Kay Home Products Patio-Mate User manual

Patio-Mate®
Owner’s Guide and Assembly Instructions
All Models With 45” Wide Panels

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)2
ASSEMBLY INSTRUCTIONS
7, 8, 9, 10, and 11 Panel x 45” Wide Panel Models
IMPORTANT: Read assembly instructions completely before beginning! Do not attempt to assemble unit if parts are missing.
Safety and Service Instructions:
The Patio-Mate®Screen Room is not designed to support a snow load. Remove the roof in off-season. Do not hang objects
from rafters; rafter assembly is designed to support the roof only.
Rain gutters are required on the house above the Patio-Mate®to prevent damage from excessive water accumulation.
If severe winds or storms are forecast, removal of the roof from your Patio-Mate®is recommended.
Though the roof meets requirements for being flame retardant, keep open flames and flammable materials outside and at a
safe distance from your Patio-Mate®.
Prior to assembly - Tools required for installation:
Step Ladder
1/4" or 3/8" Electric Drill
5/32”, 3/32”, and 3/16” Drill Bits
2' or 4' Construction Level
Hacksaw (with fine tooth blade)
Flat Head Screwdriver
Philips Head Screwdriver
16' Steel Tape Measure
7/16" and 3/8” Open-End, Box-End, or Socket Wrenches
Wood Furring Strips
Note:
To attach your Patio-Mate to a concrete slab, you will need a 1/4" x 1" Tapcon® concrete screw (available at your local
hardware store) for each anchor bracket. You will also need a hardened drill bit large enough to accommodate the selected
Tapcon® screw.
Check the height from your patio deck to the eaves of your house. It is important that this height is at least 91”.
It is strongly recommended that the Patio-Mate be attached to a 1"x3" or 2"x4" weather-treated perimeter furring, as
shown in Figure 1. The furring makes installation easier and more precise on masonry walls, and is an absolute must for
unsupported aluminum and vinyl siding installations for the purpose of strength.
• Do not attempt to assemble the Patio-Mate®under windy conditions.
• Completely open vinyl roof on a clean, flat surface, preferably in direct sunlight to allow folds and ceases to diminish.
(Top surface of the roof should be facing up.)
• We recommend that two persons erect the Patio-Mate®together.
• Remove roof, U-channels, rafter tubes and bag of parts from packing carton, verifying parts lists at the end of this manual.
• You must erect your Patio-Mate on a level base. The recommended base should be concrete, a wood deck or minimally, a
2" x 4" weather-treated wood base, placed directly on and anchored securely to level ground.
Attach foam strip (Item 29) to outer edge of Wood Furring Strips. The foam helps to prevent moisture and bugs from getting
between furring and wall. Attach furring horizontally and vertically to the house frame with foam strip between furring and house
(See Figure 1). This will provide a continuous and sound surface, (i.e. in one plane), on which to attach your Patio-Mate®. If
you are attaching your Patio-Mate®to a flat wall surface the foam strip is not needed.
W H
7 Panel 141” 89”-94”*
8 Panel 187” 89”-94”*
9 Panel 233” 89”-94”*
10 Panel 187” 93”-96”*
11 Panel 233” 93”-96”*
Furring Strip Width and Height
* The height that you choose for the furring strip will determine to which hole on the front of your rafter tubes you will connect
to. The furring strip height should only change (within the range listed) in one-inch increments to correspond with the rafter tube
holes and will provide a proper roof angle. This is very important because an improperly angled roof will result in the unit
collapsing due to the weight of standing water. The higher the furring strip height, the lower the hole you will use on the
front of the Rafter Tubes (Item 8) to secure them to the frame (See Figure 11).
Figure 1

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)3
1. To assemble the roof frame:
A) Critical Step: Inspect the pieces of C-Channel (Item 2,3,4). Notice that the C-channels are marked “L” (Left),
“C” (Center), and “R” (Right). The 7 panel unit does not use any of Item 3.
B) Attach the aluminum ‘C’-channel to the horizontal furring strip. Fasten with the #14 x 1" Screws (S1) provided. Screw is
inserted through hole in Rafter Bracket (Item 6) then through C-channel hole and driven into furring strip, as shown in
Figure 2. ‘C’-channel must be level and centered on horizontal furring strip.
2. To assemble the wall:
A) Attach a 75" U-channel (Item 20) to each vertical furring strip on your home as shown in Figure 3. Check verticality with a
level and pre-drill three 3/16” holes in each channel. Attach each U-channel using three #10 x 1” Screws (S2), provided.
Figure 3
CAUTION:
The screws supplied to fasten the rafter hanger brackets and the U-channel to the house wall are for attachment to solid
types of house sidings and rigid-backed aluminum and vinyl siding. Care should be taken to ensure that the screws are driven
into a solid surface. It may be necessary to obtain longer screws or fur out the house wall as recommended.
Figure 2
7 Panel Patio-Mate®
8 and 10 Panel Patio-Mate®
9 and 11 Panel Patio-Mate®

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)4
2. To assemble the wall (continued):
B) Set packing carton upright and remove wall panel assembly. Save this packing carton for off-season storage of your
Patio-Mate®.
C) Unfold the wall assembly like an accordion (Figure 4) and identify top by riv-nut threaded inserts and wide baffle above
door. Note: The riv-nuts may be covered by white foam pads which must be removed prior to assembly. The
screen-cloth is on outside of frames, indicating outside of wall assembly. Set assembly upright on patio surface and
form a rough rectangle. If you wish to change door location, follow special instructions for door panel relocation at this
time.
D) Align the two wall assembly ends with the vertical U-Channels (Item 20) previously attached to the furring, push the wall
panels into the U-Channels (Item 20) until they are fully inserted and tight against the house.
F) Locate the Threshold(s) (Item 23). The threshold(s) are placed under the doors as shown in Figure 5b. Simply lift panel
assembly, center thresholds under doors, and allow door frame to slip into the channel in the threshold. Check the
rectangle now formed by the panels is square by measuring diagonals (they must be equal).
IMPORTANT:
The patio enclosure door sections must be vertically straight and level to function properly.
Figure 5
E) Drill 5/32" pilot holes sideways through the outside of each U-channel (Item 20) into the wall panel, two per panel edge,
fasten with #10 x 1/2" Screws (S3) provided. See Figure 5a.
Figure 4

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)5
Special Instructions - Door Panel Relocation
If you are assembling the Patio-Mate®for the first time, follow the general assembly steps through 2C. If the Patio-Mate®
is already assembled, remove the roof, disassemble the roof rafters and remove wall assembly from U-Channels (Item
20).
1. One side wall panel has 2 riv-nuts on the top of the frame. If the door is to be moved to either side wall, this panel
must go where the door was originally located. All front wall panels must have 2 riv-nuts in the top of the frame.
Note: The riv-nuts may be covered by white foam pads which must be removed prior to assembly.
2. Decide which screen panel should be replaced by the door panel and remove the Hinge Retainers (Item 15) at the
two top comers of this panel. Simply depress the black square studs and slide the retainers out. See Figure 6.
3. Also, remove the hinge retainers from the right top comer of the door panel to the left of this screen panel and from
the left top comer of the door panel to the right of this screen panel, See Figure 6.
4. Remove the Vinyl Hinges (Item 21) from the left and right sides of this panel by sliding the hinges up and out. Then
set the panel aside.
5. Now, repeat the removal of the four hinge retainers and the two vinyl hinges around the door panel and remove this
panel, moving it to the new location. After removing the door retainers notice that 2 of the door retainers are marked
‘L’ and two are marked ‘R’.
6. The door panel and the displaced screen panel must be attached in their new locations by sliding in their two hinges
and replacing their four hinge retainers. When installing the door retainers remember that 2 of the door retainers are
marked ‘L’ for left side and ‘R’ for right side of panel assembly as viewed from outside of Patio-Mate.
7. Patio-Mate®assembly can then be continued following the general instructions. Start at Step 2D.
Figure 6

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)6
Note:
The Front Stabilizers (Items 11, 12, 13) do not have threaded riv-nut inserts in every hole. The blank holes line up with the
threaded riv-nut inserts installed in panels. Note: The riv-nut inserts may be covered by white foam pads which must be
removed prior to assembly.
IMPORTANT:
The following step varies depending on the door configuration of your Patio-Mate®. Perform only the step that matches your particular unit...
Figure 7
7 8 9 10 11
Number of Item 12 Used 0 1 2 1 2
Number of Panels
G) Inspect the front stabilizers (Items 11, 12, 13), which have threaded riv-nut in-
serts in them. The Left Front Stabilizer (Item 11) has a threaded hole nearest
the left end of the channel. The Right Front Stabilizer (Item 13) has a threaded
hole nearest the right end of the channel. Install stabilizers over the top of the
front wall panels so that the threaded holes are facing the outside of Patio-Mate®,
as shown in Figure 7.
7, 8, 9 Panel Unit With Door In One Of The Front Positions
H) If the door is used in a front panel position the Long Side Stabilizer (Item 14)
is not used. Install Short Side Stabilizers (Item 33) over the tops of the side
wall panels, centered between side wall panels. Drill 5/32" pilot holes through
the stabilizers (into the panels) 2" to 3" from each end of the stabilizer, and
fasten with #10 x 1/2" Screws (S3), provided as shown in Figure 8a. Notice
that one side of stabilizers (Item 33) has 2 grooves and the other has only
one.
IMPORTANT: Install stabilizers so that the side having only one groove faces
the inside of your Patio-Mate®.
Figure 8a
HouseWallFace
Figure 8b
7, 8, 9 Panel Unit With Door In One Of The Side Positions
H) Install the Long Side Stabilizer (Item 14) over the top of the side wall panels
on the side of the Patio-Mate®where the door will be, closer to the front of the
enclosure. Install the 23” Short Side Stabilizer (Item 33) over the top of the
side wall panels, on the side of the Patio-Mate®where the door will be, closer
to the rear of the enclosure. On the other side of the Patio-Mate®Install the
Short Side Stabilizer (Item 33) over the top of the side wall panels, centered
between side wall panels. Drill 5/32" pilot holes through the stabilizers (into
the panels) from the outside of the unit 2" to 3" from each end of each sta-
bilizer, and fasten with #10 x 1/2" Screws (S3), provided as shown in Figure
8b. Notice that one side of stabilizers (Item 14, 33) has 2 grooves and the
other has only one.
IMPORTANT: Install stabilizers so that the side having only one groove faces
the inside of the Patio-Mate®.
2. To assemble the wall (continued):
10, 11 Panel Unit With Door In Any Position
H) Install Long Side Stabilizers (Item 14) over the tops of the side wall panels
where shown in Figure 8c. Drill 5/32" pilot holes through the stabilizers (into
the panels) 2" to 3" from each end of the stabilizers, and fasten with #10 x
1/2" Screws (S3), provided as shown in Figure 8c. Notice that one side of
stabilizers (Item 33) has 2 grooves and the other has only one.
IMPORTANT: Install stabilizers so that the side having only one groove faces
the inside of your Patio-Mate®.
Figure 8c

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)7
3. Rafter Assembly:
7, 8, and 9 Panel Units
A) Assemble Long Rafter (Item 8) to Short Rafter (Item 7)sections
by inserting pinched end of long rafter into non-formed end of
short rafter. Ends must be positioned as shown in Figure 9a.
Pinched joints must be inserted fully. Drill 3/32 hole through to
center of rafter tubes on bottom and fasten using #6 x 3/8 Screw
(S7). Complete the assembly of all rafters. Go to step 3B.
Figure 9a (7, 8, 9 Panel Models Only)
I) The Corner Braces (Item 35) are only provided with the 10 and 11 Panel units
and are not included with the 7, 8, and 9 panel units. With side wall panels
perpendicular to the house, position the Corner Brace (Item 35) over the top
of the stabilizers previously installed as shown in Figure 8d. While holding the
brace in place, use a pencil to mark the hole locations at either end of the brace.
Set the brace aside and drill 5/32" pilot holes through the stabilizers (into the
panels) from the top of the unit. Fasten the brace with #10 x 1/2" Screws
(S3), provided as shown in Figure 8d. Repeat this step for the other corner
brace at the other front corner of your Patio-Mate®.
Figure 8d
2. To assemble the wall (continued):
Note:
I) Step 3A varies depending on the number of panels on your particular unit. Perform only the step 3A that matches the
number of panels on your Patio-Mate®...
10 and 11 Panel Units
A) Assemble Long Rafter (Item 8) to Center Raf-
ter (Item 36) and Short Rafter (Item 7) to Cen-
ter Rafter (Item 36) by inserting pinched end of
long and short rafters into non-formed end of
center rafter. Ends must be positioned as
shown in Figure 9b. Pinched joints must be
inserted fully. Drill 3/32 hole through to center of
rafter tubes on bottom and fasten using #6 x 3/8
Screw (S7). For each rafter insert one Rafter
Clip (Item 37) as shown in Figure 9c. Complete
the assembly of all rafters.
Figure 9b (10, 11 Panel Models Only)
Figure 9c
(10, 11 Panel Models Only)

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)8
Figure 11
C) Cut the remaining 1" foam (Item 29, used in Figure 1) into strips to
fit between the rafters and apply strips to the top of the front wall
panels (See Figure 12).
Figure 10
Figure 12
3. Fasten bent end of rafter to the front stabilizer using 1/ 4”-20 x 1-1/2 machine Screw (S6). Insert screw through Tie-
Down Tab (Item 9), then through Rafter (Item 8), then through Rafter Nest (Item 10), screwing into threaded hole in
front stabilizers (see Figure 11). Be sure to use the correct hole in the front of the rafter tube (Item 8) as determined by
the furring strip height. See Figure 11.
4. Repeat steps 2 and 3 for remaining rafters.
5. Drill a 5/32” diameter hole at each corner of Patio-Mate and fasten a Tie-Down Tab (Item 9), as shown in Figure 11,
with #10 x 1/2 Screw (S3) provided, 2" below top of wall panel. See Figure 11
B) Assemble roof structure:
1. Use a stepladder and a helper and start from the left end of your
Patio-Mate.
2. Attach a rafter assembly to the first rafter hanger with a 1 / 4 - 20 x
3/4" machine screw (S5) and locknut (N1) as shown in (Figure
10).
7,8,9 Panel Units Only 10, 11 Panel Units Only

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)9
4. To Install Roof:
NOTE: Clean screen wall thoroughly before attaching self-adhesive Velcro®tape to ensure proper adhesion
(See Step ‘E’ below).
A) The roof seams are stitched with cotton-wrapped Dacron®thread, which should swell when wet to help prevent any seam
leaks. However, to better ensure that leaks will not occur, you may choose to treat the seams with tent wax or a silicone
spray while the roof is lying flat.
B) Starting at the front edge of the roof, roll up the roof, top surface inward.
C) Using a helper and a stepladder, align the vinyl bulb on the roof with the Horizontal C-Channel (Item 2 or 4). Slide the
roof in the C-channel until the roof is centered over the rafter assembly. See Figure 13.
D) Unroll roof and spread it evenly over the rafter assembly.
E) Cut the strip of self-adhesive Velcro®hook tape (Item 30), provided, into pieces 1-1/2" long.
1. Align 3 Velcro®hook tapes with the Velcro®loop sections sewn to the inside of each gable end and attach to top of
screen wall frame. See Figure 14.
2. Wrap roof Velcro®ribbons around rafter ends See Figure 15.
3. Wrap gable-end front flap around end rafter and attach roof to the rafter using the Velcro®.
F) Cut two 18" lengths of cord (Item 32) from the coil supplied. Tie one end to Tab A, put through Tab B, tie off on Tab C.
Grommet on Tab C should be to outside edge of last roof rafter, to center roof on unit. See Figure 16.
G) Turn roof valance back over roof.
H) Cut remaining cord in half.
Figure 13
Figure 16
Figure 14
Figure 15

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)10
Figure 17
Figure 18
4. To Install Roof (continued):
I) Beginning in the center of the Patio-Mate®, lace roof grommet strip to tie-down tabs as shown in Figure 17. Tie one end
of cord to Tie-Down Tab (Item 9) located at center front of your Patio-Mate®. Begin lacing grommets to the left of center.
Lacing should pull grommets left of center. Repeat step for grommets to the right of center using remaining length of cord.
Lacing in this direction should pull grommets right of center. To achieve the smoothest looking roof vary the tension in the
cords.
J) Locate Side ‘C’ Channel-Left (Item 5) and Side ‘C’ Channel-Right (Item 34). Slide Side ‘C’ Channel-Left (Item 5) onto
bead on roof valence. Center ‘C’ channel on bead. Position ‘C’ channel against furring and fasten to furring using 2 #10 x
1 screws (S2). Repeat step for ‘C’ channel-right (Item 34). See Figure 18.

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)11
5. To install the door:
A) Position Door Track(s) (Item 18) 5” from edge of door frame, on the inside of the Patio-Mate®as shown in Figure 19 with
the overhang in the direction that it is desired to have the door slide.
B) With the top edge of Door Track (Item 18) lined up with top edge of upper stabilizers; mark hole locations on stabilizer. Set
door track aside.
C) Drill 3/16” diameter holes in groove of front stabilizer at marked locations.
D) Screw Door Track (Item 18) to front stabilizer using #12 x ½” screws (S4).
E) With door track level tighten screws (S4) completely.
F) Install the door roller assemblies (Item 31) on door panel using #10 x ½” screws (S3) as shown in Figure 20.
G) Hang the door on the track by putting bottom of door into Threshold (Item 23) and lifting the rollers onto the door track.
H) Repeat steps A-G for other door (If applicable).
Figure 20
Figure 19

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)12
Figure 21
5. To install the door (continued):
I) Open the door approximately half way and place handle (Item 24)
on door approximately 36” from the floor as shown in Figure 21.
Mark the hole location on the door.
J) Remove door handle and drill 5/32” diameter pilot hole in the door.
K) Attach door handle (Item 24) to the door using a #10 x ½” screw
(S3) provided.
L) Repeat Steps I-K for remaining handle (If applicable).
6. To Install Anchor Brackets:
A) Once the wall assembly is square, place an Anchor Bracket
(Item 25) on each panel 2" - 4" from the vinyl hinge between pan-
els. From the inside of the structure lay the anchor bracket, long
side down, on the floor near where it will be installed. Push the
long leg of the anchor bracket under the panel as far as possible.
This should cause the short leg to go over the top edge of the bot-
tom frame member. Mark the location of the hole on the short leg
of anchor bracket on the screen frame. Remove the anchor
bracket and drill a 5/32" diameter hole at the mark. Reinstall the
anchor bracket, attach with #12 x ½ Screw (S4) provided. Repeat
this step on all panels except for the doors. See Figure 22.
B) Attach anchor brackets to deck or patio with appropriate fastener
(not supplied). NOTE: The fastener hole the anchor bracket is de-
signed for a 1/4" diameter screw or bolt.
Figure 22
8. To order parts:
A combination parts/accessories order form is included with your screen house. To order, fill it out and send us the
entire form. A duplicate form will be returned with your parts order. Parts are sold by check, money order, or Visa/
MasterCard. Sorry, no COD orders are accepted.
Parts can also be ordered online at www.kayhomeproducts.com
CAUTION:
Do not leave your Patio-Mate®partially assembled as this may substantially weaken the structure.
IMPORTANT:
Be absolutely certain that the top fabric and rib webs are thoroughly dry before folding. Moisture, if
trapped in folds, will cause rot and mildew.
CAUTION
Though the roof meets requirements for flame being retardant, keep open flames and
flammable materials outside and at a safe distance from your Patio-Mate.
7. To store your Patio-Mate®
• Mild seasonal conditions require only the removal of the vinyl roof for winter preparation. In severe climates, disas-
sembly of the entire unit is recommended by reversing the assembly techniques.
• Clean the roof before storage by using mild detergent and warm water, scrubbing with a medium-bristle brush.
Rinse thoroughly.
• Store your disassembled Patio-Mate in its carton in a dry heated place.

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)13
S1 S2
S3
S7
S4
S5
S6
N1
Item 6
Item 9
Item 10
Item 15
Item 16
Item 19
Item 25
Parts List Quantity
Item Description 7 Panel 8 Panel 9 Panel 10 Panel 11 Panel
1 Roof 1 1 1 1 1
2 C’-Channel - (L)eft 1 1 1 1 1
3 C’-Channel - (C)enter 0 1 2 1 2
4 C’-Channel - (R)ight 1 1 1 1 1
5 Side “C” Channel - (L)eft 1 1 1 1 1
6 Rafter Bracket 10 13 16 13 16
7 Rafter - Short 10 13 16 13 16
8 Rafter - Long 10 13 16 13 16
9 Tie Down Tab 12 15 18 15 18
10 Rafter Nest 10 13 16 13 16
11 Front Stabilizer - Left 1 1 1 1 1
12 Front Stabilizer - Center 0 1 2 1 2
13 Front Stabilizer - Right 1 1 1 1 1
14 Side Stabilizer - Long (68”) 1 1 1 4 4
15 Hinge Retainer - Wall*24 28 28 32 36
16 Hinge Retainer - Door Left*2 2 4 4 4
17 Door Assembly 1 1 2 2 2
18 Door Track 1 1 2 2 2
19 Hinge Retainer - Door Right*2 2 4 4 4
20 Vertical U-Channel 2 2 2 2 2
21 Vinyl Hinge - Wall* 5 6 5 6 7
22 Vinyl Hinge-Door*2 2 4 4 4
23 Threshold 1 1 2 2 2
24 Door Handle 1 1 2 2 2
25 Anchor Brackets 12 14 14 16 18
26 Screen (Replacement)*X X X X X
27 Spline (Replacement)*X X X X X
28 Wall Panel Assembly 6 7 7 8 9
29 1” Self-Adhesive Foam Strip 3 Rolls 4 Rolls 4 Rolls 5 Rolls 5 Rolls
30 Velcro Hook Tape 1 Roll 1 Roll 1 Roll 1 Roll 1 Roll
31 Door Roller Assembly 2 2 4 4 4
32 Cord—Tie Down 1 Roll 1 Roll 1 Roll 1 Roll 1 Roll
33 Side Stabilizer-Short (23”) 2 2 2 0 0
34 Side ’C” Channel - (R)ight 1 1 1 1 1
35 Brace-Corner 0 0 0 2 2
36 Rafter—Center 0 0 0 13 16
37 Rafter Clip 0 0 0 13 16
* Installed on unit
Hardware List
Item Description 7 Panel 8 Panel 9 Panel 10 Panel 11 Panel
S1 #14 x 1” Self-Tapping Screw 10 13 16 13 16
S2 #10 x 1” Self-Tapping Screw 10 10 10 10 10
S3 #10 x 1/2” Self-Tapping Screw 18 18 23 32 32
S4 #12 x 1/2” Self-Tapping Screw 16 18 24 24 26
S5 1/4-20 x 3/4” Machine Screw 10 13 16 13 16
S6 1/4-20 x 1-1/2” Machine Screw 10 13 16 13 16
S7 #6 x 3/8” Self-Tapping Screw 10 13 16 26 32
N1 1/4-20 Lock Nut 10 13 16 13 16
Quantity
Patio-Mate® 7, 8, 9, 10, 11 Panel x 45” Wide Panel
Item 37

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)14
Patio-Mate® 7 Panel x 45” Wide Panel
Assembly Diagram

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)15
Patio-Mate® 8 Panel x 45” Wide Panel
Assembly Diagram

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)16
Patio-Mate® 9 Panel x 45” Wide Panel
Assembly Diagram

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)17
Patio-Mate® 10 Panel x 45” Wide Panel
Assembly Diagram

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)18
Patio-Mate® 11 Panel x 45” Wide Panel
Assembly Diagram

Patio-Mate®(7, 8, 8, 10, and 11 Panel Models with 45” wide Panels)19

SH 115 Rev 103
Kay Home Products
90 McMillen Road
Antioch, IL USA 60002
[phone]
This product manufactured under one or more of the following patents:
United States: 3,952,463 3,996,706 4,561,227
Canada: 1,021,660 1,165,086
Other U.S. and Canadian patents pending