Swisher Ls11534 User manual

Read and follow all Safety

Precautions and

Instructions before

operating this equipment.

LOG

SPLITTER

OWNER’S

MANUAL

1602 CORPORATE DRIVE, WARRENSBURG , MISSOURI 64093 PHONE 660-747-8183

FAX 660-747-8650

MODEL NO.

LS622

LS67525

LS928

LS11534

LS12534D

Manufacturing quality lawn care equipment since 1945

Safety

Assembly

Operation

Service and Adjustment

Repair Parts

Made In The

USA

IMPORTANT

swisherinc.com

㻔㻓㻓㻖㻕

Rev. 04-303

2

In the event you have a claim under this warranty, you must return the product to an authorized service

dealer. All transportation charges, damage, or loss incurred during transportation of parts submitted for

replacement or repair under this warranty shall be borne by the purchaser. Should you have any questions

concerning this warranty, please contact us toll-free at 1-800-222-8183. The model number, serial

number, date of purchase, and the name of the authorized Swisher dealer from whom you purchased the

mower will be needed before any warranty claim can be processed.

THIS WARRANTY DO ES NO T APPLY TO ANY INCIDENTAL O R CO NSEQ UENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIO DS

STATED HEREIN FO R ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of

consequential damages or limitations on how long an implied warranty may last, so the above limitations

or exclusions may not apply to you. This warranty gives you specific legal rights and you may have

other rights, which vary from state-to-state. This is a limited warranty as defined by the Magnuson-Moss

Act of 1975.

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: T his product is free from defects in

materials and workmanship for a period of two (2) year from the date of purchase by the original

consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to

materials or workmanship. This warranty is subject to the following limitations and exclusions:

TABLE OF CONTENTS

WARRANT Y………………....….2

SAFET Y..……………………….3-4

TOWING..….……..……………..5

OPERAT ION……………………6-8

MAINT ENANCE.…………………….8-9

DECALS…..………….……………….10

PART S BREAKDOWN…………….11-18

SPECIFICATIONS..…………………23

1) Engine Warranty All engines utilized on our products have a separate warranty extended

to them by the individual engine manufacturer. Any engine service

difficulty is the responsibility of the engine manufacturer and in no

way is Swisher Mower Co., Inc. or its agents responsible for the engine

warranty. The Briggs & Stratton Engine Service Hot-Line is 1-800-

233-3723. T he T ecumseh Engine Service Hot-Line is 1-800-558-5402.

2) Commercial Use T he warranty period for any product used for commercial or rental is

limited to ninety (90) days from the date of original purchase.

3) Limitation T his warranty applies only to products which have been properly

assembled, adjusted, and operated in accordance with the instructions

contained within this manual. This warranty does not apply to any

product of Swisher Mower Co., Inc., that has been subject to alteration,

misuse, abuse, improper assembly or installation, shipping damage, or

to normal wear of product.

4) Exclusions Excluded from this warranty are normal wear, normal adjustments, and

normal maintenance. T he pump, valve, and cylinder each carry separate

manufacture’s warranties. The valve and cylinder both carry a one (1)

year limited warranty. The pump carries a two (2) year limited warranty.

3

Fluid escaping from a very small hole can be almost invisible. Do not check for leaks with your

hand. Escaping fluid under pressure can have sufficient force to penetrate skin, causing serious

personal injury. Leaks can be located by passing a piece of cardboard or wood over the suspected

leak and looking for discoloration. IF injured by escaping fluid, see a doctor at once. Serious

infection or reaction can develop if proper medical treatment is not administered

immediately.

• Split only one log at a time. Never attempt to split two logs on top of each other.

• Do not straddle or reach across the splitting area while operating the splitter.

• Do not step over splitter when the engine is running. You may trip or accidentally

activate the splitting wedge. Walk around to get to the other side.

• Never place hands or feet between log and splitting wedge or between log and ram during

forward or reverse stroke.

• Never attempt to load splitter while splitting wedge is in motion. When loading log

splitter, place hands on the sides of the log, not the ends.

• Only use your hands to operate the control lever. Never use foot, knee, rope or any

extension device.

• Always keep fingers clear of splits that open in log during splitter operation.

• When splitter is in the return mode, keep hands off the machine.

• Only operate splitter on level ground, not on the side of a hill. It could tip or rolling logs,

poor footing, etc. could cause an accident.

• Never operate or allow someone to operate this equipment while under the influence of

alcohol or drugs.

• Always block the wheels to prevent movement while using splitter.

• Never operate your splitter on wet, muddy, or icy surfaces. Safe footing is essential in

preventing accidents.

• Never operate your splitter while it is attached to the tow vehicle.

• Never make adjustments or repairs with the engine running.

• Never attempt to split woods across the grain. Some types of wood may burst or fly out

of your splitter and result in injury.

• Both ends of the log should be cut as squarely as possible to prevent the log from sliding

out of the splitter during operation. Log length should be kept to 24” or less.

4

TOWING SAFETY

• Do not allow persons to ride on splitter. Do not carry any cargo or wood on your

splitter. It may fall off and endanger vehicles that are following you.

• Be sure jack stand is in the travel position and coupling secure. This must also be

retracted so not to interfere while towing. Retract kickstand by removing pin,

rotating up, and replacing pin.

• Never exceed 45 MPH while towing your splitter. Be extra cautious when

traveling over rough terrain, especially over railroad tracks.

• Always be careful while backing your splitter. You could jackknife your log

splitter if not careful.

• Before using splitter, disconnect it from tow vehicle. A log could easily be

pushed forward into the vehicle.

• See tire and wheel specifications for PSI while towing.

• Be aware of the extra length of splitter while turning, parking, crossing

intersections, and in all driving situations.

•

OPERATION INSTRUCTIONS

POSI-LOCK COUPLER

ADJUST COUPLER LOCKING PRESSURE ON BALL BEFORE USE. PLACE HANDLE IN LOCKED

POSITION WITH BALL IN COUPLER. TIGHTEN LOCKNUT AGAINST TENSION SPRING SO THAT

COUPLER IS NOT LOOSE ON BALL. CORRECT ADJUSTMENT WILL ALLOW HANDLE TO BE

RELEASED WITH MODERATE PRESSURE APPLIED TO HANDLE.

TO OPEN, PULL UP ON COUPLER HANDLE AND ROTATE FORWARD. PLACE COUPLER ON BALL

WHEN BALL IS COMPLETELY NESTED IN BALL SOCKET, ROTATE COUPLER HANDLE

BACKWARD UNTIL HANDLE IS IN LOCKED POSITION.

AFTER TOWING FOR 50 MILES, CHECK COUPLER FOR TIGHTNESS ON BALL. ALWAYS CHECK

TIGHTNESS BEFORE TOWING. BE SURE COUPLER HANDLE IS IN LOCKED POSITION.

WARNING:

NEVER EXCEED WEIGHT CAPACITY AND ALWAYS USE SAFETY CHAINS. ALWAYS USE

CORRECT BALL SIZE, MAKING SURE BALL IS COMPLETELY INSERTED INTO COUPLER. LOCK

COUPLER HANDLE SECURELY BEFORE TOWING. ALWAYS CHECK FOR DAMAGES AND

REPLACE IF DAMAGED. AVOID SHARP TURNS AND STEEP VERTICAL ANGLES WHEN TOWING.

5

OPERATION

Intended use: This log splitter is intended and designed to only split wood. NEVER use

for any other purposes. Doing so can cause injury or VOID THE WARRANTY.

ASSEMBLY INSTRUCTIONS

This log splitter has been partially assembled at the factory. Refer to the drawings and part

lists should it become necessary to disassemble the unit for repair or replacement of parts.

Inspect all components for damage.

WARNING: Exercise extreme caution, as parts are very heavy. Sufficient persons or

mechanical handling equipment should be used.

IMPORTANT: This unit is shipped with oil but without gasoline in the engine. After

assembly, see separate Engine Manual for proper fuel and oil recommendations.

1. General Assembly: Remove top, sides and ends of crate. Place crate panels aside

to avoid puncturing tires. Remove tongue assembly from top.

2. Carefully set the beam pre-assembly aside.

3. Attach tongue to tank/mount plates using two bolts and nuts. Be certain hardware

is secure. (See Assembly Figure 1)

4. Remove tank/engine assembly from base of crate and discard banding.

5. Fender Assembly: Remove fenders from box. Mount to fender brackets with 5/16

hardware provided. Make sure fender clears wheel.

6. The cylinder is tied to the base. Remove ties and slide cylinder/wedge forward

aligning clevis at cylinder end to beam. Insert pin and retaining clips, check

component to assure proper assembly. Stand beam pre-assembly vertical and

secure in position. Roll tank/engine assembly into place, aligning pivot holes. Bolt

with provided hardware. Note: Do not over tighten; this is the vertical/horizontal

pivot point.

7. Pivot beam assembly into the horizontal position and lock with pin provided.

8. Hose Assembly: Locate the Pressure Hose, noted by the pipe fittings, and attach it

to the lower fitting on the valve. The remaining hose attaches to the top fitting of

the valve. Secure with provided hose clamp.

9. Check both the horizontal and vertical positions for any “kinks” in the hoses. Note:

Always make sure beam is locked securely into place.

See OPERATING POSITIONS for Horizontal to Vertical Splitting

Assembly Figure 1

Tank/Mount Plates

6

OPERATION

FILLING THE HYDRAULIC RESERVOIR

Fill the hydraulic reservoir with at least five gallons of Dextron III Automatic Transmission fluid or

10W AW hydraulic fluid. After the hydraulic reservoir and the engine crankcase are filled

correctly with their respective oils, start the engine. Remember to set the throttle and turn on the

fuel shut-off valve. The hydraulic pump should prime itself. With the engine running, move the

hydraulic valve lever toward the wedge. This will cause the cylinder to extend and expel air. When

the cylinder is fully extended, retract it. Repeat this procedure several times. An erratic movement

of the cylinder indicates that there is still air in the system. More oil should then be added to bring

the fluid level up to approximately 1” below the fill hole. After adding more oil to fill the tank,

cycle the cylinder again until it has a constant speed indicating that all air has been expelled. Check

the oil level in the reservoir again. Standard models require approx. 6.5 gallons of hydraulic fluid.

(Deluxe models – 9 gallons)

NOTE: If the tank is overfilled, it will tend to expel oil from the breather cap when the cylinder is

retracted.

START UP

WARNING: DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE

ENGINE AND HYDRAULIC RESERVOIR.

See separate Engine Manual for fuel and oil recommendations. Your log splitter has come

equipped with a fuel shut-off valve for towing purposes.

Before starting engine make sure crankcase is filled correctly with oil and the proper fuel has been

used. The engine will only start when the throttle lever and fuel shut-off valve are turned to their

ON positions.

COLD WEATHER START UP

The Cold Weather Clutch enables the engine to be started without having to pull through cold,

thickened hydraulic fluid. Simply pull the handle out and slide into locked position. Start engine,

let it warm up, and release Cold Weather Clutch. After starting, assure that the lever has reengaged.

TOWING

This unit should not be towed on any street, highway, or public road without checking the existing

federal, local, and state laws. Any licensing or modifications such as taillights, etc., need to comply

with existing federal, local, or state vehicle requirements is the sole responsibility of the purchaser.

Obey all regulations when towing on public roads and highways. See also TOWING SAFETY.

Be sure you are using the correct ball hitch size for the hitch coupler on the log splitter (2” ball).

Be sure safety chains are properly connected. Leave enough slack in chains for turning. See

TOWING SAFETY to read warnings about coupling.

Make sure beam attachment is locked in the horizontal position. NEVER tow splitter in the vertical

position.

Turn the fuel shut-off valve OFF to prevent flooding of the engine while traveling.

TOWING AT NIGHT

The requirements for taillights are based on States regulations. Some states allow towing at night

as long as the towed equipment does not visibly impair the tow vehicle taillights. This is based on a

state, to state requirements. The customer is responsible for meeting the states requirements. A

Taillight Kit Accessory (Part No. 7420)is available and recommended for night driving.

If a “Statement of Origin” is required in your state, see your local dealer to receive one.

7

8

Do not operate your splitter in poor mechanical condition or when needing repair. Repair and

replace worn or broken parts immediately.

Periodically tighten nuts, bolts, and hydraulic fittings.

The hydraulic system of your log splitter requires careful inspection, along with the mechanical

parts. Be sure to replace frayed, kinked, or otherwise damaged hydraulic components.

The pressure relief valve on the splitter is preset at the factory. Do not adjust valve. Only a

qualified service technician should perform this adjustment.

If the wedge becomes dull or nicked, it can be removed and sharpened. The wedge is heavy and

may still have sharp edges, wear gloves while handling the wedge.

REPAIR PARTS

Your Swisher Log Splitter has been produced with components designed specifically to this

machine. Although standard springs, hardware, etc. may look similar to parts used on other

machinery, they may in some cases be made of a different construction and/or materials.

9

OD12 – HYDRAULIC FILL PLUG

DECAL

OD09 – DANGER/POSITION LOCK

DECAL

OD08 – OPERATOR INSTRUCTION

DECAL

OD16 – FUEL S HUT OFF DECAL OD07 – COLD WEATHER DECAL

SAFETY DECALS

Replace decals immediately if damaged.

OD22 – POS ITION LOCK DECAL

OD23 – TOW POS ITION DECAL

10

ASSEMBLY DETAIL

LS622, LS67525, LS928, LS11534

MODELS

SEE DETAIL

1

2

3B

4

5

6

7

8

9

10

A

11

16

15

14

13

12

18

17

8

20

25

21 23

24

2627

22

28

29

6

25

39

31

33 3432

35

35 36

30

42

41

40

38

37

43

44

45

46

47

48

49

50

42

16

51 55

18

52

54

53

52

58

57

56

49

6

5

SEE DETAIL

NOT ALL PARTS ARE ON ALL MODELS

57

B

FENDERS ONLY ON

LS11534 MODEL

19

11

190

SERVICE PARTS

Please have Model and Serial Numbers ready when ordering parts.

Color cannot be guaranteed upon service parts.

ITEM NUMBER DESCRIPTION PART NUMBER

1 RETURN HOSE 54" 7290

2 PRESSURE HOSE 48" 7289

3 #12 HOSE CLAMP LS5001

4 HYDRAULIC RESERVOIR 7319

5 1/2-13 X31/2 GR5 BOLT NB577

6 1/2-13 NYLOCK NUT NB281

7 RESERVOIR VENT PLUG 7379

8 3/8-16 X1GR5 BOLT NB604

9 1/2 X31/2 HITCH PIN W/ HAIR PIN NB648

10 SUCTION HOSE 18" 7346

11 #16 HOSE CLAMP LS4999

12 RETURN LINE FITTING 7329

13 FILTER HEAD LS1112

14 FILTER ELEMENT LS1113

15 1/2-13 X11/4 GR5 BOLT NB647

16 3/8-16 2-WAY LOCK NUT NB280

17 TANK BRACE 7352

18 3/8-16 NYLOCK NUT NB182

19 TRAILER JACK/ CENTERING SPACER 7167 /7165

20 HYDRAULIC PUMP -LS622,LS67525 MODEL LS2001H

HYDRAULIC PUMP -LS928,LS11534 MODELS LS2002B

21 1/8 X1/2 #3 WOODRUFF KEY 024002

22 5/16-18 2-WAY LOCK NUT NB558

23 PUMP PULLEY 7306

24 SET SCREW W/ NYLOCK NB312

25 5/16-18 X3/4 GR2 BOLT NB143

26 FENDER BRACKET -RIGHT SIDE -LS11534 ONLY 7417

FENDER BRACKET -LEFT SIDE -LS11534 ONLY 7418

27 FENDER -LS11534 ONLY 7428

28 KICKSTAND 7398

12

On units w ith Throttle

190 Throttle Plate 7104TC

191 Key Switch (Not Shown) KSM

192 Throttle Cable (Not Shown) 7105

193 Throttle Decal (Not Shown) OD58TX

194 Key Switch Decal (Not Shown) OD99

SERVICE PARTS

Please have Model and Serial Numbers ready when ordering parts.

ITEM NUMBER DESCRIPTION PART NUMBER

29 MOTOR BASE /AXLE 7297

30 TIRE /WHEEL 7296

31 COTTER PIN NB633

32 WHEEL DUST COVER 2203DC

33 CASTLE NUT 2203CN

34 WASHER NB184

35 TAPERED BEARING 2203B

36 BEARING SEAL 2203S

37 BELT 644

38 IDLER ARM 6681TK

39 CLUTCH LEVER 7358

40 SPRING 682S

41 3/8-16 JAM NUT NB174

42 HARDENED WASHER NB196

43 3/8-16 X21/2 GR5 BOLT NB619

44 5/16-18 FLANGE NUT NB170

45 IDLER SPRING MOUNT 2046

46 WIRE LINK FOR IDLER SPRING BRS6H

47 SHOULDER BOLT NB220

48 IDLER PULLEY B527

49 WASHER NB272

50 BELT COVER 7321

51 #14 x3/4 SELF-TAPPING SCREW NB161

52 SAFETY CLIP PIN H11

53 TOWING TONGUE 7343

TOWING TONGUE -LS11534 7168

54 TRAVEL LOCK 7441

55 SAFETY CHAIN W/ HOOK 7366

56 2" BALL COUPLER 7365

57 3/8-16 X3GR5 BOLT NB164

58 3/8-16 X31/2 GR5 BOLT NB649

Color cannot be guaranteed upon service parts.

13

ITEM NUMBER DESCRIPTION PART NUMBER

59 CLIP PIN NB642

60 STEEL PIN 7293

61 HYDRAULIC FITTING 7291

62 STATIONARY LINE ASSEMBLY 7288

63 RAM CYLINDER -LS622 MODELS 7284

RAM CYLINDER -LS928&LS67525 MODEL 7354

RAM CYLINDER -LS11534&LS12534DMODEL 7355

64 1/2-13 X3GR5 BOLT NB131

65 SPLITTING WEDGE 7233

66 1/2-13 X21/2 GR5 CARRIAGE BOLT NB643

67 RETURN LINE FITTING 7329

68 1/2-13 JAM 2-WAY LOCK NUT NB121

69 2-WAY PIPE NIPPLE 7292

70 MASTER CHAIN LINK 7424

71 COTTER PIN NB597

72 VALVE INLET FITTING 7387

73 VALVE CONTROL W/ LEVER 7287

74 BEAM WELDMENT 7624

BEAM WELDMENT -LS12534D MODEL 7384

75 1/4 X1CLEVIS PIN NB522

76 1/2-13 NUT NB213Z

77 VALVE LEVER &GRIP 7423/7425

78 THIN GIB PLATE 7388

79 THICK GIB PLATE 7237

80 BOTTOM GIB PLATE 7333

81 LOCK WASHER NB508

81A FLAT WASHER NB555

62

61

64

68

60

70

69

67

66

65

61

74

72

71

73

75

77

79

80

81

78

76

BEAM DETAIL

ALL MODELS

NOT ALL PARTS ARE ON ALL MODELS

59

63

81A

14

ENGINE DETAIL

LS622, LS67525 MODELS

ITEM # DESCRIPTION PART #

89 ENGINE N/A

90 5/16-18 X11/4 GR5 BOLT NB504

91 5/16-18 2-WAY LOCK NUT NB558

92 UPPER SPACER BB105SL

93 ENGINE PULLEY BB105

94 LOWER SPACER BB105S

95 BELLEVILLE WASHER 699

96 7/16-20 X1GR5 BOLT W/ NYLOCK NB452N

106 KEYSTOCK 9031

182 WASHER TR150W

NOTSHOWN WIRING HARNESS -LS12534D MODEL 7416

NOTSHOWN OIL DRAIN VALVE AS122

NOTSHOWN FUEL SHUT OFF VALVE (INLINE) 7414

ITEM # DESCRIPTION PART #

97 ENGINE N/A

98 5/16-18 X21/2 GR5 BOLT NB138

99 5/16-18 2-WAY LOCK NUT NB558

100 5/16-18 X11/4 GR5 BOLT NB504

101 KEYSTOCK 9030

102 SET SCREW W/ NYLOCK NB312

103 ENGINE PULLEY -LS622 7323

104 BELLEVILLE WASHER 699

105 3/8-24 X1BOLT W/ NYLOCK NB238N

89

90

91

94

93

92

182

96

100

98

97

99

101

105

102

104 103

106

15

ENGINE DETAIL

LS928, LS11534, LS12534D MODELS

95

127

113

126

112

110

129

107

124

108

127

110

114

110

107

126

124

109

122

124

128 110

134

130

146

128 128

131

112

117

125

131

128

145

131

149

116

128

147

124

148

115

129

113

129

123

119 133 132

130

121

120 123

135

136

137

138

140

139

142

151

150

144

143

141

See Detail

152 153

154

155

156

157 156 158

159

160

161

166

164

162

165

163

167

168

169

170

169

See Detail

ASSEMBLY DETAIL

MODEL LS12534D

171

NOT ALL PARTS ARE ON ALL MODELS

173

172

16

174

175

176

177

178

179

180

181

ITEM NUMBER DESCRIPTION PART NUMBER

107 3/8-16 X31/2 GR5 BOLT NB649

108 3/8-16 X3GR5 BOLT NB164

109 1/2-13 X31/2 GR5 BOLT NB577

110 1/2-13 X11/4 GR5 BOLT NB647

112 3/8-16 X1GR5 BOLT NB604

113 5/16-18 X1GR5 BOLT NB143

114 5/16-18 X3/4 FLANGE BOLT NB596

115 #14X 3/4 SELF TAPPING SCREW NB161

116 SHOULDER BOLT NB220

117 3/8-16 X21/2 GR5 BOLT NB619

119 3/4-10 X71/2 GR5 BOLT NB655

120 1/4-20 X1GR5 BOLT NB102

121 5/16-18 X4GR5 BOLT NB513

122 SAFETY CLIP PIN H11

123 1/2 X21/2 BALL LOCK PIN NB651

124 WASHER NB272

125 HARDENED WASHER NB196

126 3/8-16 NYLOC NUT NB182

127 1/2-13 NYLOC NUT NB281

128 3/8-16 2WAY LOCK NUT NB280

129 5/16-18 2WAY LOCK NUT NB558

130 5/16-18 NYLOC NUT NB181

131 3/8-16 JAM NUT NB174

132 1/4-20 NYLOC NUT NB180

133 3/4-10 NYLOC NUT NB313

134 SET SCREW W/ NYLOC NB312

135 SAFETY CHAIN W/ HOOK 7366

136 2" BALL COUPLER 7365

137 TONGUE 7168

138 TUBE RECIEVER 7362

139 KICKSTAND 7386

140 KICKSTAND BRACKET 7385

141 HYDRAULIC PUMP LS2002B

142 HYDRAULIC ELBOW 7291

143 PUMP PULLEY 7306

144 MOTOR BASE 7399

145 BELT 32.5 7345

146 IDLER ARM 6681

147 IDLER PULLEY B527

148 CLUTCH LEVER 7358

149 SPRING 682S

150 BOTTOM COVER 7336

151 MOTOR BASE SUPPORT ARM 7375

152 DUST COVER 2203DC

SERVICE PARTS

Please have Model and Serial Numbers ready when ordering parts.

Color cannot be guaranteed upon service parts.

17

ITEM NUMBER DESCRIPTION PART NUMBER

153 COTTER PIN NB633

154 CASTLE NUT 2203CN

155 WASHER NB184

156 TAPERED BEARING 2203B

157 TIRE &WHEEL 7296

158 BEARING SEAL 2203S

159 FENDER 7428

160 DELUXE TANK WELDMENT 7400

161 RESERVOIR VENT PLUG 7379

162 14" SUCTION HOSE 7419

163 #16 HOSE CLAMP LS4999

164 FILTER ELEMENT LS1113

165 FILTER HEAD LS1112

166 FITTING RETURN LINE 7329

167 82" RETURN HOSE 7326

168 90" PRESSURE HOSE 7325

169 #12 HOSE CLAMP LS5001

170 PIVOT 7402

171 TRAILER JACK /CENTERING SPACER 7167 /7165

172 ROPE GUIDE 2046

173 5/16-18 FLANGE NUT NB170

174 KEY SWITCH NUT 9087

175 KEY SWITCH LOCK WASHER 9088

176 8-32 KEP NUT NB201

177 THROTTLE ASSEMBLY 10036

178 THROTTLE KNOB 686K

179 8-32 X1/2 PHIL TRUSS ZP NB197

180 KEY SWITCH ON-OFF, 2PRONG KSM

181 THROTTLE PLATE 10034

NOT SHOWN BEAM LOCK 7439

NOT SHOWN COMPRESSION SPRING 7429

SERVICE PARTS

Please have Model and Serial Numbers ready when ordering parts.

Color cannot be guaranteed upon service parts.

18

19

NOTES:

______________________________________________________________________

20

NOTES:

______________________________________________________________________

Swisher LS11534 User manual

Popular Log Splitter manuals by other brands