Kargo Master 40240 User manual

Installation Guide
Kargo Master
Rancho Cordova, CA 95742
800-343-7486
[e-mail]

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 2
Install Instructions
*PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING,
INSTALLING AND USING THIS PRODUCT*
Warning
Always check for wires, fuel tanks and lines, brake lines and other important vehicle functionality
items prior to drilling and installing all products.
Tools Needed
1/2" Socket and Wrench
#2 Phillips Drive
7/16" Socket and Wrench

3/8" Socket and Wrench

11/32" Socket and Wrench

3/32" Allen Wrench

Table of Contents
Parts List ...................................................................................................................................... 3
Hardware List ............................................................................................................................4-5
Main File Holder Assembly ........................................................................................................... 6
Ford Transit Installation ............................................................................................................... 7
Promaster Installation .................................................................................................................. 9
Before You Begin
Be sure to check the back side prior to drilling or screwing anything into the vehicle. If not
positioned correctly, some drills and screws can hit wires and important vehicle parts.

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 3
Install Instructions
Parts
KM9050-802
KM9050-106-R1
KM9050-805
KM9050-104
KM9050-804

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 4
Install Instructions
18-00568

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 5
Install Instructions
18-00567

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 6
Install Instructions
Step 1
Bolt File Support (KM9050-104) into Main File Holder (KM9050-804) using four 10-32 x 1/2" Pan Head
Screws, four #10 Flat washer and four 10-32 Nyloc Nuts.
We recommend to have the washer on the outside
*TIGHTEN
Step 2
Bolt Lid (KM9050-802) to Main File Holder using three 10-32 x 3/8" Pan Head Screws.
*TIGHTEN

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 7
Install Instructions
Installation Instructions for Ford Transit
Step 1
Bolt bottom bracket to main assembly through the rear holes as
shown. Use two 1/4" x 7/8" hex bolt, two 1/4" lock washers and two
1/4" flat washers.
*SNUG TIGHTEN
Step 2
Bolt the front bracket to
the front of the main assembly
using two 1/4" x 7/8" hex bolt,
four 1/4" flat washers and two
1/4" nyloc nuts.
*SNUG TIGHTEN
** We recommend having bracket all the way towards the bottom of
the slots.
Step 3
Place main assembly with mounting brackets into van. Put in between seats snug against the passenger
side. Be sure to have the rear support bracket past the rear of the rib in the floor.
Step 4
Mark the slots in the rear bracket onto the
mat or floor.
On the side of the seat pedestal, mark the
slot in the front bracket.
Remove assembly with brackets

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 8
Install Instructions
Step 5
Remove rear support bracket from main assembly.
Return to van, Place rear support bracket where you
previously marked.
Secure to floor using four 5/16" x 1.25" self tapping
screws.
Step 6
If desired, you can drill a clearance hole for a 1/4" bolt
into seat pedestal where previously marked. Or you can
wait and drill once the main assembly is placed back
into van.
Step 7
Place main assembly with front bracket back into van and bolt to previously installed rear support using
two 1/4" x 7/8" hex bolt, two 1/4" lock washers and two 1/4" flat washers.
*SNUG TIGHTEN
Step 8
If hole is not drilled in seat pedestal mount,
align bracket and do so now.
Bolt front bracket to seat pedestal mount
using a 1/4" x 7/8" hex bolt, two 1/4" flat
washers and one 1/4" nyloc nut.
Step 9
Align and square the driver data file. Go back and TIGHTEN all bolts.
Your installation is now complete.

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 9
Install Instructions
Installation in RAM Promaster
Step 1
Bolt rear bracket to main assembly through the rear holes as shown.
Use two 1/4" x 7/8" hex bolt, two 1/4" lock washers and two 1/4"
flat washers.
*SNUG TIGHTEN
Step 2
Bolt the front bracket to the front of the
main assembly using two 1/4" x 7/8" hex
bolt, four 1/4" flat washers and two 1/4"
nyloc nuts.
*SNUG TIGHTEN
** We recommend having bracket all the way
towards the bottom of the slots.
Step 3
Place main assembly with mounting brackets into van.
Put in between seats. In the bottom bracket, mark the
four slots onto the floor of the van. In the front bracket,
Mark slot onto floor.
Remove main assembly from van.
Step 4
Check under the mat where previous slots were marked.
Be sure to have slots located in a way that it does not
interfere with anything important.
Step 5
Remove rear support bracket from main assembly.
Return to van, Place rear support bracket where you
previously marked.
Secure to floor using four 5/16" x 1.25" self tapping screws.

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 10
Install Instructions
Step 6
Place rest of driver data file back into van.
Bolt to previously installed bottom bracket using 1/4" bolts.
Step 7
Align and tighten all bolts from previous steps.
Bolt front bracket to floor using a 5/16" x 1.25" self tapping screw.
Tighten
Your installation is now complete.