Kasten LS3 Instruction sheet

List of recommended tools:
• Fixed wrench kit
• Socket wrench kit
• Measuring tape 5m
• Spirit level
• Impact tightening tool (optional)
• Extension cord
• Vacuum cleaner for cleaning dust from the holes
• SDS concrete drill with a SDS 8 x 200mm drill bit
• Standard drill with a 7mm drill bit
Recycling: the metal components do not contain toxic
substances harmful to the environment; please recycle
in an appropriate way.
LS3 Kit with chipboard shelves LS3 Kit with steel shelves
Use gloves Avoid contact with
water
Ensure a at
surface
Install the beams in
height according to the
project specications
Do not use
damaged parts
Distribute the
weight evenly
Fasten the storage
system to the oor
Do not climb on the
rack
LS3 longspan shelving
Installation guidelines

LS3 installation guidelines
Carefully follow the assembly instructions listed below
LS3 installation guidelines
Carefully follow the assembly instructions listed below
1
Fit the footplate to the frame using 2 M6x14
screws and 2 M6 self-locking nuts
7
Once lifted, ensure the frame is secured.
13
Depending on the conguration provided,
continue to safely secure all beams following
the previous steps (steps 8 -11).
19
Position the steel shelves on the beams.
2
Using M6x40 bolts (for 50mm upright) or
M6x50 (for 60mm upright) and M6 nuts,
secure the bracing sets to the frame.
See g A for standard congurations.
8
Place the lowest rear beam in the slot
following the conguration provided.
14
Using a tape measure, measure the bay
diagonally ensuring a maximum tolerance of
+/- 3mm. Repeat this step to ensure an even
diagonal measurement both ways.
20
After completing the assembly, a nal
inspection of the system must be carried out
before use.
3
The assembly of this system must be carried
out using professional tools.
To ensure the components are not deformed
by over tightening, please do not exceed a
tightening value of 4.5Nm.
9
at the rst end. Raise the next frame & place
the lowest rear beam in the corresponding
slot following the conguration provided.
15
Using a spirit level, check each frame
vertically ensuring a maximum tolerance of
+/- 1mm.
21
Position the chipboard shelves on the
beams.
4
Assemble all the frames following the
conguration provided.
10
Secure the beam connectors using the safety
locking pins provided.
16
After measuring vertically, ensure the frames
are adjusted if needed. Any adjustments
must be made using the correct levelling
shim for the type of footplate supplied.
22
After completing the assembly, a nal
inspection of the system must be carried out
before use.
5
When raising the frame, ensure the lower
part is secured to avoid accidental slipping.
11
Raise the next assembled frame & repeat
steps 8 & 9. Place the beam in the intended
location and secure with a safety locking pin.
17
When xing the frames to the oor, ensure
the oor is drilled using a SDS concrete drill
and SDS 8mm drill bit.
Only drill 100mm deep.
23
Load Boards must be installed in a visible,
easily accessible position.
Hold load board in position against the
upright and mark through holes from rear for
drill positions.
6
Depending on the size of the frame, it is
possible that you may need more people to
support when lifting.
12
Repeat steps 8-11 to safely secure the
second rear beam.
18
Inspect the assembly before positioning the
shelves.
For steel shelves follow steps 19-20 & 23-24.
For chipboard shelves follow step 21 onwards.
24
Drill the load Boards using a standard drill
and 7mm drill-bit.
Using 2 M6x14 screws and 2 M6 nuts,
secure the Load Board to the frame.
Steel shelves Chipboard shelves

Constructor Finland Oy
Sauvonrinne 12, FI-08500 Lohja P.O.
Box 100, FI-08150 Lohja, Finland
T. [phone]
sales@kasten.
www.kasten.
3000
65
150
750
150
750
150
150
750
85
65
150
750
150
300
85
1500
2000
65
100
750
100
750
150
85
2500
65
150
750
150
750
150
85
400
Figure A - Standard congurations
Important Note:
For working at heights, the appropriate lifting equipment should be used.
The personnel who will carry out the assembly work will observe the H&S provisions.
To prevent accidents, the assembly must be carried out by a competent person, equipped with goggles, overalls,
gloves, protective footwear and helmet.
1912-020_FI(EN)