Kenmore 253.6011 Series User manual

Use & Care Guide
Manual de Uso y Cuidado
Guide d%tilisafion et d%ntrefien
English /Espa_ol /Fran_ais
Modets/Modelos/Mod_les: 253.6000%6002%6008%6011%6030%6031 _
6038%6040%6041%6050%6060%6062%7030%7040%7050%7060%
7062%706Y
Ke
Refriger®dor Superior
R6frig6r®teur @comp®rHments superpos6s
::::::::::Coot I_umlse_} n@sero de co_o10 le I_um6ro de couleur
P/N A01265001 (1406)
Sears Brands Management Corporation
Hof_man Estates, IL 60179 U.S.A.
www.kenmore.com
www.sears.com
Sears Canada Inc.
Toronto, Ontario, Canada M5B 2C3
www.sears.ca
All manuals and user guides at all-guides.com
all-guides.com

Record Model/Serial
Numbers
Please read and save these
instructians
This Use & Care Guide provides specific
operating instructions for your model.
Use your unit only as instructed in this
guide. These instructions are not meant
to cover every possible condition and
situation that may occur. Common sense
and caution must be practiced when
installing, operating, and maintaining any
appliance.
Please record your model and serial
numbers below for future reference.
This information is found on the serial
plate located inside the refrigerator
compartment.
Model Number: 253.
Serial Number:
Purchase Date:
IMPORTANT
Use only soap and water to clean serial
plate.
Table of Contents
Record Model/Serial Numbers................ 2
Important Safety instructions ............... 2-4
Warranty Information ............................ 5
Master ProtectionAgreements ................ 6
Featuresat a Glance.............................. 7
First Steps....................................... 8-14
Connecting the Water Supply................. 15
Setting the Temperature Control ............ 16
Optionaa Features........................... 18-19
FoodStorage and
Energy-SavingIdeas........................ 20
ice Service.......................................... 21
Normal Operating Sounds.................... 22
Careg Cleaning ............................. 23-25
Before YouCall .............................. 26-28
Service Numbers...................... BackCover
Important Safety
Instructions
Safety Precautians
Do not attempt to install or operate
your unit until you have read the safety
precautions in this manual. Safety items
throughout this manual are labeled with
a Danger, Warning, or Caution based on
the risk type.
Definltlans
_This is the safety alert symbol. It is
used to alert you to potential personal
injury hazards. Obey all safety messages
that follow this symbol to avoid possible
injury or death.
DANGER
DANGER indicatesan imminently
hazardous situation which, if not
avoided, witi resultin death or serious
injury.
_WARNING
WARNING indicatesapotentially
hazardous situationwhich, if notavoided,
could resultin death or seriousinjury.
CAUTION
CAUTION indicatesapotentially
hazardoussituation which, if notavoided,
may resultin minoror moderate injury.
IMPORTANT
Indicates installation, operation, or
maintenance information which is
important but not hazard=related.
All manuals and user guides at all-guides.com

important Safety Instructions
_WARNING
Please read all safety instructions
before using your new appliance.
For Your Safety
*Do not store or use gasoline or other
flammable liquids in the vicinity of
this or any other appliance. Read
product labels for warnings regarding
flammability and other hazards.
*Do not operate the unit in the presence
of explosive fumes.
*Avoid contact with any moving parts of
automatic ice maker°
*Remove all staples from the carton.
Staples can cause severe cuts and also
destroy finishes if they come in contact
with other appliances or furniture.
Child Safety
Destroy or recycle the carton, plastic
bags, and any exterior wrapping material
immediately after the unit is unpacked.
Children should never use these items
to play. Cartons covered with rugs,
bedspreads, plastic sheets or stretch wrap
may become airtight chambers and can
quickly cause suffocation.
Proper dlsposal of your appliance
Risk of child entrapment
Child entrapment and suffocation are
not problems of the past. Junked or
abandoned appliances are still dangerous
- even if they will sit for "just a few days."
If you are getting rid of your appliance,
please follow the instructions below to
help prevent accidents.
Dispose of refrigerator in accordance with
Federal and Local regulations. Before you
throw away your old unit:
*Remove doors.
"Leave shelves in place so children may
not easily climb inside.
*Refrigerants must be evacuated by
a licensed, EPA certified refrigerant
technician in accordance with
established procedures.
_WARNING
These guidelines must be followed to
ensure that safety mechanisms in this
unit will operate properly.
Electrical information
*The refrigerator must be plugged into
its own dedicated 10 amp, 115 Volt, 60
Hz. AC only electric outlet. The power
cord of the appliance is equipped
with a three-prong grounding plug
for your protection against shock
hazards. It must be plugged directly
into a properly grounded three-prong
receptacle. The receptacle must be
installed in accordance with local codes
and ordinances. Consult a qualified
electrician. Do not use an extension
cord or adapter plug.
*Immediately repair or replace any
power cord that becomes frayed or
damaged.
All manuals and user guides at all-guides.com

important Safety Instructions
*Never unplug the refrigerator by pulling
on the power cord. Always grip the
plug firmly, and pull straight out from
the receptacle to prevent damaging the
power cord.
*Unplug the refrigerator before cleaning
and before replacing a light bulb to
avoid electrical shock.
*Performance may be affected if
the voltage varies by 10% or more.
Operating the unit with insufficient
power can damage the motor. Such
damage is not covered under the
warranty. If you suspect your household
voltage is high or low, consult your
power company for testing.
*Do not plug the unit into an outlet
controlled by a wall switch or pull cord
to prevent the refrigerator from being
turned off accidentally.
*Avoid connecting refrigerator to a
Ground Fault Circuit Interruptor (GFCI).
Grounding type wall receptacle
Do not, under any
circumstances, cut,
remove, or bypass the
grounding prong
Power cord with 3:prong
iMPORTANT
CFC/HCFC Disposal
Your old refrigerator may have
a cooling system that used CFCs
or HCFCs (chlorofiuorocarbons or
hydrochlorofiuorocarbons). CFCs
and HCFCs are believed to harm
stratospheric ozone if released to the
atmosphere. Other refrigerants may
also cause harm to the environment if
released to the atmosphere.
If you are throwing away your old
refrigerator, make sure the refrigerant
is removed for proper disposal by a
qualified technician. If you intentionally
release refrigerant, you may be subject
to fines and imprisonment under
provisions of environmental legislation.
All manuals and user guides at all-guides.com

Warranty Information
I(ENMORE LIMITED WARRANTY
FOR ONE YEAR from the date of sale this appliance is warranted against defects in
material or workmanship when it is installed, operated and maintained according to all
supplied instructions.
WITH PROOF OF SALE, a defective product will receive free repair or replacement at
option of seller. To arrange for warranty service, call 1-800-4-MY-HOME ®
If this appliance is ever used for other than private family purposes, this warranty applies
for only 90 days from sale date in the United States, and is void in Canada.
This warranty covers ONLY defects in material and workmanship, and
will NOT pay for:
1. Expendable items that can wear out from normal use, including but not limited to
filters, belts, bags and screw-in base light bulbs.
2. A service technician to instruct the user in correct product installation, operation
or maintenance.
3. A service technician to clean or maintain this product.
4. Damage to or failure of this product if it is not installed, operated or maintained
according to all instructions supplied with the product.
5. Damage to or failure of this product resulting from accident, abuse, misuse or use
for other than its intended purpose.
6. Damage to or failure of this product caused by the use of detergents, cleaners,
chemicals or utensils other than those recommended in all instructions supplied with
the product.
7. Damage to or failure of parts or systems resulting from unauthorized modifications
made to this product.
Disclaimer of implied warranties; limitation of remedies
Customer's sole and exclusive remedy under this limited warranty shall be product repair as
provided herein. Implied warranties, including warranties of merchantability or fitness for
a particular purpose, are limited to one year or the shortest period allowed by law. Sears
shall not be liable for incidental or consequential damages. Some states and provinces do
not allow the exclusion or limitation of incidental or consequential damages, or limitation
on the duration of implied warranties of merchantability or fitness, so these exclusions or
limitations may not apply to you.
This warranty applies only while this appliance is used in the United States or Canada _.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
In-home repair service is not available in all Canadian geographical areas, nor will this
warranty cover user or servicer travel and transportation expenses if this product is located in a
remote area (as defined by Sears Canada Inc.) where an authorized servicer is not available.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
Sears Canada Inc., Toronto, Ontario, Canada M5B 2C3
All manuals and user guides at all-guides.com

Master Protection Agreements
Congratulations on making a smart purchase. Your new Kenmore ® product is designed
and manufactured for years of dependable operation. But like all products, it may require
preventive maintenance or repair from time to time. That's when having a Master Protection
Agreement can save you money and aggravation.
The Master Protection Agreement also helps extend the life of your new product. Herds what
the Agreement _ includes:
*Parts and labor needed to help keep products operating properly under normal
use, not just defects. Our coverage goes well beyond the product warranty. No
deductibles, no functional failure excluded from coverage -real protection.
*Expert service by a force of more than 10,000 authorized Sears service technicians,
which means someone you can trust will be working on your product.
*Unlimited service calls and nationwide service, as often as you want us, whenever
you want us.
* "No-lemon" guarantee - replacement of your covered product if four or more
product failures occur within twelve months.
*Product replacement if your covered product can not be fixed.
*Annual Preventive Maintenance Check at your request - no extra charge.
*Fast help by phone - we call it Rapid Resolution - phone support from a Sears
representative on all products. Think of us as a °'talking ownePs manual".
*Power surge protection against electrical damage due to power fluctuations.
*$250 Food Loss Protection annually for any food spoilage that is the result of
mechanical failure of any covered refrigerator or freezer.
*Rental reimbursement if repair of your covered product takes longer than promised.
*25% discount off the regular price of any non-covered repair service and related
installed parts.
Once you purchase the Agreement, a simple phone call isall that it takes for you to schedule
service. Youcan call anytime day or night,or schedule a service appointment online.
TheMaster Protection Agreement isa riskfree purchase. If you cancel for any reasonduring
the product warranty period, we will provide a full refund.Or, a prorated refundanytime after
the product warranty period expires. Purchaseyour Master ProtectionAgreement today!
Some limitationsand exclusionsapply. Forprices and additional information inthe U.S.A.call
1-800-827-6655.
_ Coverage in Canada varies on some items. For full details call Sears Canada at 1-800-361-
6665.
Sears Installation Service
For Sears professional installation of home appliances, garage door openers, water heaters,
and other major home items, in the U.S.A. or Canada call 1-800-4-MY-HOME ®.
All manuals and user guides at all-guides.com
all-guides.com

Features At A Glance
Features may vary according to model
Ice Bucket
Freezer
Auxiliary Freezer
Control
Refrigerator
Control
(Some Models)
Dell Cover
Dell Drawer
Half Shelf
Full Shelf
Mid-level..
Light"
Dell Cover
Dell
Crisper
Cover
Cris
Drawers
Ice Tray Light
i ii iI
Toe Grille
Fixed Door
Bin
Door Rack
Dairy Door
Tall Bottle
Retainer
Door Bin
Fixed
Door Bin
Door Rack
IMPORTANT
Cleaning your Refrigerator
Remove tape and glue residue from surfaces before turning on the refrigerator. Rub
asmall amount of liquid dish soap over the adhesive with your fingers. Rinse with
warm water and dry with a soft cloth.
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners
to remove tape or glue. These products can damage the surface of your refrigerator.
After you remove all of the package materials, clean the inside of your refrigerator
before using it. See the "Care & Cleaning" section in this manual.
See important information about cleaning glass shelves and covers in the "Optional
Features" section of this manual.
IMPORTANT
Moving your Refrigerator
Your refrigerator is heavy. When moving the refrigerator for cleaning or service_
be sure to cover the floor with cardboard or hardboard to avoid floor damage.
Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the
refrigerator when trying to move it as floor damage could occur.
All manuals and user guides at all-guides.com

First Steps
This Use & Care Guide provides general
operating instructions for your model. Use
the refrigerator only as instructed in this
Use & Care Guide. Before starting the
refrigerator, follow these important first
steps.
Location
*Choose a place that is near a grounded
electrical outlet. Do Not use an
extension cord or an adapter plug.
*If possible, place the refrigerator out
of direct sunlight and away from the
range, dishwasher or other heat sources.
The refrigerator must be installed on a
floor that is level and strong enough to
support a fully loaded refrigerator.
Consider water supply availability for
models equipped with an automatic ice
maker. If you do not hook up water to
the refrigerator, remember to turn the
ice maker off.
CAUTION
Do Not install the refrigerator where
the temperature will drop below 55°F
(13°C) or rise above 110°F (43°C).
The compressor will not be able to
maintain proper temperatures inside
the refrigerator.
Do Not block the toe grille on the lower
front of your refrigerator. Sumcient air
circulation is essential for the proper
operation of your refrigerator.
NOTE
If your refrigerator is placed with the
door hinge side against a wall, you may
have to allow additional space so the
door can be opened wider.
Guidelines for final positioning of your
refrigerator:
*All four corners of the cabinet must rest
firmly on the floor.
*The cabinet should be level at the front
and rear.
*The sides should tilt 1/4-inch (6 mm)
from front-to-back (to ensure that doors
close and seal properly).
Doors should align with each other and
be level.
To install the toe grille:
1. Attach toe grille support bracket to
cabinet using 3 bolts supplied.
2. Install left toe grille cover onto slot on
left side of toe grille.
Installation
Installation clearances "--_.__.
*Allow the following clearances _
for ease of installation, proper air -'"
circulation, and plumbing and electrical
connections:
Sides & Top 3/8 inch "..
Back 1 inch
All manuals and user guides at all-guides.com

First Steps
3. Attach toe grille to cabinet.
or
some models
To level the cabinet using the front rollers:
1 Remove the toe grille.
2 Use a flat-blade screwdriver or 3/8
inch socket wrench to raise or lower
the front rollers (Figure 2).
!ii i!iill
i iiii
Figure 2
or
Use adjustable wrench to adjust leveling
screws. Lower the leveling screws on each
side clockwise until they contact the floor
(Figure 3).
Raise
Figure 3
NOTE
Raise the front of the refrigerator enough
so the doors close freely when opened
halfway. The refrigerator should slope t/4
inch to 1/2 inch from front-to-bacl<. Then
level the refrigerator from side-to-side.
4 Some models are equipped with an anti-
tip bracket (Figure 4). Lower it clockwise
until it contacts the floor.
Figure 4 (some models)
_WARNING
The anti=tip device must be
installed according to the
instructions in your Use &
Care Manuel. Failure to do
so will result in in'ur .
_WARNING
When reversing the door swing:
You MUST move the anti=tip bracket
to align with the hinges of the door.
Failure to do so wiii result in injury.
All manuals and user guides at all-guides.com

First Steps
Tools Necessary:
or
oF
Phillips TM Head Socket WrenchSet
Top Hinge _ _f_,Top Hinge
Cover Front k.,) _'_ZCover Rear
S.... _ L_ S....
_ Hinge Bottom
S.... Hinge
NOTE
The direction in which your refrigerator doors open (door swing) can be reversed,
from left to right or right to left, by moving the door hinges from one side to the other.
Reversing the door swing should be performed by a qualified person.
IMPORTANT
Before you begin, turn the refrigerator temperature control to "0" (OFF) and remove the electrical
power cord from the wall outlet. Remove any food from door shelves.
Door removal and reversat instructions: 4.
1.
2. 5.
Remove toe grille.
Remove top hinge cover. Trace around
the hinge with a soft lead pencil. This
makes reinstallation easier. Remove
top hinge and lift door oft: center
hinge pin. Set door aside.
Tap
Hinge
Cover
)Top Hinge
3. Unscrew center hinge pin using adjustable
wrench and save for reassembly. Ensure
plastic washer stays on hinge pin. 10
6.
Lift refrigerator door off of bottom
hinge and set aside.
Remove center hinge and shim by
removing inside screw and loosening two
outside screws enough to allow hinge
and shim to slide out. Tighten screws.
Loosen two outside screws on
opposite side of refrigerator° remove
inside screw and install center hinge.
Door
_sher
!nge
Center
{inge
'Screws
Handle
Hole
Plug
;J
All manuals and user guides at all-guides.com

First Steps
7. Remove three screws on bottom hinge
and anti-tip bracket (if equipped)
with 3/8" socket wrench.
8. Install bottom hinge and anti-tip bracket
(if equipped) on opposite side with the
three screws removed from step 7.
9. Unscrew bottom hinge pin using adjustable
wrench. Move hinge pin to other hole in
hinge and tighten with adjustable wrench.
10. Reverse door handles (see Handle
Installation section).
11. Move freezer and refrigerator door
stops to opposite side. Before starting
screws, use an awl to puncture the foam.
12. Position refrigerator door onto bottom
hinge pin and screw center hinge pin
through center hinge intotop of door. Close
refrigerator door to help align hinge hole.
13. Tighten center hinge pin with
adjustable wrench.
14. Remove cabinet and hinge hole plugs
and move to opposite side.
15. Lower freezer door onto center hinge pin.
16. Close freezer door. Have an assistant
lift up on opposite side of door while
tightening screws to install top hinge.
17. There are two toe grille covers
provided in your literature packet; one
for the right side and one for the left
side. Install the appropriate cover over
the opening on the side opposite the
anti-tip bracket, (see Figures A & B).
NOTE
In case of future door reversals, save
the toe grille cover not being used.
18. Flip toe grille and reinstall (some models).
19. Plug inelectrical power cord and turn
refrigerator temperature control to center
position. Adjust setting as necessary.
_WARNING
When reversing the door swing:
You MUST move the anti=tip bracket
to align with the hinges of the door.
Failure to do so will result in injury.
Door Stop .Door
Stop
_Screv_s
Toe
Grille
Grille
Support
Toe Grille Cover A
_/ _ Toe Grille
I-" _ ._l/I Support
i! .._._. _r-zJ_/ToeGrille
ii _/_./'_..¢':Y% Cover
BrackPt
All manuals and user guides at all-guides.com
all-guides.com

First Steps
Handle Installation/Removal
iMPORTANT
There are instructions for three (3) handle
styles on the following pages. Toensure
proper installation of all three handle
styles, review these instructionsand pictures
thoroughly prior to handle installation.
Additionally, before installing handles,
make sure the door swing is correct. See
the Door Removal/Reversal instructions in
this Use & Care Guide.
CAUTION
Wear gloves and use extreme CAUTION
when installing these handles. The rounded
end of the handles may be sharp.
Handle Style 1
To remove refrigerator handle:
(Handles may be easier to reverse while
doors are off.)
1. Remove two screws attaching handle
to top of refrigerator door.
2. Slide handle straight up and pull
handle off mounting screw on door.
3. Remove mounting screw from door
and install on other side, moving hole
plugs from corresponding holes to
opposite side.
To attach refrigerator handle:
1. Place top of handle over mounting
scre% pull handle straight down until
handle is aligned with screw holes on
top of door.
2. Secure top of handle with two screws
removed earlier.
Button
Plug
Mounting Screw
To remove freezer handle:
(Handles may be easier to reverse while
doors are off.)
1. Remove two screws attaching handle
to bottom of freezer door.
2. Slide handle straight down and pull
handle off mounting screw on door.
3. Remove mounting screw from door
and install on other side, moving hole
plugs from corresponding holes to
opposite side.
4. Self=Adhesive Nameplate Models..
Use plastic putty knife to gently peel
off nameplate from door and reapply
over old holes.
To attach freezer handle:
1. Place top of handle over mounting
scre% pull handle straight up until
handle is aligned with screw holes on
bottom of door.
2. Secure bottom of handle with two
screws removed earlier.
Lock Handle
4 OverM0unting
Screw Screw
To reverse refrigerator/freezer handles:
Handles may be easier to reverse while
doors are off:.
Reverse freezer
and refrigerator
handles by
inverting the
handle removed
from the
refrigerator door
and attaching to
the freezer door.
nvert the handle
removed from
freezer door
and attach to
the refrigerator
door.
All manuals and user guides at all-guides.com

First Steps
Handle Style 2
To remove refrigerator metal handle:
1. Loosen the set screw on the rounded
part of the handle.
2. Remove the 2 screws from the top of
the handle.
3. Remove rounded part of handle from
mounting screw on face of door.
To attach refrigerator metal handle:
1. Place rounded part of handle onto
mounting screw on face of door and
align the 2 holes in top of handle with
the 2 holes in top of door. Handle
should be mounted with set screw
facing towards center of door. Do not
tighten the set screw yet.
2. Install the 2 screws into the top of the
handle.
3. Tighten the set screw on the rounded
part of the handle until the handle is
flush with the door, and then tighten
another 1/2turn.
-Handle
Button
Plug
To remove freezer handle:
1. Loosen the set screw on the rounded
part of the handle.
2. Remove the 2 screws from the bottom
of the handle.
3. Remove rounded part of handle from
mounting screw on face of door.
To attach freezer handle:
1. Place rounded part of handle onto
mounting screw on face of door and
align the 2 holes in bottom of handle
with the 2 holes in bottom of door.
Handle should be mounted with set
screw facing towards center of door.
Do not tighten the set screw yet.
2. Install the 2 screws into the bottom of
the handle.
3. Tighten the set screw on the rounded
part of the handle until the handle is
flush with the door, and then tighten
another 1/2turn.
J
Screw
r- Set Nameplate
J Screw S
Screw
To reverse refrigerator,/freezer handles:
Handles may be easier to reverse while
doors are off,
Reverse freezer
and refrigerator
handles by
inverting the
handle removed
from the
refrigerator door
and attaching
to the freezer
door. Invert the
handle removed
from freezer door and attach to the
refrigerator door.
13
All manuals and user guides at all-guides.com

First Steps
Handle Style 3
To remove refrigerator handle:
(Handles may be easier to reverse while
doors are off.)
1. Remove two screws attaching handle
to top of refrigerator door.
2. Slide handle straight up and pull
handle off mounting screw on door.
3. Remove mounting screw from door
and install on other side, moving hole
plugs from corresponding holes to
opposite side.
To attach refrigerator handle:
1. Place top of handle over mounting
screw; pull handle straight down until
handle is aligned with screw holes on
top of door.
2. Secure top of handle with two screws
removed earlier.
/
/
To remove freezer handle:
To attach freezer handle:
1. Place top of handle over mounting
screw; pull handle straight up until
handle is aligned with screw holes on
bottom of door.
2. Secure bottom of handle with two screws
removed earlier.
A_
f
J
J
J
J
J
J
J
J
J
J
J
J
J
J
To reverse refrigerator/freezer handles:
Handles may be easier to reverse while
doors are off.
Reverse freezer and refrigerator handles
by inverting the handle removed from the
refrigerator door and attaching to the
freezer door. Invert the handle removed
from freezer door and attach to the
refrigerator door.
(Handles may be easier to reverse while
doors are off.)
1. Remove two screws attaching handle
to bottom of freezer door.
2. Slide handle straight down and pull
handle off mounting screw on door.
3. Remove mounting screw from door
and install on other side, moving hole
plugs from corresponding holes to
opposite side.
4. Self-Adhesive Nameplate Models:
Use plastic putty knife to gently peel
off nameplate from door and reapply
over old holes. 14
All manuals and user guides at all-guides.com

Connecting Household Water Supply To Refrigerator
_WARNING
To avoid electric shock, which can
cause death or severe personal injury,
disconnect the refrigerator from
electrical power before connecting a
water supply line to the refrigerator.
CAUTION
To Avoid Property Damage:
* Copper tubing is recommended for the
water supply line. Water supply tubing
made of 1¼- plastic isnot recommended
since it greatly increases the potential for
water leaks. Manufacturer nor retailer
will be responsible for any damage if
plastic tubing isused for supply line.
" DO NOT install water supply tubing
in areas where temperatures fall
below freezing.
* Chemicals from a malfunctioning
softener can damage the ice maker.
if the ice maker is connected to soft
water, ensure that the softener is
maintained and working properly.
IMPORTANT
Ensurethat your water supply line connections 8.
comply with all local plumbing codes.
Before Installing The Water Supply 9.
Line, You Will Need:
*Basic Tools: adjustable wrench, flat=blade 10.
screwdriver, and Phillips screwdriver
*Access to a household cold water line with
water pressure between 30 and 100 psi.
*Awater supply line made of t/4" (6.4 ram)
OD, copper tubing. To determine the length
of copper tubing needed, you will need to
measure the distance from the ice maker inlet
valve at the back of the refrigerator to your
cold water pipe. Then add approximately 7
feet (2.1meters), so the refrigerator can be
moved out for cleaning (as shown).
"A shutoff valve to connect the water supply
line to your household water system. DO
NOT use a self-piercing type shutoff valve.
*Do not re-use compression fitting or use
thread seal tape.
*A compression nut and ferrule (sleeve)
for connecting the water supply line to
the ice maker inlet valve.
NOTE
Awater line kit isavailable from Sears stores
or Sears Parts & Repair at an additional cost.
To Connect Water Supply Line To
Ice Maker Inlet Valve:
1. Disconnect refrigerator from electric
power source.
2. Place end of water supply line into sink
or bucket. Turn ON water supply and
flush supply line until water is clear. Turn
OFF water supply at shutoff valve.
3. Unscrew plastic cap from water valve
inlet and discard cap.
4. Slide brass compression nut, and then
ferrule (sleeve) onto water supply line,
as shown.
5. Push water supply line into water valve
inlet as far as it will go (t/4"). Slide
ferrule (sleeve) into valve inlet and
finger tighten compression nut onto
valve. Tighten another half turn with a
wrench; DO NOT overtighten.
6. With steel clamp and screw, secure
water supply line to rear panel of
refrigerator as shown.
Z Coil excess water supply line (about 21/2
turns) behind refrigerator as shown and
arrange coils so they do not vibrate or
wear against any other surface.
Turn ON water supply at shutoff valve
and tighten any connections that leak.
Reconnect refrigerator to electrical
power source.
To turn ice maker on, lower wire signal
arm (see ice maker front cover for ON!
OFF position of arm).
Plastic Water
Tubing to
Maker Fill mp
Brass
3ression
Nut
Ferrule
ne
__ ater
Valve
Bracket
Valve Inlet
Water Valve
15
Water Supply
dnclude enough tubing in loop to allow
moving refrigerator out for cleaning.)
All manuals and user guides at all-guides.com

Setting the Temperature Controls
Cool Down Period
To ensure safe food storage, allow the
refrigerator to operate with the doors closed
for at least 8 hours before loading it with food.
Refrigerator &Freezer Controls
some models)
NOTE
When first turning
refrigerator on, adjust
the refrigerator control
to Normal. This is the
recommended initial
seffing. After 24 hours,
adjust the controls
as needed.
NOTE
If your unit is
in a garage or
area where the
temperature
is below 55 °,
adjust the freezer
control to the
coldest setting.
Cool Down Period
To ensure safe food storage, allow the
refrigerator to operate with the doors closed
for at least 8 hours before loading it with food.
Refrigerator &Freezer Controls
(some models)
NOTE
When first turning refrigerator on,
adjust control to Normal. This is the
recommended initial setting. After 24
hours, adjust the controls as needed.
i
temperature
garage coldest
cold
off
* recommended
Allow 24 hrs for adjustments
Refrigerator/Freezer Control
Temperature Adjustment
*Adjust temperature gradually: adjust the
knob in small increments, allowing the
temperature to stabilize.
*For colder temperatures, adjust the
knob towards Colder.
*For warmer temperatures, adjust the
knob towards Cold.
Adjusting the refrigerator/freezer
control will change temperatures in both
compartments. The auxiliary freezer control
can be left at the factory pre-set (Normal)
or adjusted as desired; it has no effect on
electrical power to the refrigerator.
To maintain temperatures, a fan circulates
air in the refrigerator and freezer
compartments. For good circulation, do
not block cold air vents with food items.
--q .........................................T----
AuxiliaryFreezer Control
All manuals and user guides at all-guides.com
all-guides.com

Setting the Temperature Controls
f/...................................... i
temperature
i c°ldest _
i! cold
off
* recommended
\ .................................... ./
IMPORTANT
Adjusting the refrigepator/freezer temperature
control to "0" turns off the compressor and
prevents the refrigerator from cooling, but does
not disconnect the power to the light bulb and
other electrical component& To turn off power
to your refrigerator r you must unplug the power
cord from the wall outlet.
Refrigerator/Freezer Control
Temperature Adjustment
*Adjust temperature gradually: adjust the
knob in small increments, allowing the
temperature to stabilize.
Adjusting the refrigerator/freezer
control will change temperatures in both
compartments. The auxiliary freezer
control can be left at the factory pre-
set (Normal) or adjusted as desired; it
has no effect on electrical power to the
refrigerator.
To maintain temperatures, a fan circulates
air in the refrigerator and freezer
compartments. For good circulation, do
not block cold air vents with food items.
17
All manuals and user guides at all-guides.com

Optional Features
_CAUTION
Do not cleon gloss shelves or covers
with warm water when they are
cold. Shelves and covers may break
if exposed to sudden temperature
changes or impact, such as bumping.
Tempered glass is designed to shatter
into many small, pebble=size pieces.
This is normal. Glass shelves and
covers ore heavy. Use both hands when
removing them to avoid dropping.
Shelf Adjustment
Refrigerator shelves are easily adjusted to
suit individual needs. Before adjusting the
shelves, remove all food.
To adjust sliding shelves:
1. Remove shelf by pulling forward to
stop position.
2. Lift front edge up and pull out.
To replace shelf, rest side edges on any
pair of shelf rails and carefully push shelf
back into position.
Door storage
Door bins, shelves, and racks are provided
for convenient storage of jars, bottles,
and cans. Frequently used items can be
quickly selected.
The dairy compartment, which is warmer
than the general food storage section, is
intended for short term storage of cheese,
spreads, or butter.
Adjustable door rack
Some models have door racks or bins that
can accommodate gallon-sized plastic
drink containers and economy-sized jars
and containers. Some racks are adjustable
for maximum storage capacity.
To remove door rack:
1. Push on rack sides to release from
locking tabs.
2. Pull straight out.
To install door rack:
1. Push rack straight ahead.
2. You will hear the sides lock into the
tabs,
Door Rack
Sliding Wire Shelf 18
All manuals and user guides at all-guides.com

Optional Features
Adjustable door bins
Some models have adjustable door bins
that can be moved to suit individual needs.
To move door bins:
1. Lift bin straight up.
2. Remove bin.
3. Place bin in desired position.
4. Lower bin onto supports until locked
in place.
CrisperHumidity Control(some models)
The crisper humidity control, present on the
crisper drawers of some models, allows you
to adjust the humidity within the crisper.
This can extend the life of fresh vegetables
that keep best in high humidity.
Low
Humidib
"_High
NOTE
Leafy vegetables keep best when stored
with the Humidity Control set on High
Humidity, or in a drawer without a
Humidity Control. This keeps incoming
air to a minimum and maintains
maximum moisture content. Store non-
leafy vegetables and fruits still in their
skins at the low humidity setting.
Pantry Drawer (some models)
Some
models are
equipped
with a
Pantry
Drawer for
storage of
luncheon
meats,
spreads,
cheeses,
and other deli items. Please be sure to
support glass when removing the drawer.
Crispers
(some
models)
The
crispers,
located
under the
bottom
refrigerator
shelf, are designed for storing fruits,
vegetables, and other fresh produce.
Wash items in clear water and remove
excess water before placing them in the
crispers. Items with strong odors or high
moisture content should be wrapped
before storing.
19
All manuals and user guides at all-guides.com

Food Storage & Energy Saving ideas
Food storage ideas
Fresh Food Storage
"The fresh food compartment should be
kept between 34°F and 40°F with an
optimum temperature of 37°F.
"Avoid overcrowding the refrigerator
shelves. This reduces the circulation
of air around the food and results in
uneven cooling.
Fruits and Vegetables
"Storage in the crisper drawers helps
preserve the fruit and vegetable quality
for longer time periods.
Meat
Raw meat and poultry should be
wrapped securely so leakage and
contamination of other foods or
surfaces does not occur.
Frozen Food Storage
*The freezer compartment should be kept
at O°F or lower.
*A freezer operates most efficiently when
it is at least 2/3 full.
Packaging Foods for Freezing
"To minimize dehydration and quality
deterioration, use aluminum foil,
freezer wrap, freezer bags or airtight
containers. Force as much air out of the
packages as possible and seal them
tightly. Trapped air can cause food to
dry out, change color, and develop an
off flavor (freezer burn).
*Wrap fresh meats and poultry with
suitable freezer wrap prior to freezing.
*Do not refreeze meat that has
completely thawed.
Loading the Freezer
,Avoid adding too much warm food to
the freezer at one time. This overloads
the freezer, slows the rate of freezing,
and can raise the temperature of frozen
hods.
Leave a space between the packages,
so cold air can circulate freely, allowing
food to freeze as quickly as possible.
Avoid storing hard-to-freeze foods such
as ice cream and orange juice on the
freezer door shelves. These foods are
best stored in the freezer interior where
the temperature varies less0
Energy saving ideas
*Locate the ,/_'_
refrigerator in
the coolest part
of the room, out
of direct sunlight,
and away from
heating products
or registers.
Do not place
the refrigerator next to heat-producing
appliances such as a range, oven, or
dishwasher. If this is not possible, a section
of cabinetry or an added layer of insulation
between the two appliances will help the
refrigerator operate more efficiently.
*Level the refrigerator so that the doors
close tightly.
*Refer to this Use & Care Manual for the
suggested temperature control settings.
*Periodic cleaning of the condenser
will help the refrigerator run more
efficiently. See the Care and Cleaning
Chart.
*Do not overcrowd the refrigerator or
block cold air vents located at upper
rear of refrigerator compartment. Doing
so causes the refrigerator to run longer
and use more energy.
*Cover foods and wipe containers dry
before placing them in the refrigerator.
This cuts down on moisture build-up
inside the unit.
Organize the refrigerator to reduce
door openings. Remove as many items
as needed at one time and close the
door as soon as possible.
20
All manuals and user guides at all-guides.com