty period starts from the date of purchase.
In cases when warranty period is longer than 1 year according to local legislation please contact your local
dealer.TheSellerwhichsellstheproductisresponsibleforgrantingthewarranty.PleasecontacttheSellerfor
warranty. Within the warranty period, if the product fails because of defects in the production process, it will
be exchanged on the same product or repaired.
The warranty card should be kept throughout the warranty period. In case of warranty card loss, a second
one will not be provided. The customer must provide the warranty card and buyer`s check during request
for repair or exchange. Otherwise, the warranty service will not be provided. The warranty card, attached to
the product during sale, should be correctly and fully completed by the retailer and customer, signed and
stamped. In other cases, warranty is not considered as valid.
Provide clean product to the service center. Parts, that must be replaced, are the property of the service
center.
Fig. 9
www.ks-power.de/en |7

CONTACTS
Deutschland:
DIMAX International GmbH
Deutschland, Hauptstr. 134,
51143 Köln,
www.ks-power.de
Ihre BestellungenIhre Bestellungen
[email protected]
Kundendienst, technischeKundendienst, technische
Fragen und UnterstützungFragen und Unterstützung
[email protected]
Garantie, Reparatur undGarantie, Reparatur und
ServiceService
[email protected]
SonstigesSonstiges
[email protected]
Polska:
DIMAX International
Poland Sp.z o.o.
Polen, Warczawska, 306B
05-082 Stare Babice,
www.ks-power.pl
[email protected]
Україна:
ТОВ «Техно Трейд КС», вул.
Електротехнічна 47, 02222,
м. Київ, Україна
www.ks-power.com.ua
[email protected]
Россия:
ТД «Рус Энержи К&С» 129090,
г.Москва, проспект Мира,
д.19, стр.1, эт.1, пом.1,
комн.6б, офис 99В
www.ks-power.ru
[email protected]