Kanga Kare KK1677 User manual

Horizontal Diaper Changing Station
Installation Instructions
KK1677

ADULT INSTALLATION REQUIRED.
TOOLS REQUIRED:
Level(A)
Measuring tape(B)
Power drill with 7/32” , 1/8” and 1/2” masonry bits(C)
Power screwdriver with bull nose phillips bit(D)
Unpack carton and identify all parts.
READ ALL INSTRUCTIONS BEFORE ASSEMBLY OF Diaper Changing Station.
ASSEMBLY INSTRUCTIONS
PART SLIST
A B
CD
•
•
Parts Description Quantity
Hardware for installation:
3” Wood Screws
3” Wood Screws
4
3/4” Finishing Washers
3/4” Finishing Washers
4
3” Machine Screws
3” Machine Screws
2
3/4 ”Flat Washers
3/4”Flat Washers 3/4”Flat Washers
4
Toggle
Toggle
Anchors
Anchors
2
1-1/4 ” Caps
1-1/4”Caps
Door / Wall Plate 1
For Wood Studs: For Use With Toggle Anchors:
4
Door/Wall Plates to be
Mounted away from
Restroom Door

WARNING
WARNING
INSTALLATION
A stud MUST be located and used for at least one side of the diaper changing station.
The diaper changing station is no stronger than the anchors or walls to which they are attached and, therefore,
MUST be firmly secured in order to support the weight they are intended to support.Contact an architect or
building contractor if any questions.
All 4 of these locations MUST be used for safe installation. The lower holes ensure
installation through the metal brackets.
•
•
•
1. Locate wood stud where left side of changing station will be mounted to the wall.
2. Measure up 42'' (107cm) from the floor and mark the wall.This locates the position
for the top left attachment hole.
NOTE: Mark on wall MUST be in center of wood stud.
3. Align hole in top left corner of changing station with mark on wall and hold in place.
4. Using a level and measuring tape, mark the remaining three (3) holes. After marking holes ,
set changing station down on ground.
5. Use a power drill and appropriate bit to drill four (4) holes in the wall. This may require
2 people.
NOTE1: For wood studs:
-If finished wall surface is tile or masonry over wood studs,use
a 7/32” masonry bit for the pilot hole until you hit the wood
stud, then change to 1/8” bit.
-Use wood screws, finishing washers and flat washers (Fig.a).
NOTE2: For use with toggle anchors:
-If finished wall surface has wood studs that are not 16” on center,
has metal studs, or has an underlying surface of concrete block,
6. Align holes in changing station with drilled holes and secure top left corner of
changing station to wall stud using the appropriate screw and washer. Continue
to secure the three (3) remaining corners using the appropriate screws and washers
as described in Note1 or Note2.
use 1/2” bit.
-Use machine screws and flat washers (Fig.b).
Break-Away
Wood Stud Toggle
Anchor
Fig.d
Fig.c
For holes NOT located in a wood stud, toggle anchors Must be used (Fig.c).
See "Using Toggle Anchors" section.
7. Ensure all four (4) screws are tight and snap caps over screw heads.
Using Toggle Anchors:
1.Insert metal end of toggle anchor into 1/2” hole.
2.Slide zip strip down snugly against wall.
3.Snap off break-away pieces of toggle anchor (Fig.d).
5.Ensure all four (4) screws are tight and snap caps over screw heads.
4.Align holes in changing station with toggle anchors and secure top left corner of changing station to
wall using machine screws and flat washers.Continue to secure the three(3) remaining corners
using machine screws and flat washers.

RECOMMENDED BLOCKING:
If the walls do not have studs on center, then additional
blocking is necessary (Fig.e).
Contact an architect or building contractor to make sure the
blocking is adequate and complies with building codes.
OPERATION:
Rotate base downward. Place infant on top of the changing surface.
Use restraint system as described below. After child has been changed,
remove restraint system and rotate base back up against the wall.
USE OF RESTRAINT SYSTEM:
Place child so restraint strap is located at abdomen. Rotate top of buckle upward and
insert strap in buckle. Pull strap through buckle until snug against infant. Rotate top of
buckle downward to lock the strap into place. Slide yellow locking tab over top of buckle
(Fig.f). Reverse steps to loosen strap.
MAINTENANCE AND CLEANING:
Check all hardware and components monthly or as required to ensure hardware is
tight and there are no missing or damaged components. Take unit out of service if
any component is missing or damaged and contact customer service to order
replacement parts. Do not substitute parts. For replacement parts, contact customer
service at 1300652715
Clean by using a damp cloth with mild soap or mild multi-purpose cleaner. Do not use
any strong chemical cleaners or cleaning agents that may be hazardous to children. Fig.f
Locking
Tab
Top Of
Buckle
WARNING
Child should never be left unattended.
Avoid serious injury from falling or sliding out. Always use restraint system.
Adding excessive weight such as parcels, packages, or accessories to the unit or to the bag hooks that exceed the total
weight limit of 50 pounds (22.7 kg) may cause the unit to be unstable or may cause a hazardous unstable condition to
exist.
•
•
•
Related Products :
SKU 781788W
Baby Change Station Bed Liners
SKU: SB001
Sanitary bin
SKU : BBL10
Scented liners Biodegradable
for Sanitary Bins