Esi Kata ex2-fms User manual

installation instructions

Kata™EX2-FMS

Model# KATAEX2-DC-FMS-___

Model# KATAEX2-GM-FMS-___

___ = SLV, BLK or WHT

dual xed+motion+slider monitor arm

Page 2

KataEX2-FMS Components and tools

Please review these instructions before beginning the installation. Use the illustrations below to check that all the components needed for your

installation were provided with your order. Do not discard the packaging until the product works to your satisfaction.

Components and tools

Additional tools required

• Phillips screwdriver

Caution

• Hand tighten screws only. Do not use power tools.

clamp or grommet mounting:

dual Allen key (1)

2mm and 4mm

monitor arm assemblies (2)

VESA mount

assemblies (2)

connection

sleeve (1)

VESA plate screws (8) set screws (6)

decorative covers (set of 4)

cable clip (1) cable clip (1)

M4x10 M4x15

set screws (2)

M4x9

clamp mounting only: grommet mounting only:

grommet base

assembly (1)

clamp base

assembly (1)

base

cover (1)

grommet bar (1)

grommet knob (1)

base

cover (1)

Page 3

KataEX2-FMS Assembly

0.5" – 2.1" 0.5" – 1.5"

clamp to

worksurface

ﬁt base cover

over base

ﬂush

against

clamp

gap

Follow either step #1a for clamp mounting or step #1b for grommet mounting. All other steps apply to both mounting methods.

Step #1a: attach base assembly to worksurface — clamp mounting

The thickness of the worksurface must be between 0.5" and 2.1". To mount the clamp ﬂush against

the worksurface, the thickness must be no more than 1.5".

• Loosen the clamp suciently to be able to slide it easily onto the worksurface.

• Clamp the assembly to the worksurface in the desired position. Be sure to tighten the clamp securely.

• Place the base cover onto the mounting post and ﬁt the cover over the base.

Step #1b: attach base assembly to worksurface — grommet mounting

Maximum thickness of the worksurface for grommet mounting is 1.7".

• Place the base assembly over the grommet hole with the bolt centered.

• Insert the grommet bar onto the grommet bolt and then screw on the grommet knob. Tighten the grommet knob securely to hold the base assembly in position.

• Place the base cover onto the mounting post and ﬁt the cover over the base.

maximum thickness = 1.7"

center bolt in grommet hole

grommet base assembly

tighten grommet knob to secure

grommet bar

ﬁt base cover

over base

Page 4

KataEX2-FMS Assembly

Step #2: assemble slider mounts

IMPORTANT: When assembling the slider mounts, the groove on the slider bars must be at the bottom.

• Slide the VESA mount assembly onto the slider bar. Center the assembly on the slider bar.

• Install the M4x9 set screw into the bottom of the VESA mount assembly. Use the 2mm Allen key to tighten the set screw to hold the assembly in place. Be sure the

screw tip ﬁts into the groove on the slider bar.

— After the monitor has been installed, the VESA mount can be moved anywhere along the slider bar by loosening the locking screw no more than one full turn, so that

it stays inside the groove. Be sure to re-tighten the screw to secure the monitor in the desired position.

slider bar

VESA mount

assembly

2mm

Allen key

set screw

M4x9

groove

Step #3: install connection sleeve onto post

• Remove the locking ring from the connection sleeve. Rotate the locking ring counterclockwise to unlock it and

then lift it o.

• Slide the connection sleeve onto the post, usually with the screw toward the rear. With the sleeve at the desired

height, tighten the screw using the 4mm Allen key.

— If necessary, the height of the connection sleeve may be adjusted after the monitors have been installed.

CAUTION: Be sure to have an assistant support the weight of the monitors and monitor arms before loosening

the the screw on the connection sleeve. connection

sleeve

to unlock,

turn locking ring

counterclockwise

lift o

4mm

Allen key

Page 5

KataEX2-FMS Assembly

Step #5: secure monitor arm assemblies

• Carefully cut the decorative covers to remove them from the set. Slide the covers into the unused slots on

the connection sleeve.

• Lock the monitor arm assemblies to the connection sleeve with the locking ring. Rotate the locking ring

clockwise to secure it.

Step #4: install monitor arm assemblies

• Monitor arm assemblies are installed by ﬁtting the tabs on the end of the arm stems into slots on the connection sleeve, as shown in the top left illustration below.

— Typically, the arm stems are installed on opposite sides of the connection sleeve, at a 180° angle, with two empy slots between the arm stems.

— To project the monitors closer to the user, the arm stems may be installed at a 135° angle (one empty slot between arm stems) or a 90° angle (no empty slots

between arm stems). However, the ﬁxed-motion arm combination already provides for a large projection; the dierence among the angles is rarely signiﬁcant.

• Install the monitor arm assemblies into the slots on the connection sleeve, with the arm stems at the angle you have chosen.

decorative covers

turn locking ring

clockwise to lock

90°

arm stem

connection

sleeve

135°

180°

tabs

arm stem

slots

Page 6

KataEX2-FMS Assembly

Step #6: attach VESA plates to monitors

• Remove each VESA plate from its VESA mount by (1) pushing forward the tab at the top and (2) lifting upward.

—TIP: Practice re-installing the VESA plate before attaching it to the monitor. This will make step #7 easier.

• Place the monitor face down on a ﬂat surface. Align the VESA plate holes with the holes on the back of the monitor. Attach the VESA plate using the four VESA plate

screws provided.

— There are two sets of four holes on the VESA plates. One set has holes 3.9" (100mm) apart, the other set has holes 3" (75mm) apart. Use the set that matches the

holes on the rear of the monitor.

Step #7: attach monitors to VESA mounts

• Slide the VESA plate (with monitor attached) back onto the VESA mount.

— Make sure the VESA plate clicks securely in place.

• OPTIONAL: Secure the VESA plate to the VESA mount using one of the M4x15 set screws, as shown below. Tilt the monitor upward for access to install the set screw.

attach

monitor

VESA

mount

VESA

plate

2mm Allen key

tilt up

VESA locking screw

M4x15

lift o VESA plate

VESA plate screw

VESA

plate monitor

(face down)

top

3.9"

(100mm)

(75mm)

push tab forward

Page 7

slide out

ﬁxed arm

arm stem

slide up

motion arm

KataEX2-FMS Assembly

Step #8: remove cable management covers

• To remove the cover from the motion arms, slide the cable cover

upward.

• To remove the cover from the ﬁxed arms and arm stems, slide the

cable cover out.

Step #9: install lockout set screws, if desired

Default rotation of the ﬁxed arms and motion arms is 360°. Installation of a lockout set screw limits rotation to 180°.

• To lockout rotation of the ﬁxed or motion arms, install an M4x15 set screw in the underside of the arm stem. Tighten the screw, then back it o one turn.

— Installing a set screw in the front hole allows 180° rotation to the right only. A set screw in the rear hole allows 180° rotation to the left only.

— In the example below, to prevent the ﬁxed arms from rotating to the rear (a left rotation with the left arm and a right rotation with the right arm),

install a set screw in the front hole on the left arm stem and the rear hole on the right. The motion arms are allowed their full 360° of rotation.

• The ﬁxed arm or motion arm must be in its allowed range of rotation when installing the lockout set screw.

front

rear

set screw

M4x15

2mm

Allen key

front

rear

180°

360°

monitors

not shown

Page 8

KataEX2-FMS Assembly

Step #10: organize cables and cords

• Capture the cables and cords with the cable covers. Slide the cable covers as shown to attach them to the monitor arms.

• Snap the cable clips onto the post and into the recessed groove above the base.

• Route the monitor cables and power cords toward the rear by slipping the cords into the opening on the cable clips.

capture

cables

with clips

snap on

cable clips

install covers over cables

slide in

slide

down

Page 9

KataEX2-FMS Assembly

Step #11: make any necessary adjustments

There are six possible ways to change the position of the monitors to maximize the eciency and comfort of the working environment:

1. Monitor position on slider

— To move the monitor from side-to-side, use the 2mm end of the dual Allen key to loosen the set screw (M4x9) on the bottom of the VESA mount assembly, then slide

the monitor along the slider bar. Do not loosen the set screw more than one full turn — the tip of the set screw must remain inside the groove on the slider bar so

that the mount assembly cannot slide o the ends. Re-tighten the set screw when the monitor is positioned where desired.

2. Monitor tilt

— Use the 4mm end of the dual Allen key to loosen the screw on the side of the VESA mount to change monitor tilt angle. Tighten the screw to hold the angle.

3. Monitor swivel

— Use the 4mm end of the dual Allen key to adjust the underside screw behind the VESA mount for the desired ease of monitor rotation.

4. Motion arm weight

— Use the 4mm end of the dual Allen key to adjust the screw at the end of the motion arm for the appropriate monitor weight. When adjusted properly, the monitor

weight is balanced, making it easy to raise or lower the monitor.

5. Motion arm swivel

— Use the 4mm end of the dual Allen key to adjust the screw in the underside of the ﬁxed arm for the desired ease of motion arm rotation.

6. Fixed arm swivel adjustment

— Use the 4mm end of the dual Allen key to adjust the underside screw at the end of the arm stem for the desired ease of ﬁxed arm rotation.

behind

slider

monitors

not shown

Page 10

Notes

LIMITED WARRANTY

ESI warrants this product to be free from defects in manufacturing for a period of 15 years from the date of original purchase. This warranty extends only to the original purchaser, and does not apply

if the product has been damaged or fails to function properly as a result of misuse, abuse, modiﬁcation, alteration, or improper cleaning or maintenance. This warranty does not apply to damage

in shipment caused by carriers, damage caused during installation, normal wear and tear, or excessive use (meaning consistent use in excess of an eight hour shift). ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL RETAIL PURCHASE. ESI’s sole obligation under this warranty

or any implied warranty, and the purchaser’s sole remedy, is limited to the repair or replacement, at ESI’s option, of the product or any defective part. Costs (such as installation, labor fees or express

shipping) incurred due to replacement of products are not covered under warranty. IN NO EVENT SHALL FELLOWES, ITS AFFILIATES, SUBSIDIARIES, RELATED ENTITIES OR THEIR RESPECTIVE OFFICERS,

DIRECTORS, OR EMPLOYEES, BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, EXEMPLARY, OR SPECIAL DAMAGES.

To make a warranty claim, contact ESI at 800-833-3746 or [email protected]. You must provide proof of purchase, such as the original purchase order number.

The duration, terms and conditions of this warranty are valid worldwide, except where dierent limitations, restrictions or conditions may be required by local law.