Kenmore 66513734K604 User manual

Installation
Instructions
=~
. .
er
|
Gne
bon
Instrucciones
de
instalacion
ort
Instructions d' installation
English / Espafiol / Francais
kenmore.
(Modéles & trés grande cuve en plastique)
P/N W10282552B
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.
www.kenmore.com
www.sears.com
www.sears.ca

TABLE OF CONTENTS
DISHWASHER SAFETY 2 INSTALLATION INSTRUCTIONS 6
INSTALLATION REQUIREMENTS 3 Prepare cabinet opening using existing utility hookups «uw 6
Tools and Parts 3 Prepare cabinet opening where there are no existing
Location Requirements 3 utility hookups 7
Drain Requirements 5 Prepare Dishwasher 9
Water Supply Requirements 5 Make Electrical Connection 12
Electrical Requirements 5 Connect to water supply 13
Connect to drain 14
Secure dishwasher in cabinet Opening ........eeeesesseeseeeeseeseeeeeeeeeee 14
INDICE 16
TABLE DES MATIERES 31
DISHWASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER?” or “WARNING.”
These words mean:
WN You can be killed or seriously injured if you don't immediately
DANG ys] follow instructions.
You can be killed or seriously injured if you don't follow
A NST i NG instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
You need to:
the dishwasher. Remove shipping materials, drain hose and
lower rack. Close dishwasher door until latched.
m@ Observe all governing codes and ordinances.
m Install this dishwasher as specified in these instructions.
: Hg Installation should be performed by a qualified service
Tip Over Hazard technician. The dishwasher must be installed to meet all
Do not use dishwasher until completely installed. electrical and plumbing national and local codes and
ordinances.
Do not push down on open door.
Doing so can result in serious injury or cuts.
AWARN I NG m Slowly open dishwasher door while someone grasps the rear of

INSTALLATION REQUIREMENTS
POP oy yoy bye gtong upry pike EE pomp ups Pager
Tools and Parts
Gather the required tools and parts before starting installation.
All installations
Tools needed: m Small level
m Pliers mg Flashlight
mg Phillips screwdriver m= Shallow pan
gm %eé' and 4" nut drivers or mm %" open-end wrench
hex sockets mg Bath towel
Measuring tape or ruler Bm Wood block
m 10" adjustable wrench that Parts Needed:
to 1%" (2.9
opens to 178 (2.9 em) mw Shims (if installed with
gm Flat-blade screwdriver built-up floor)
m Utility knife m %" Compr x 94" hose
MH 2 twist-on wire connectors fitting. Contact your local
Sears Store to purchase Kit
Number 11000.
which are the proper size to
connect your household
wiring to 16-gauge wiring
in dishwasher
In addition, for new installations
Tools needed: Parts needed:
m= Cordless drill with ¥2", 4", m@ ~=Copper tubing (%"
and 11" hole saw bits recommended) or flexible
= = Small tubing cutter stainless steel braided fill
ine
gm Wire stripper
PP m Clamp connector or
conduit connector to fit a
7/3" (2.2 cm) diameter hole
m 112" to 2" screw-type clamp
if connecting to waste-tee
Parts supplied
A. 2 — drain hose clamps, | large and 1 small
B.2-—#10x YY." Phillips-head screws
C. Drain hose
D. 2 — undercounter side mount brackets
E. 2 — undercounter mounting brackets (top)
Make sure all these parts are included. If not included, call
1-800-4MY-HOME.
See separate parts list for accessories available for your
dishwasher.
&
Gt ll Gon als BH
Do not run drain lines, water lines or electrical wiring where they
can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must provide
clearance between motor and flooring. Motor should not touch the
floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher against
freezing. Damage from freezing is not covered by the warranty.
A side panel kit is available from your dealer for installing your
dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277) is available
from your dealer for installing underneath the countertop. This may
also be obtained by calling 1-800-4MY-HOME.
Check location where dishwasher will be installed. The location
must provide:
mM easy access to water, electricity and drain.
HM convenient access for loading and unloading dishes. Corner
locations require a 2" (5.1 cm) minimum clearance between the
side of the dishwasher door and the wall or cabinet.
HM square opening for proper operation and appearance.
m cabinet front perpendicular to floor.
mg level floor. (If floor at front of opening is not level with floor at
rear of opening, shims may be needed to level dishwasher.)
NOTE: To avoid shifting during dishwasher operation, shims must
be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it winterized by
authorized service personnel.
Make sure pipes, wires and drain hose are within the shaded area
shown in the “Cutout dimensions” section.
Helpful Tip: If the floor in the dishwasher opening is uneven
(example: tile flooring only partway into opening), you will
need to be exact in measuring dimensions and in leveling
dishwasher.

Product dimensions Cutout dimensions
%" (1.9 om) >| <— 2514" (64.1 cm) —— 2» _
re be [ee 24¥6" (62.2 cm) —so h
compressed \
(not used on all 5 i <i 24" (61 cm)** a
models)
a All surfaces must be free —~
from intrusions on
337%" ay" 34"
(86
cm)
min.
(6.4
cm)t
6"
(86.4
cm)
with
wheels
*
rin.*
removed
(17.2
om)
a
2a"
~ “ “ (61 cm)
134 pel \ [ee 10% 3" min. ~~
(4.4.0m)¢ P67 om) | |7om)t
6" aa
LA (15.9 cm)*** 2
G.1 em)t
<— 21" (53.3 cm) >| y
6%"
15.9 pee
SIDE VIEW J h (5:9 em}
9"
_ (22.9 em) (6.1 em) 10"
: A" ae (25.4 cm) |.
eg 237" (60.6 cm) ———pe} (4.4 em}+ (16.8 em)t clear area $
VA \ Cut holes in shaded area of cabinet walls or floor as specified
below:
water line — 1%" (1.3 cm)
drain line — 112" (3.8 cm)
direct wire — 4" (1.9 cm)
power supply cord — 14" (3.8 cm)
*Measured from the lowest point on the underside of countertop.
May be reduced to 3378" (86 cm) by removing wheels from
dishwasher.
** Minimum, measured from narrowest point of opening.
r) Ct *** May be increased to 6%" (175 cm) if height of opening is
i i 342" (87.6 cm) at its lowest point.
al {Both sides
REAR VIEW

Py
LAPCn KequTremen’s
a
SEN
S
aOR
S
ae
m Use the new drain hose supplied with your dishwasher. If this is
not long enough, use a new drain hose with a maximum length
of 12 ft (3.7 m) that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, and fits the 1"
(2.5 cm) drain connector of the dishwasher.
mM Connect drain hose to waste tee or disposer inlet above drain
trap in house plumbing and 20" (50.8 cm) minimum above the
floor. It is recommended that the drain hose either be looped
up and securely fastened to the underside of the counter, or be
connected to an air gap.
m Use an air gap if the drain hose is connected to house plumbing
lower than 20" (50.8 cm) above subfloor or floor.
m Use 1" minimum |.D. drain line fittings.
y
Water Supply Requirements
mg A hot water line with 20 to 120 psi (138 to 862 kPa) water
pressure.
m 120°F (49°C) water at dishwasher.
m %" ©.D. copper tubing with compression fitting or flexible
stainless steel braided fill line (Y2" minimum plastic tubing is not
recommended).
m A90° elbow with ¥8" N.PT. external pipe threads on one end.
Do not solder within 6" (15.2 cm) of water inlet valve.
on itn, olor g ge
eCiric fa Be 1 yp, a
se
SOs a r
Ay
Contact a qualified electrician.
Assure that the electrical installation is adequate and in
conformance with all national and local codes and ordinances.
You must have:
mM 120-volt, 60 Hz, AC-only, 15- or 20- amp, fused electrical
supply.
mM Copper wire only.
We recommend:
m A time-delay fuse or circuit breaker.
m A separate circuit.
If direct wiring dishwasher:
m Use flexible, armored or nonmetallic sheathed, copper wire
with grounding wire that meets the wiring requirements for your
home and local codes and ordinances.
m_ Use strain relief method provided with house wiring junction
box or install a UL Listed /CSA Approved clamp connector to
the house wiring junction box. If using conduit, use a UL Listed /
CSA Approved strain relief.
If connecting dishwasher with a power supply cord:
m Use Power Supply Cord Kit (Part Number 4317824) marked for
use with dishwashers. Kit contents include:
— Volex, Inc., UL Listed 16 gauge 3 wire power supply cord with
3 prong grounded plug.
— Neer C-500 “4" strain relief.
— 3 wire connectors.
— Part Number 302797 grommet
Follow the kit instructions for installing the power supply cord.
m Power supply cord must plug into a mating 3 prong, grounded
outlet, located in the cabinet next to the dishwasher opening.
Outlet must meet all local codes and ordinances.

INSTALLATION INSTRUCTIONS
I
edt
|
N
G
Install
the
drain
hose
IMPORTANT: Always use a new drain hose when installing a new
Y replacement dishwasher.
1. Drill a 1%" (3.8 cm) diameter hole in cabinet wall or floor on
the side of the opening closest to the sink.
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
2. Connect drain hose to waste tee or waste disposer using one of
the following methods:
|. Disconnect power. . . . .
mH Option 1, Waste disposer — with air gap
2. Turn off water supply.
Option 2, No waste disposer — with air gap a
Pre m Option 3, Waste disposer — no air gap*
gb ae
a Option 4, No waste disposer — no air gap*
*An air gap is recommended.
Helpful Tip: To reduce the vibration of the hose, keep the hose
dishwasher in an existing cabinet opening with utility hookups.
away from the floor and the edge of the hole where it passes
mg If you are installing the dishwasher in a cabinet opening that through the cabinet.
does not have hookups, follow the steps under “Prepare cabinet
opening where there are no existing utility hookups” section. Option 1, Waste disposer - with air gap:
' :
]. Remove the disposer knockout plug. Cut end of drain hose if
needed (do not cut ribbed section).
|. Check that the water
line reaches to the front
left of opening where
the water connection
will be made.
2. Attach drain hose to air gap with large spring-type clamp. If
the drain hose was cut, use a 1/2" to 2" (3.8 to 5 cm) screw-type
clamp*.
2. Check that the direct - 3. Use a rubber hose connector® with spring or screwtype clamps*
wire reaches to the 6" (15.2 ¢
front right of opening
where the electrical connection will be made.
to connect air gap to disposer inlet.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed.
If the water line and the direct wire reach far enough into the
opening, proceed to the next section “Install the drain hose.” If they
do not reach far enough, follow the steps under “Prepare cabinet
opening where there are no existing utility hookups.”
Drain hose -
cut here if needed
a Rubber hose
connector
ey!
Spring of
screw-type
clamps
Large
spring-type
clamp
Drain
hose
Drain trap
4. Insert drain hose through hole
Drain hose
cut in cabinet to the front
center of opening where
drain connection will be
made.
*Parts available from local
plumbing supply stores.

Option 2, No waste disposer - with air gap:
]. Cut end of drain hose if needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type clamp. If
the drain hose was cut, use a 11/2" to 2" (3.8 to 5 cm) screw-type
clamp*.
3. Use a rubber hose connector* with spring or screwtype clamps*
to connect air gap to waste tee.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed.
Drain hose -
cut here if needed
Rubber hose
connector
Air gap
Spring of
screw-type
clamps Large
spring-type
clamp
Drain
Drain trap hose
4. Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection
will be made.
*Parts available from local
plumbing supply stores.
Option 3, Waste disposer - no air gap:
J. Remove the disposer knockout plug. Do not cut end of drain
hose.
2. Attach drain hose to disposer inlet with large springtype clamp.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed. It
is recommended that the drain hose be looped up and securely
fastened to the underside of the counter.
Large spring-type
3. Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection will
be made.
Drain hose
Option 4, No waste disposer - no air gap:
]. Cut end of drain hose if needed (do not cut ribbed section).
2. Attach drain hose to waste tee with 142" to 2" (3.8 to 5 cm)
screw-type clamp*,.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed. It
is recommended that the drain hose be looped up and securely
fastened to the underside of the counter.
Drain hose -
cut here if needed
Screw-type
Drain
hose
Drain trap
3. Insert drain hose through hole
cut in cabinet to the front
center of opening where drain
connection will be made.
Drain hose
*Parts available from local
plumbing supply stores.
i,
Prepare cabinet opening where there are no
Electrical connection
Option 1, Direct wire method:
Helpful Tip: Wiring the dishwasher will be easier if you route
wire into the cabinet opening from the right side.
1. Drill a %4" (1.9 cm) hole in
right-hand cabinet side, rear
or floor. Preferred and
optional locations are shown.
2. Wood cabinet: Sand the hole
until smooth.
Preferred
locations
Optional
locations
Metal cabinet: Cover hole
with grommet, (Part Number 302797 - not provided.)
3. Run wire into house wiring junction box.
A. Install a UL Listed/CSA Approved clamp connector (strain
relief) for flexible-type wire. If installing conduit, attach a UL
Listed/CSA Approved strain relief to the junction box.
5. Run other end of wire
through cabinet hole. Cable
must extend to the right
front of cabinet opening.

Option 2, Power supply cord method:
NOTE: A mating, 3 prong, ground-type wall receptacle is required
in a cabinet next to the dishwasher opening.
1. Drill a 1%" (3.8 cm)
hole in the cabinet
Preferred
locations
Optional
locations
rear or side.
Preferred and
optional locations
are shown.
Wood cabinet:
Sand the hole until
smooth.
Metal cabinet: Cover hole with grommet (Part Number
302797) included with power supply cord kit.
Install the water line
Helpful Tip: Routing the water line through the left side of
cabinet opening will make water connection easier.
Drill a minimum ¥2" (1.3 cm) hole in the cabinet side, rear or
floor. Preferred and optional locations are shown.
Preferred
locations
Optional
locations
Measure overall length
of copper tubing
required.
Attach copper tubing
to the water line with a
manual shutoff valve.
Slowly feed copper
tubing through hole in
cabinet. Copper tubing will bend and kink easily, so be gentle.
The copper tubing should be far enough into the cabinet
opening to connect it to dishwasher inlet on the front left of the
dishwasher.
Turn water shutoff valve to “ON” position. Flush water into a
shallow pan to get rid of particles that may clog the inlet valve.
Turn shutoff valve to “OFF” position.
Install the drain hose
IMPORTANT: Always use a new drain hose.
Drill a 114%" (3.8 cm)
diameter hole in
cabinet wall or floor
on the side of the
opening closest to the
sink.
Connect drain hose to waste tee or waste disposer using one of
the following methods:
mH Option 1, Waste disposer — with air gap
mH Option 2, No waste disposer — with air gap
mB Option 3, Waste disposer — no air gap*
m Option 4, No waste disposer — no air gap*
*An air gap is recommended.
Helpful Tip: To reduce the vibration of the hose, keep the hose
away from the floor and the edge of the hole where it passes
through the cabinet.
Option 1, Waste disposer - with air gap:
1.
2.
A,
*Parts available from local
Remove the disposer knockout plug. Cut end of drain hose if
needed (do not cut ribbed section).
Attach drain hose to air gap with large spring-type clamp. If
the drain hose was cut, use a 1/2" to 2" (3.8 to 5 cm) screw-type
clamp*.
Use a rubber hose connector* with spring or screwtype clamps*
to connect air gap to disposer inlet.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed.
Drain hose -
cut here if needed
x Rubber hose
connector
Spring or
screw-type
clamps
Large
spring-type
clamp
Drain
hose
Drain trap
Insert drain hose through
hole cut in cabinet to the
Drain hose
front center of opening
where drain connection will
be made.
plumbing supply stores.

Option 2, No waste disposer - with air gap:
]. Cut end of drain hose if needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type clamp. If
the drain hose was cut, use a 11/2" to 2" (3.8 to 5 cm) screw-type
clamp*.
3. Use a rubber hose connector* with spring or screwtype clamps*
to connect air gap to waste tee.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed.
Drain hose -
cut here if needed
Rubber hose
connector
rf
Air gap
Spring or
screw-type
clamps
Large
spring-type
clamp
Drain
Drain trap hose
4, Insert drain hose through
hole cut in cabinet to the
Drain hose
front center of opening
where drain connection will
be made.
*Parts available from local
plumbing supply stores.
Option 3, Waste disposer - no air gap:
J. Remove the disposer knockout plug. Do not cut end of drain
hose.
2. Attach drain hose to disposer inlet with large springtype clamp.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed. It
is recommended that the drain hose be looped up and securely
fastened to the underside of the counter.
3. Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection will
Drain hose
be made.
Option 4, No waste disposer - no air gap:
]. Cut end of drain hose if needed (do not cut ribbed section).
2. Attach drain hose to waste tee with 1/2" to 2" (3.8 to 5 cm)
screw-type clamp*.
This connection must be before the drain trap and at least 20"
(50.8 cm) above the floor where dishwasher will be installed. It
is recommended that the drain hose be looped up and securely
fastened to the underside of the counter.
Drain hose -
cut here if needed
Screw-type
clamp
Drain trap
3. Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection will
be made.
*Parts available from local
plumbing supply stores.
%
x , 9 ao bene, & mo be ens
Prepare Dishwasher
AWARNING
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
AWARNING
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Helpful Tip: Put cardboard under dishwasher until it is installed
in cabinet opening. The cardboard will help avoid damage to
floor covering during installation.
as Using 2 or more people, grasp the sides of dishwasher door
frame and put the dishwasher on its back, resting on top of the
corner posts.
N Remove two screws attaching access panel and lower panel to
dishwasher using a Y4" hex socket, nut driver or Phillips
screwdriver.
o

3. Remove panels and set panels aside on a covered surface.
4. Check that grounding clip is attached to the lower panel.
panel
Grounding
clip
5. Slide nut and ferrule onto tubing.
Copper tubing only: Slide nut, then ferrule, about 1" (2.5 cm)
onto copper tubing.
NOTE: To avoid vibration during operation, route the water
supply line so that it does not touch the dishwasher base, frame
or motor.
6. Add 90° elbow fitting to the water supply line.
Connect the 98" compression fitting to the water supply line
prior to installing the unit into the cabinet opening. Attach such
that the ¥4" connection is facing upward.
Copper tubing only: Put the tubing into the 90° elbow fitting as
far as it will go (the copper tubing bends and kinks easily).
Slide the nut and ferrule forward and start the nut onto the
elbow threads. Flexible braided connection: Secure nut to
elbow using ¥8" open ended wrench or adjustable wrench.
NOTE: Do not use Teflon® tape with compression fittings.
7. Remove terminal box cover.
— If you are direct wiring: Install a UL Listed/CSA Approved
clamp connector to the terminal box. If using conduit, use a
UL Listed /CSA Approved strain relief.
— If you are installing a power supply cord kit, do so now,
following kit instructions. The power supply cord kit must be
UL Listed and marked for use with dishwashers (that is, Power
Supply Cord Kit Part Number 4317824).
7®Teflon is a registered trademark of E.l. Du Pont de Nemours and Company.
10
Terminal
cv box cover
Pe ie
PER \
&
Deeks ou
Cable clamp
connector
Dishwasher wires
8. Measure height of cabinet opening
from underside of countertop to
floor where dishwasher will be ~~] —_
installed (you need the lowest —
point). Check chart for that height
opening. Put wheels in the required
position. — Vv [——
Minimum Wheel Number of
cutout height | position front fe
g
34" (86.4 cm) 1 10
341%" (87 cm) 2 5
34'4" (87.6 cm) 3 0
dishwasher to fit into a 337" (86 cm) high
cutout, but the dishwasher will be more
9. Turn both front leveler legs to the same
height. ®
If the minimum cutout height is less than 34"
(86.4 cm), the rear wheels can be removed
for additional clearance. This will allow the
Front leg
difficult to move into position. If the wheels
are removed, cover the floor when moving the dishwasher.
If you have built-up floors
]. Measure height of opening
from underside of countertop VA
to built-up floor. If the height TF
Countertop
is at least 3394" (85.7 cm),
the dishwasher will fit into the
opening without modification
to the countertop or flooring.
2. Put wheels in position 1 and
turn the front leveler legs up
all the way.
3. Add shims as needed in the
area shown to bring
dishwasher up to proper height.
NOTE: Shims must be securely attached to the floor to keep
them from moving when the dishwasher is operating.
6" 25/4"
(700m) (15.2 cm)