Kenmore 79032333000 User manual

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.
iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.
READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.
if the information in this manual is not followed exactly, afire or
explosion may result causing property damage, personal injury or death.
FOR YOUR SAFETY:
Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
WHAT TO DO iF YOU SMELL GAS:
*Do not try to light any appliance.
*Do not touch any electrical switch; do not use any phone in your building.
* immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
* if you cannot reach your gas supplier, call the fire department.
installation and service must be performed by a qualified installer,
service agency or the gas supplier.
Appliances Installed in the
state of Massachusetts:
This Appliance can only
be installed in the state
of Massachusetts by a
Massachusetts licensed
plumber or gas fitter.
This appliance must be
installed with a three (3)
foot /36 in. long flexible
gas connector. A "T"
handle type manual gas
valve must be installed in
the gas supply line to this
appliance.
GcIs 30" rain
Cutout Dimensions Figure |
36" Gas Cookto 34 1,,_ 19 1/8 19 3,_
All dimensions are stated in inches and (cm).
Dimension H includes a 5" (12.7 cm) space underneath the cooktop for connection to gas supply line.
NOTE: Wiring diagrams for this cooktop are enclosed in this booklet
Printed in United States
318201491 (1004) Revo A
English - pages 1-9
Espa_ol - p6ginas 10-18
Wiring Diagram 19-20

important Notes to the installer
1. Read all instructions contained in these
installation instructions before installing the
cooktop.
2. Remove all packing material before connecting
the electrical supply to the cooktop.
3. Observe all governing codes and ordinances.
4. Be sure to leave these instructions with the
.
consumer,
Note: For operation at 2000 ft. elevations
above see level, appliance rating shall be
reduced by 4 percent for each additional
1000 ft.
Important Note fo the Consumer
Keep these instructions with your Use and Care
Guide for future reference.
iMPORTANT SAFETY
iNSTRUCTiONS
installation of this cooktop must conform with
local codes or, in the absence of local codes,
with the National Fuel Gas Code ANSI Z223.1/
NFPA 54 in the United States, or in Canada, with
the Canadian Fuel Gas Code, CAN/CGA B149
and CAN/CGA B149.2.
* When installed in a manufactured (mobile)
home installation must conform with the
Manufactured Home Construction and Safety
Standard, title 24 CFR, part 3280 [Formerly
the Federal Standard for Mobile Home
Construction and Safety, title 24, HUD (part
280)] or, when such standard is not applicable,
the Standard for Manufactured Home
Installation, ANSI/NCSBCS A225.1 or with local
codes where applicable.
*Be sure your cooktop is installed and
grounded properly by a qualified installer or
service technician.
* This cooktop must be electrically grounded
in accordance with local codes or, in their
absence, with the National Electrical Code
ANSI/NFPA No. 70--latest edition in
the United States, or in Canada, with the
Canadian Electrical Code, CSA C22.1 Part 1.
" The burners can be lit manually during an
electrical power outage. To light aburner,
hold a lit match to the burner head, then
slowly turn the Surface Control knob to LITE.
Use caution when lighting burners manually.
* Do not store items of interest to children in
cabinets above the cooktop. Children could be
seriously burned climbing on the cooktop to
reach items.
*To eliminate the need to reach over the
surface burners, cabinet storage space above
the burners should be avoided.
" Adjust surface burner flame size so it does not
extend beyond the edge of the cooking utensil.
Excessive flame is hazardous.
*Never use your cooktop for warming or
heating the room. Prolonged use of the
cooktop without adequate ventilation can be
hazardous.
* Do not store or use gasoline or other
flammable vapors and liquids near this or any
other appliance. Explosions or fires could result.
The electrical power to the cooktop
must be shut off while gas line connections are
being made. Failure to do so could result in
serious injury or death.
This cooktop has been design certified by CSA
International. As with any appliance using gas
and generating heat, there are certain safety
precautions you should follow. You will find them
in the Use and Care Guide, read it carefully.

13" (33 cm)
Max. Depth
For Cabinet
Installed
Above
Cooktop.
18" Min.
(45.7 cm)
2" (5.1 cm) Minimum Distance
Between Rear Edge of Cutout
Nearest Combustible
Surface Above Countertop.
30" (76.2 cm) Min.
Clearance Between
the Top of the
Cooking Platform
and Unprotected
__detr Metal
Clearance
\ .................
i
24" IV]in. 21/4'' (5.7 cmi Min.
(61 era) From Counter Edge to
X _ Front Edge of Cutout.
i i ..................
\ ...... ..... -If a drawer is present underneath,
\_ allow at least 61/2'' (16.5 cm)
To eliminate the risk of
burns or fire from reaching over
heated surfaces, cabinet storage
space located above the cooktop
should be avoided. If cabinet
storage is provided, risk can be
reduced by installing a range hood
that projects horizontally a
minimum of 5" (12.7 cm) beyond the
bottom of the cabinets.
of clearance below the counter
top. Make sure there will be no
interference with gas or electrical
connection. Never store flammable
products in the drawer.
30" Cooktop 30" (76.2cm) 7" (17.8cm) 7" (t7.8cm)
36"Cooktop 36" (91.4cm) 7" (17.8cm) 7" (17.8cm)
Figure 2 =CABINET DESIGN
3

Typical Under Counter Installation of an Electric Built-in Oven with a
Cooktop Mounted Above
All mounting hardware must
be used to secure the built-in
oven to the cabinets. Refer to
the built-in oven installation
instructions.
Junction box
must be located
approx. 3*wto the
left of the built-in
oven cutout.
This cooktop may be
installed over certain
built-in electric oven
models.
Side filler panels are necessary
to isolate the unit from adjoining
cabinets. Panel height should allow
for installation of approved cooktop
models. See "Typical Gas Cooktop
Installation Over an Electric Built-in
Oven Installed Under the Counter" on
next page.
208/240 Volt
grounded junction
box for built-in oven.
i
Cut an opening in wood base minimum 4"
(10.2 cm) x 4" (10.2 cm) to route armored
cable to junction box.
Unit will
overlap
cutout
(minimum)
edges by
1" (2.5cm) 4 1/2" (11.4 cm)
Max. _
36"
(91.4 cm) Min.
Use 3/4" (1.9 cm)
plywood, installed on
two runners, flush with
toe plate. Base must be
capable of supporting
150 pounds (68 kg) for
27" models and 200
pounds (90 kg) for 30"
models.
If no cooktop is
installed directly
over the oven
unit, 5" (12.7cm)
maximum is
allowed. 30" (76.2) 27 _A"(69,2cm) 28_A'' (71.8) 28_A'' (72.4) 29" (73.7) 23_A'' (59.7)
27" (68.6) 27 _A"(69,2cm) 28_A'' (71.8) 247/?' (63.2) 25_A'' (64.1) 23_A'' (59.7)
Figure 3

Typical Gas Cooktop Installation Over
an Electric Built-in Oven Installed Under the Counter
FRONT VIEW
18"
14_---- (45.7 cm)
_ Max.
GAS COOl<TOP : i J
[Approx.
..... 61/2 _ [
F_areUn_on"IJ< [
WALL OVEN CABINET %9
Cabinet sides or _ _:_r_o r
Manual Shutoff: Valve
(To be accessible
for shut-off valve
operation)
SIDE VIEW
........_ GAS COOl<TOP [
!
/i
WALL OVEN : :
Figure 4
5

1. Wall Outlet Location
12" _1
,__.(30.58cm)
12_0.3cm)-I _-_ 10"
<25._,cm>
120V grounded outlet
on rear wall.
_Center line 22"
Of unit (55.9 cm)
, NOTE:If an outlet
't is not available, [
, haveone installed by |
'l aqualified technician.
"" ._Center line
Of unit Figure 5
To clamp down, insert an angle bracket into the slot
on each side of the unit as shown. Run thumb screw
up through the bracket, up against the bottom of the
counter. Tighten until the unit draws down and is secure.
3. Provide an Adequate Gas Supply
This cooktop is designed to operate on natural gas at 4"
of manifold pressure only.
A pressure regulator is connected in series with the
manifold on the cooktop and must remain in series with
the supply line.
For proper operation, the maximum inlet pressure to the
regulator must be no more than 14" of water column
(W.C.) pressure.
For checking the regulator, the inlet pressure must be at
least !" (or 2.5 kPa) greater than the regulator manifold
pressure setting. The regulator is set for 4" of manifold
pressure, the inlet pressure must be at least 5".
The gas supply line to the range should be 1/2" or 3/4"
pipe.
2. Cooktop Installation
1. Visually inspect the cooktop for damage.
2. Set the cooktop into the countertop cutout.
After inserting the cooktop into the countertop opening,
make sure the unit is sitting on the metal flange around
the top of the burner box. Cooktop must not sit on the
glass or the porcelain top. Avoid cutting an oversized
hole in the countertop.
NOTE: Do not use caulking compound; cooktop should
be removable for service when needed.
Granite countertop Installation Kit
A Granite Countertop Installation kit # 903103-9010 can
be ordered through a Sears Service Center.
Clamp Down Information
Once the cooktop is installed in the counter opening,
you must clamp the unit down as shown.
4. LP/Propane Gas Conversion
This appliance can be used with Natural gas or LP/
Propane gas. It is shipped from the factory for use with
natural gas.
A kit for converting to LP gas is supplied with your
cooktop. The kit is marked "FOR LP/PROPANE GAS
CONVERSION".
The conversion must be performed by a qualified
service technician in accordance with the kit instructions
and all local codes and requirements. Failure to follow
instructions could result in serious injury or property
damage. The qualified agency performing this work
assumes responsibility for the conversion.
Failure to make the appropriate
conversion can result in serious personal injury and
property damage.
Seal
Coaktap _k.._ Counferfop
I
Angle ._
Brackef
Thumb
_Screw
Figure 6
Important: Remove all packing material and literature
from cooktop before connecting gas and electrical
supply to cooktop.

5. install Pressure Regulator
Install the pressure regulator with the arrow on the
regulator pointing up toward the unit in a position
where you can reach the access cap.
Do not make the connection too tight.
The regulator is die cast. Overtightening may crack the
regulator resulting in a gas leak and possible fire or
explosion.
Manual GAS FLOW Pressure
Shutoff Flare _-t1_ Flare Regulator
Valve Union Union
_-_ Nipple Flexible NJppl Access
Off Connector Cap
All connections must be wrench-tightened
Figure 7
The supply line must be equipped with an approved
manual shutoff valve. This valve should be located
in the same room as the cooktop and should be in a
location that allows ease of opening and closing. Do
not block access to the shutoff valve. The valve is for
turning on or shutting off gas to the appliance.
Shutoff Valve -
Open position
Figure 8
Assemble the flexible connector from the gas supply
pipe to the pressure regulator in the following order:
1. manual shutoff valve
2. 1/2" (1.3 cm) nipple
3. 1/2" (1.3 cm) flare union adapter
4. flexible connector
5. 1/2" (1.3 cm) flare union adapter
6. 1/2" (1.3 cm) nipple
7. pressure regulator
Use pipe-joint compound made for use with Natural
and LP/Propane gas to seal all gas connections. If
flexible connectors are used, be certain connectors are
not kinked.
Once regulator is in place, open the shutoff valve in the
gas supply line. Wait a few minutes for gas to move
through the gas line.
Check for leaks. After connecting the cooktop to
the gas supply, check the system for leaks with a
manometer. If a manometer is not available, turn on the
gas supply and use a liquid leak detector (or soap and
water) at all joints and connections to check for leaks.
Do not use a flame to check for leaks
from gas connections. Checking for leaks with a flame
may result in a fire or explosion.
Tighten all connections if necessary to prevent gas
leakage in the cooktop or supply line.
Check alignment of control knob valves after
connecting the cooktop to the gas supply to be sure the
cooktop manifold pipe has not moved. A misalignment
could cause the valve stems to rub on the control panel,
resulting in a gas leak at the valve.
Disconnect this cooktop and its individual manual
shutoff valve from the gas supply piping system during
any pressure testing of that system at test pressures
greater than 1/2 psig (3.5 kPa or 14"water column).
Isolate the cooktop from the gas supply piping system
by closing its individual manual shutoff valve during any
pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig (3.5 kPa or 14"
water column).
7

6. Electrical Requirements
120 volt, 60 Hertz, properly grounded branch circuit
protected by a 15 amp circuit breaker or time delay
fuse. Do not use an extension cord with this cooktop.
Grounding Instructions
iMPORTANT Please read carefully.
For personal safety, this appilance must be properly
grounded.
The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong grounding wall receptacle (see Figure 9) to
minimize the possibility of electric shock hazard from
the appliance.
The wall receptacle and circuit should be checked by
a qualified electrician to make sure the receptacle is
properly grounded.
Where a standard 2-prong wall receptacle is installed,
it is the personal responsibility and obligation of the
consumer to have it replaced by a properly grounded
3-prong wall receptacle.
Preferred Method
Grounding type
wail receptacle
not, under
circumstances,
cut, remove,
or bypass the
grounding prong.
7. Check Operation
Refer to the Use and Care Guide packaged with the
cooktop for operating instructions and for care and
cleaning of your cooktop.
1. Remove foam caps.
2. Turn on Electrical Power and Open Main Shutoff
Gas Valve
.Check the igniters
Operation of electric igniters should be checked
after cooktop and supply line connectors have been
carefully checked for leaks and the cooktop has
been connected to electric power.
To operate the surface burner:
A. Push in and turn a surface burner knob to the
LITE position. You will hear a small ticking noise;
this is the sound of the electric ignitor which
lights the burner.
B. After the burner lights, turn to the desired flame
size. The controls do not have to be set at a
particular mark. Use the marks as a guide and
adjust the flame as needed.
Power supply cord with
3-prong grounding plug.
Figure 9
Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord.
Disconnect electrical supply cord
from wall receptacle before servicing cooktop.

4. Adjust the "LOW" setting for regular surface
burner valves (Figure 10)
a. Push in and turn control to LITE until burner ignites.
b. Quickly turn knob to LOWEST POSITION.
c. If burner goes out, reset control to OFF.
d. Remove the surface burner control knob.
e. Insert a thin-bladed screwdriver into the hollow valve
stem and engage the slotted screw inside. Flame size
can be increased or decreased with the turn of the
screw. Turn counterclockwise to increase flame size.
Turn clockwise to decrease flame size. Adjust flame
until you can quickly turn knob from LITE to LOWEST
POSITION without extinguishing the flame. Flame
should be as small as possible without going out.
Counterclockwise
Clockwise
5. Adjust the "LOW" setting of the dual burner surface
valve (Figure 10) (some models):
Note: On the dual valve the low setting of each portion
should be adjusted individually.
a. Push in and turn knob to LITE then continue to turn
until only the inner portion of the dual burner stays on.
b. QulckJy turn knob to LOWEST POSITIQN.
c. If burner goes out, reset control to OFF.
d. Remove the surface burner control knob.
e. The inner portion of the dual burner flame size
can be increased or decreased with the turn of the
screw B. Use screw A to adjust the low flame size
of the outer portion of the dual burner. Turn the
screw counterclockwise to increase flame size. Turn
the screw clockwise to decrease flame size. Adjust
flame until you can quickly turn knob from HIGH to
LOWEST POSITION without extinguishing the flame.
Flame should be as small as possible without going
out.
Note: Air mixture adjustment is not required on surface
burners.
When All Hookups are Complete
Make sure all controls are left in the OFF position.
Make sure the flow of combustion and ventilation air to
the cooktop is unobstructed.
Regular
Burner
Valve
Figure 10
Note: Air mixture adjustment is not required on surface
burners.
Model and Serial Number Location
The serial plate is located on the underside of the
cooktop.
When ordering parts for or making inquires about your
range, always be sure to include the model and serial
numbers and a Jot number or letter from the serial plate
of your cooktop.
Your serial plate also tells you the rating of the burners,
the type of fuel and the pressure the cooktop was
adjusted for when it left the factory.
Before You Call for Service
Read the Before You Call for Service Checklist and
operating instructions in your Use and Care Guide.
It may save you time and expense. The list includes
common occurrences that are not the result of defective
workmanship or materials in this appliance.
Refer to the warranty in your Use and Care Guide for
our service phone number and address. Please call or
write if you have inquiries about your product and/or
need to order parts.
9

LA INSTALACION Y ELSERVICIO DEBEN SER REALIZADOS POR UN INSTALADOR CALiFICADO.
IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA USO DEL iNSPECTOR ELECTRICO LOCAL,
LEA Y GUARDE ESTAS INSTRUCCIONES PARA FUTURAS REFERENCIAS
Si todas las instrucciones de _ste manual no son
observadas a la letra, se puede ocurrir incendios oe×plosiones clue
pueden causar da_os materiales, lesiones ola muerte.
PARA SU SEGURIDAD:
--No aimacene outilice gasolina u arras vapores y licluidos inflamabies cerca
de _ste o cualcluier otto artefacto.
--QUE HACER SI HAY FUGAS DE GAS :
*No intente de encender ning0n artefacto
*No toque ning0n interruptor el_ctrico; no utilice ning0n aparato
telef6nico en su edificio.
* Llame inmediatamente el abastecedor de gas desde el tel_fono de un
vecino. Siga las instrucciones del abastecedor de gas.
* En caso clue no puede contactar el abastecedor de gas IJame al
departamento de bomberos.
--La instalaci6n y el servicio telef6nico deben set realizados par un instalador
calificado, par un servicio t_cnico certificado o par el abastecedor de gas.
Aparatas Instaladas en el
estado de Massachusetts:
Este Aparclto s61o puede
set instaiado en ei estcldo
de Massachusetts por un
piomero oajustador de gas
iicenciado de Massachusetfo
Este aparato se debe
instaiar con un largo
conector flexible de gas de
tres (3) pies/36 puigadas.
Una v6lvula manual de gas
de tipo manija de farina de
"T" se debe instaiar en ia
iinea dei suministro de gas
de este aparato.
DJmensiones 30" min
de la parrilla (76.2 cm)
de cocinar
C
21/'2"
(6.4
DJmensJones
del hueco de la
parrilla de cocinar
Modelo de 30" 30 (76.2) 21 3_ (55.2) 4 1/4(10.8) 27 (68.6) 19 (48.3)
ModeJo de 36" 36 (91.4) 21 3_ (55.2) 4 1/4(10.8) 33 1/4(84.5) 19 (48.3)
Modelo de 30" 26 s/8 (67.6) 26 7/8 (68.3) 19 (48.3) 193/8 (49.2) 8 (20.3)
Modelo de 36" 33 7/8 (86.1) 34 1/4(87) 19 1/8 (48.6) 19 3_ (50.2) 8 (20.3)
Todas las dimensiones se dan en pulgadas (cm).
La dimensi6n H inciuye un espacio de 5" por debajo de ia plancha de cocinar para ia 318201491 (1004) Rev. A
conexi6n de ia iinea de suministro de gas. English - pages 1-9
NOTA: Se adjunta los diagramas de cabJes de es|a pJancha de cocinar con el IJbre|a. Espa_ol - p6ginas 10-18
Imprimido en los Estados Unidos Diagrama de la instalaci6n alambica 19-20