Keithley 7002-RMK-1 User manual

Mdel 7002-RMK-I Fixd Rack Mount ~
The Model 7002-RMK-1 is afixed mck mount kit for the Model 7002. Whh thiskit, the Model 70G2 can be installed in either
a 1Ywi& unive~d or WesternElarnc reck.
The mck tit consis~ of the items listed in thefollowin~ table:
Tabk L
Parrs List
Item
A
B
c
D
E
F
G
hss Pmel
F=tener, captive nut(#10-32)
Hmdle
SCEW;#8-32x 3/W Phil. Rat H-d (hmdle to thess p~e])
Screw; #10-32 x1P Phil. Hat Head (dress p~eI 10ca$e)
Screw; *32 xI/q Phil. Pm H4 (bottom COVerto Cue)
Screw, #l&32 x5W Phil. Tress Head (dess paneIto rack)
Keithley
P& No.
7002-327
FA-148
m-30-1
—
—
—
Qw.
2
4
2
4
4
4
4
RACK PREPARATION consisk of insmlling thefour captive n“t fmteners ~tem B) onto thefio”t mck flmges, 7
em along with the four supplied Tress had sinews Qtem G) secure the inswent ~sembly to the wk. hesefasren-
1. Selea thed~i~d Imation inthe mck ad place one of thetiess pmels fltem A) aztinst the fiottt flange as shown in Figure
.-
1.The WO slottedholes in the dresspmel dicute whex thef~ten~s ~to &imtdled on the rack flmge. Place the dress
pmel on theother tiont mk flmge to loate the other two mottntin~holes.
2. Using Flgwe 2~a~qide, instil the four fmkners ~tem B) onto thefront mck flmges.
CHASSE ASSE~LY P~PARA~ON consists of mounting the hmdles ~tem C) md dresspmels to theinsrmment.Refer
to FID- 3for the fo~oting steps.
3.
4,
5.
6.
Amch thehmdles to the tiss paels with thefour flathad SCKWS(Item D).
The dwomtive stips mustkraoved inofir to amch thedresspmels to the im~ment chmsis. To remove astrip,place
atin bladd tilfe &m&n theSrnpmd thechmsis md p~ the Srnpaway tim tie insmment. Rettin thedecomtive strips
for fttwe W.
Mount the d~s pmels to the insmment chmsis with thesttpplid sinews ~tem E).
Remove the feet ti the bttom of the insmment md ~tin the feet (md tbe screws) for future use. Secu~ the bottom
wver to the cksis using the four supplied smws @tern~.
CA~ON
To prevent dmge to tfte -merit, use tie mppfied &32 xl/& sinews ~tem ~to secure
tie kttom ~ver to the ctii.
PA-594
Rev. A/ 4-93

C~SSIS ASSE~LY ~STALLATION consists of insening the chassis msembly into the prepared space in the mck and
securing it with the suppfid screws @ternG).
7. kping thechassis assembly by the hadles, insen it into the prepaed space in themck
8. Mount thefront of tbe chmsis assembly to the mck using the four screws (Item G).
Fi@re 1.
hcazin: Mowting Holes
Fi@re 2.
Fastemr Imrallation

Fi@re 3.
Dress Panel Installation