Kenmore 79075722991 User manual

For Models with 4 Standard Sealed Top Burners
INSTALLATION AND SERVICE MUST BE PERFORMED BY
A QUALIFIED INSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
THIS CONVERSION KIT MUST BE INSTALLED BY A QUALIFIED SERVICE TECHNICIAN
IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS AND ALLAPPLICABLE CODES AND
REQUIREMENTS OFTHE AUTHORITY HAVING JURISDICTION. FAILURE TO FOLLOW INSTRUCTIONS
MAY RESULT IN FIRE, EXPLOSION OR PRODUCTION OF CARBON MONOXIDE CAUSING PROPERTY
DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. THE QUALIFIED SERVICE AGENCY IS RESPONSIBLE
FOR TH E PROPER INSTALLATION OF THIS KIT. THE INSTALLATION IS NOT PROPER AND COMPLETE
UNTIL THE OPERATION OF THE CONVERTED APPLIANCE IS CHECKED AS SPECIFIED IN THE
MANUFACTURER'S INSTRUCTIONS SUPPLIED WITH THE KIT.
BEFORE PROCEEDING WITH THE CONVERSION, SHUT OFF THE GAS SUPPLY BEFORE
DISCONNECTING ELECTRICAL POWER TO THE RANGE. BE SURE BOTH POWER SUPPLIES ARE OFF
BEFORE INSTALLING THE CONVERSION KIT. FAILURE TO DO SO COULD CAUSE SERIOUS BODILY
INJURY.
This kit contains the following:
Quantity Description Part Number
1
4
4
4
Top Burner Orifice Marked 0.89 mm (7,500 BTU*)
*For operation at elevations above 2000 ft., appliance rating shall be
reducedat the rate of 4 percent for each 1000 ft. above sealevel.
Installation Instructions
Restrictor-Burner
Screw-Restrictor
Choke-Burner: Small (7,500 BTU) Top Burners
316010802
316105828
316011600
316064200
316056700
Tools Required:
#1 Phillips Head Screwdriver (small) _--:=_
5/8" Open End Wrench
1/8" Wide Flat Blade Screwdriver
7mm Nutdriver _ _]
7qo.-r.qTizTq l/,; 'Flo.?'...<'7,z,/qq/;
7clo.7572- _lj "7_o.T57Z_-_q /
790.7,._77-.1qq)_; 79o. 7573-3.9q2-.,"
9o. 7xTz,Tq2-;
7go. 75"72_'_'q2.
Espahol- P_ginas 7-12
PIN 316105828 (0001)

How to Convert the Range for use
with LP/Propane Gas
1. Convert the Pressure Regulator
To access the regulator,remove the kick panel, storage
drawer or warmer drawer. If equipped with a broiler
drawer, open drawer completely. For models equipped
with warmer drawer, follow the instructions below to
remove warmer drawer,
a. _|Nkvivl_.l_t_ll_[C'tlElectrical Shock Hazard can occur and
result in serious injury or death. Disconnect electrical
power to the range before removing the warmer
drawer for servicing.
b. Open the drawer to the fully opened position.
c. Locate glide lever on each side of drawer, pull up on the
left glide lever and push down on the right glide lever
(see figure 1).
d. Pull the drawer away from the range.
Pullup with finger
[]
@@ @ @@
II II
Front Access
to Regulator:
Remove Kick Panel,
StorageDrawer, or
Warmer Drawer,
(See Owner's Guide
for Instructions).
If Equipped with
Broiler Drawer.
Open Broiler Drawer.
Pressure
Regulator
location at
rear of
range
Left Glide
RightGlide
...._er
p__ L[]
FIGURE 1
FIGURE 2
e. Do not remove the Pressure Regulator or allow it to
rotate or turn. Remove the dust protector from the
cap, Using a 5/8" wrench, unscrew the cap from the
pressure regulator. Do not remove the spring from
the regulator. Do not pull on spring.
f. Turn the cap over so the hollow end faces outward.
Place the solid end of the cap into the loop end of the
dust protector as shown in illustration below.
g. Replace the cap on the regulator. The letters LP should
be visible on the exposed end of the cap. Snap the dust
protector over the regulator cap.
Dust
Protector
Spring i_
FIGURE 3
Hollow End Solid End
Towards Towards
Regulator Regulator
for Natural Gas for LP/Propane Gas

2. Convert Surface Burners for use with LP/
Propane Gas (see Figure 4)
[Ir_ Unlike the standard gas range, THIS COOKTOP
IS NOT REMOVABLE. Do not attempt to remove this
cooktop.
a. Remove the top grates and burner caps.
b. Remove the natural gas orifice using a 7ram nutddver,
Save the orifices removed from the appliance for future
use to convert back to natural gas.
c. Replace with supplied 0.89ram orifice. Tighten the
orifice until snug. Do not over tighten.
d. Insert the LP/Propane restrictor in the cavity directly
opposite the electrode, curved side facing the center of
the burner.
e. Tighten the restrictor securely in place using the screw
supplied. Do not over tighten,
f. Remove screw "A".
g. Insert the choke, flat side down.
h. Replace screw "A". Be sure the screw head is in line with
the recess in the choke.
i. Replace burner caps and top grates.
Burner
Cap Screw
Choke : : Restrictor
Screw
Electrode
FIGURE 4
Use caution when replacing the burner cap
so the electrode is not damaged, 5/8"
BurnerFlameSize _ _-
FIGURE 5
Note: Air mixture adjustment not required on top burners.
3. Convert Oven Burner Orifice for LP/Propane
Gas (16,000 BTU*)
a. Locate the oven burner spud shown in Figure 6.
b. Using a 1/2" wrench, turn down the adjustable spud,
which injects gas into the oven burner, until snug
against the LP/Propane metering pin (approximately
2-1/2 turns). Do not over tighten.
Oven Burner
Orifice
FIGURE 6
4. Convert Waist-High Broiler Burner Orifice
Flame for LP/Propane Gas (13,500 BTU*) --Self-
Cleaning Models Only
a. Open the oven door.
b. Locate the broiler burner spud and turn down until
snug against the LP/Propane metering pin
(approximately 2-1/2 turns). Do not over tighten.

5. Reconnect Gas and Electrical Supply to
Range.
Leaktestingoftheapplianceshallbeconductedaccording
to the Installation Instructions provided with the Range.
Checking Manifold Gas Pressure
If it should be necessary to check the manifold gas pressure,
remove the burner cap, choke, and connect a manometer
(water gauge) or other pressure device to the top right rear
burner orifice. Using a rubber hose with inside diameter of
approximately 1/4," hold tubing down tight over orifice.
Turn burner valve on. For an accurate pressure check, have
at least two (2) other surface burners burning. Be sure the
gas supply (inlet) pressure is at least one inch above
specified range manifold pressure. The gas supply pressure
should never be over 14" water column. When properly
adjusted the manifold water column pressure is 10" for LP/
Propane gas or 4" for Natural gas.
Do not use a flame to check for gas leaks.
a. Disconnect the range and its individual shut-off valve
from the gassupply piping system during any pressure
testing of that system at test pressures greater than 14"
of water column pressure (approximately 1/2" psig).
b. The appliance must be isolated from the gas supply
piping system by closing its individual manual shut-off
valve during any pressure testing of the gas supply
piping system at test pressures equal to or lessthan 14"
of water column pressure (approximately I/2" psig),
6. Adjust the "LOW" Setting for Linear Flow
Surface Burner Valves:
To
Surface
Burner
FIGURE 7
Test to verify if "LOW" setting should be adjusted
a. Push in and turn control to LITE until burner ignites.
b. Push in and auickly turn knob to LOWEST POSITION.
c. If burner goes out, reset control to OFF.
d. Remove the surface burner control knob.
e. Insert a thin-bladed screwdriver into the hollow valve
stem and engage the slotted screw inside. Flame size
can be increased or decreased with the turn of the
screw. Turn counterclockwise to increase flame size.
Turn clockwise to decrease flame size.
Adjust flame until you can quickly turn knob from LITE to
LOWEST POSITION without extinguishing the flame. Flame
should be as small as possible without going out.
7. Air Shutter-Oven Burner
The air shutter for the oven burner may need adjustment,
especially if the unit has been converted for use with LP/
Propane gas. The approximate flame length of the oven
burner is 1 inch (distinct inner, blue flame).
1' Flame Burner
_Baffle
FIGURE 8
To determine if the oven burner flame is proper:
a. To access the air shutter you must remove the warmer
drawer, see instructions on page 2.
b. Remove the oven bottom by removing the screws at
rear of oven bottom. Lift up the rear of oven bottom
and slide toward back of range to disengage from front
of oven front frame.
c. Remove burner baffle by removing nut located on top
of baffle and two screws from front edge of oven front
frame. Lift baffle straight up and out of the oven.
d. Settheoventobakeat350°Fandobservetheflame. If
the flame is yellow in color, increase air shutter opening
size. If the flame is a distinct blue color, but lifting away
from the burner; reduce the air shutter opening size.
e. Turn off oven and allow to cool before adjusting air
shutter. To adjust loosen lock-screw (See Figure 9),
reposition air shutter, and tighten lock-screw.
4

Burner
8. Air Shutter-Broil Burner
a. Observe the flame to determine if the broiler burner
flame is properly adjusted. It should be steady with
approximately 1" blue cones and no yellow or orange
flame tips.
®
Locking
Screw
QAir Shutter
_Q Orifice Hood
(Spud)
FIGURE 9
Retest the burner by repeating step "d" above. When the
burner flame isa distinct blue color burning steady, the air
shutter is adjusted correctly.
f. Replace burner baffle and oven bottom.
H
FIGURE 11
b. If adjustment to the air shutter is necessary, locate the
broiler bumer air shutter, loosen shutter set screw, and
adjust to obtain optimum flame. This will normally be
compJetely open for LP/Propane gas. If the flame is
yellow in color, increase the air shutter opening size. If
the flame is a distinct blue, but lifting away from the
burner, reduce the air shutter opening size. Tighten the
shutter set screw.
Removab e)j-"
Waist-High Burner
(Self Clean Models)
_Air Shutter
Lower Oven Bottorr
(Removable)
'_ Air Shutter
FIGURE 10
Oven
Burner
Tube
ll--
® Lock,orew ®
(_Air Shutter _Orifice
Hood
FIGURE 12
5

9. Replace Kick Panel, Storage Drawer or
Warmer Drawer:
(instructions for warmer drawer)
a. Pullthe bearingglidesto thefront ofthechassis
glide (see picture below).
b. Align the glide on each side ofthe drawer with the glide
slots on the range.
c. Push the drawer into the range until levers "click"
(approximately 2"). Pull the drawer open again to seat
bearing glides into position. If you do not hear the
levers "click'" or the bearing glides do not feel
seated remove the drawer and repeat steps "a"
through "c". This will minimize possible damage to the
bearing glides,
FIGURE 13
CONVERSION TO NATURAL GAS
If it becomes necessary to convert the range back to natural gas:
a. Disconnect gas and electrical supply from range.
b. Convert pressure regulator, turn cap over so the solid end of
cap faces outward. Place the hollow end of the cap into the
loop end of the dust protector. (See step 1.)
c. Replace .89 mm orifices in the top burners with original 1.60
mm orifices. Remove the LP/Propane restrictor in the cavity
directly opposite the electrode. Replace screw previously
holding restrictor in place. Do not over tighten. Remove the
choke. Replace screw previously holding choke in place. Do
not over tighten. (See step 2.)
d. Convert Oven Burner Orifice for Natural Gas by loosening
spud counter-clockwise (approximately 2-1/2 turns). (See
step 3.)
e. Convert Waist-High Broiler Burner Orifice (Self-Cleaning
Models On_y) for Natural Gas by loosening spud counter-
clockwise (approximately 2-1/2 turns). (See step 4.)
f. Readjust "LOW" Setting for Surface Burner Valves following
instructions. (See step 6.)
g. Readjust Oven & Broil Burner Air Shutters. (See steps 7 & 8.)
6