Kelvinator KL14TT2 User manual

INSTRUCTION MANUAL
TWIN TUB WASHING MACHINE
MODEL:KL14TT2
Please keep this manual for operation and maintenance of this washing machine.

4
4
5
7
8
6
6
6
6
6
9
2
3
2
2
2
1
1
1
3
3
Name Of Parts
Introduction Of Control Panel
Washing Method
Rinsing Method
Spinning Method
Cabinet maintenance
Cleaning the lint filter
Operation when objects are
dropped into outside of the spin tub
Anti-freezing protection
Main Technical Parameters
Accessories
Change the position of the drain hose
Installation site
Notes
Others
Lay upper drain hose
Attention To Installation
Preparation Instructions
Weight reference of washing materials
Attention To Maintenance
CONTENTS
Laundry volume and detergent
dosage reference
Packing List 9
4
Soak Function
Structure Instruction
Accessories
Name Of Parts
Structure Instruction
1
Inner spin cover Water inlet hose
Introduction Of Control Panel
Water inlet:be used to inject water to wash tub or spin tub.
Wash timer:be used to select required washing time.
Spin timer:be used to select required spinning time.
Wash selector:Select “ Normal”or“ Heavy”according to texture of clothes.
Drain selector: For washing or rinsing, select “ Wash”or“ Rinse”. For Draining ,select “Drain”.
※ he drawing above is for reference only, specific drawing is subject to actual models.T
Control panel
Wash cover
Drain hose
(For upper drain only)
Lint filter
Pulsator
Base
Spin cover
Cabinet
Safety cover
Frame
(For lower drain only)
Drain hose
wash tub
Power plug
Water inlet Wash timer Wash selector
Spin timer Water inlet
Drain selector
Wash timer
Heavy
Normal
Rinse Drain
Wash
Spin Timer
Wash Selector Drain Selector
Soak
35
15
10
5
Wash timer
Heavy
Normal
Rinse Drain
Wash
Spin Timer
Wash Selector Drain Selector
Water inlet Wash timer Wash selector
Spin timer Water inlet
Drain selector

Work clothes
(1120g)
Shirt
(300g)
Undershirt
(180g)
Blanket
(900g)
Underwear
(70g)
Bedsheet
(600g)
23
Attention To Installation
Lay upper drain hose
FOR UPPER DRAIN SYSTEM ONLY
Needs a drain hose with minimum diameter 3 cm, and minimum carry away capacity of
40 liters per minute.
For upper drain system, the drain hose must be placed at least 86 cm(30 inches) from the
bottom of washer , but not higher than 100 cm.
of
86cm<H<100cm
Installation site
Change the position of the drain hose
FOR LOWER DRAIN SYSTEM ONLY
Front
Drain hose
Buckle Blanket
Plug in power and connect the water inlet hose.
Lay down the lower drain hose and connect it to the sewer , or lay the upper drain hose to places as indicated
in page .
Check that there are no objects such as coins, hairpins, mud or sand in the pocket.
Strings should be knotted in advance to prevent entanglement.
Clothes can be classified for washing according to the texture, dirty
For small pieces (e.g., stockings) or fluffy clothes, put them into
2
degree and color.
a nylon net for washing.
Preparation Instructions
Installation Usage method
The dosage of washing detergent varies according to dirty degree and texture of laundries.
hose is located the spin side . According to the
installation site, the drain hose can also be installed
at the wash side of the machine . The method is
as follows:
The ex-factory installation position of the drain
at
Unplug the power cord and empty
water in the drain hose completely.
Spread a piece of soft cloth on the floor (e.g. a blanket)
and place the washing machine on it gently.
Take the drain hose out from the buckle
at the spin side, and put it into the buckle
at the wash side.
Hang up the drain hose kit.
in the following places:
In order to avoid electrical failure, discoloration and deformation, do not install the machine
Locations exposed to rain
or snow
Locations exposed
to direct sunlight
Locations with uneven
or unstable ground
Attachment :Laundry volume and detergent dosage reference
Attachment: Weight reference of washing materials
Fabric type
Cotton or linen
Laundry
capacity(kg)
Low
Synthetics,silk,
Delicate fabrics
High
Water flow
Normal
Heavy
Normal
Mid
Wash time
(minutes)
About 45
Detergent
amount(g)
About 67
About 67
About 90
About 67
About 90
High
Mid
Mid
Heavy soils
Water
level
0-5.0
5.0-9.0
0-9.0
9.0-14.0
9.0-14.0
0-9.0
3
3-5
7
7-10
10-35(soak 20)
10

45
Spinning Method
Inner
spin cover
Spin tub
Correct Incorrect
Spin cover
Safety cover
Washing materials
Wire
Light clothes
(fiber/blended)
Knitwear (fiber)
Underwear
(cotton)
Slipover
(cotton/linen)
Toweling coverlet
(cotton)
About 50
seconds
About 1
minute
About 1～2
minutes
About 2～3
minutes
About 3～4
minutes
About 5
minutes
Usage method Usage method
Washing Method
Rinsing Method
A. Spraying rinse (rinse in the spin tub)
Put the laundry into the spin tub after washing.
Turn on the water tap, choose to fill water into the spin tub for 3-4 minutes, and then turn off the water tap.
The above steps can be repeated.
Set the spin timer for 2-5 minutes for rinsing.
Note: If there is red rust in water, do not choose spraying rinse, for the rust is easy to adhere to laundries.
Ensure that do not fill water into spin tub when spinning.
To save time, water and energy, can do pre-spinning before rinsing.
1 to 5 minutes.
Put laundries which have already been dehydrated intothe wash tub.
After filling water to the desired level, turn off the water tap to save water.
Turn the “Wash-Drain selector” knob to the "Normal” or “Heavy”.
Set the “wash timer”to thedesired time (about 3-5 minutes)for rinsing.
After rinsing, put the washing materials into the spin tub to spin for
Drain out the rinsing water in the wash tub.
The above steps can be repeated.
Water level indicator
Fold in half along
the long edge
1/3 fold in the
same direction
Roll up the blanket Put into the tub with
blanket edge facing down
Dilute detergent with water (below 50℃), then pour the solution into
Fold the blanket as shown in the figure, and into the wash tub.
adequate the wash tub.
put it
This machine can wash blended blanket (less than 3kg) marked with the "hand washing" label.
Washing method is as follows:
water to the wash tub
2.
1. Insert the inlet hose into the , and choose injectingwater water inlet mouth
.
Put the laundry into the wash tub, and add detergent into it.
When fill water to half of the desired water level, turn off the
water tap and let laundries soak in the solution for minutes,
then fill water to desired water level.
(For machines having soak function only )
Wash timer
Soak
35
15
10
5
Wash timer
Spin timer
Spin timer
1.Shake out the laundry and put
them into the spin tub.
2.Put the inner spin cover on .
Confirm the inner spin cover is placed
horizontally.
the laundry
3.Close the safety cover and the
spin cover.
4.Refer to the following table to select
spinning time.
Spin time
3. Set wash program “Normal” or “Heavy” as per amount and
texture of laundries.
4. Turn the wash timer knob to set wash time.
5. After washing, set the wash drain selector to “Drain” position for draining.
Work time
about 5 about 5 about 5
Total: 35 (mins)
about 1.5 about 1.5
about 2
Static time
Soak Function
For seriously stained clothes, Soak wash is useful to achieve better wash result.
15-35 minutes of the wash timer is for soak wash:(illustrate as follows)
6. Buzzer will alarm the completion of washing.(For machines having buzzer function only)
B. Common rinse (rinse in the wash tub)
35 15
(unit：)mins
The appliance can not be used by children or persons with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction.
Please do not use other water inlet hoses, except for the water inlet hoses that are supplied as the accessories.
If need to replace the hose, please buy it from the local service center.
When choose to inject water to wash tub or spin tub,water injecting is forbidden.
the washing machine
is placed on a flat and stable floor ,and then adjust washing materials, distribute them evenly.
To do spinning and draining together, please spin for 1 minute before draining.
Do not wash or spin waterproof clothes or clothes that float easily to avoid abnormal vibration or damage to the
clothes.
If strong vibration occurs in time of spinning, open the spin cover immediately. Make sure that

控制面板图案
7
6
控制面板图案
After you use the washing machine, never forget to do the following two things:
Attention To Maintenance
Cabinet
Frame
Others
Maintenance
Cabinet maintenance Cleaning the lint filter
After using the washing machine , wipe
the moisture and stain on it with a
piece of soft cloth. To avoid damage
to the surface , do not use corrosive or
volatile chemicals.
Anti-freezing protection
To prevent from freezing:
If the water is frozen, please take the following steps:
Notes
Symptom Reason
The washing machine employs alternative current with rated voltage and frequency . When voltage fluctuates
between -10% and 10% of the rated voltage, the machine can work normally.
Connection mode of the power cord of this machine is Y-shaped connection. Users
or reconnect the wire by themselves. please contact the designated service center.
should not detach
If this part needs to be repaired,
Button head
1.Press the button head, and
pull the lint filter out.
Turn the filter net inside out, and rinse it
in water.
After inserting the claw, press the button
to insert it into place.
A click sound means proper installation.
Claw
hose completely.
Lay the drain hose and turn the drain selector knob to the "Drain”position to
empty the water in the tub.
Turn off the water tap, remove the water inlet hose and empty water in the water inlet
Keep about 2 liters of warm water below 50℃ in the wash tub for
about 10 minutes. and then lay the drain hose and turn the
wash drain selector knob to the "Drain”position to empty the water .
Fit the water inlet hose and turn on the water tap to
confirm water filling and draining work properly.
Put the water inlet hose into warm water of about 50℃.
Operation when objects are
dropped into the outside of the spin tub
Remove all screws on the frame with a screw driver.
Pull up the frame with both hands and turn it backwards.
Take out the clothes dropped into the outside of the spin tub.
Press the frame to reset and tighten screws.
2. Remove the water inlet hose.
1. Disconnect the power plug.
Be sure to use plug that is properly grounded.
The maximum gradient of the supporting surface for the washing machine should not exceed 2º.
Do not tear down electrical wires and components in the machine by yourself.
There are holes on the base for ventilation. These holes should not be blocked by foreign objects (carpets, etc.).
Never connect the grounding wire with the live wire, or it may lead to an electric shock.
If the power cord is damaged, it must be replaced by a qualified person to avoid a hazard.
After using, be sure to unplug the power plug.
If the following symptoms occur, please disconnect the power plug and perform the following
checks:
Check that the power supply is in good condition.
Check that the power plug is inserted properly.
Check that the wash timer knob or the spin timer knob is not
in the "0" position.
Check that the drain hose is not laid too high.
Check that the drain hose is not frozen.
Check that the drain hose is not blocked by foreign matter.
Check that there are no coins or any other foreign
objects dropped into the wash tub.
Check that the washing machine is placed on flat, stable floor.
Check that clothes are evenly distributed in the spin tub.
Check that there are no washing materials or foaming debris
dropped into the outside of the spin tub.
The washing
machine does
not work.
The drain hose
does not work.
There is abnormal
noise during washing.
There is abnormal
noise and violent
vibration during
spinning.

0thers
89
Be sure to comply with all the notes above.
Notes for scrubbing Do not use warm water above 50℃
Do not let children play near the tub Keep away from fire or heat source
Others
Keep the washing machine away from
fire or heat source such as heater,
cigarette, etc. to avoid fire
accident or plastic
deformation.
If the spin cover is opened in time of
spinning ,the washing machine
will arrest at once , which will
shorten its service life . So avoid
opening the spin cover during
spinning.Furthermore , do not
put hands into the wash tub
while the machine running,
for it is very dangerous.
Do not open the spin cover
in time of spinning Which can not be washed
Do not wash clothes that
are stained with paint,
petrol or other volatile or
flammable substance.
Avoid dampness
Do not put the washing machine in extreme
damp place, for dampness may weaken
insulation of the machine, which may lead to
electric shocks or faults.
Do not forget to close
the inner spin cover
If laundries in the
spin tub are tossed out,
they are easily damaged.
In order to avoid damaging
electrical components , do
not scrub operation parts
of control panel with water.
This will prevent plastic
deformation and aging.
Main Technical Parameters
Parameters
for children falling into
the tubs.
It's very dangerous
PACKING LIST
180W
450W
230V
50Hz
Parameter
Function
Wash
Spin 7.0kg
Net weight
30kg
Input Power
(upper drain)
Input Power
(lower drain)
Pump
180W
450W
45W
Power
Supply
Capacity
(dry Clothes)
/
5 min.
Water
volume
Maximum
Time
/
/
14.0 kg
Maximum water
pressure permitted
in the water inlet
0.6Mpa
15 min.
3
(soak wash)
5 min.
Overall dimension
(L X W X H)
902x537x974
(mm)
H: 90L
M: 67L
L: 45L
The washer can spin a single blanket (less than 3kg)marked with hand washing label.
The blanket must be folded in the following way
:
Approximate Weight of clothing
Fold in half Fold in 1/3 Roll up blanket Put blanket into the tub with
the edge downward
DO NOT OVERLOAD THE SPINNING TUB
Maximum capacity for the spinning tub is 7kg
Shirt
(300g)
Undershirt
(180g)
Underwear
(70g)
Blanket
(900g)
Bedsheet
(600g)
Work clothes
(1120g)
The spin motor will automatically switch off when overworked ,and will take
+/- 20 minutes to cool down.
Packing list
Quantity
Name Quantity
1 Set of washing machine
Accessories
Water inlet hose
Instruction manual
1
1
1
Note
Inner spin cover