Kenwood KDC-BT610U User manual

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
B5A-1337-00 (MN)© 2016 JVC KENWOOD Corporation
KDC-BT610U
KDC-BT510U
CD-RECEIVER
INSTRUCTION MANUAL
JS_KWD_KDC_BT610U_MN_C_1.indd 1JS_KWD_KDC_BT610U_MN_C_1.indd 1 22-Aug-16 12:10:27 PM22-Aug-16 12:10:27 PM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
2
BEFORE USE
IMPORTANT
• To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe
Warning and Caution in this manual.
• Please keep the manual in a safe and accessible place for future reference.
WARNING
• Do not operate any function that takes your attention away from safe driving.
• Do not ingest the battery, Chemical Burn Hazard
The remote control supplied with this product contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Caution
Volume setting:
•
Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
•
Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
• USB rating is indicated on the main unit. To view, detach the faceplate. ( 3)
• Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected
( 31) . Turn off the unit or change the source to STANDBY when parking at a low ceiling area.
Remote control (RC-406):
•
Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
How to read this manual
• Operations are explained mainly using buttons on the faceplate of .
• English indications are used for the purpose of explanation. You can select the display language from the [FUNCTION] menu. ( 5)
• [XX] indicates the selected items.
• ( XX) indicates references are available on the stated page.
CONTENTS
BEFORE USE 2
BASICS 3
GETTING STARTED 4
1 Select the display language
and cancel the demonstration
2 Set the clock and date
3 Set the initial settings
RADIO 6
AUX 7
CD/USB/iPod/ANDROID 8
Pandora® 10
BLUETOOTH® 11
AUDIO SETTINGS 18
DISPLAY SETTINGS 22
TROUBLESHOOTING 23
REFERENCES 25
Maintenance
More information
SPECIFICATIONS 28
INSTALLATION/
CONNECTION 29
ENGLISH
JS_KWD_KDC_BT610U_MN_EN_4.indd 2JS_KWD_KDC_BT610U_MN_EN_4.indd 2 26-Aug-16 5:20:47 PM26-Aug-16 5:20:47 PM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
3
BASICS
To On the faceplate On the remote control
Turn on the power Press .
• Press and hold to turn off the power.
Press and hold SRC to turn off the power.
( Pressing SRC does not turn on the power. )
Adjust the volume Turn the volume knob. Press or .
• Press and hold to continuously increase the
volume to 15.
Press ATT during playback to attenuate the sound.
• Press again to cancel.
Select a source Press repeatedly. Press SRC repeatedly.
Change the display information Press DISP repeatedly.
( 27) ( Not available )
Faceplate
How to resetAttach Detach
Remote control (RC-406) (supplied for )
ENGLISH
Display window
Pull out the insulation
sheet when using for the
first time.
How to replace the battery
Remote sensor (Do not expose to
bright sunlight.)
Volume
knob
Detach button
Loading
slot
: Remote control functions are not available.
: Flashes when the unit
enters searching status.
:
Lights up when
Bluetooth connection
is established.
( 12)
JS_KWD_KDC_BT610U_MN_EN_4.indd 3JS_KWD_KDC_BT610U_MN_EN_4.indd 3 26-Aug-16 5:20:48 PM26-Aug-16 5:20:48 PM

4
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
Select the display language and cancel the demonstration
When you turn on the power for the first time (or [FACTORY RESET] is
set to
[YES] , 5 ), the display shows: “SEL LANGUAGE” “PRESS”
“VOLUMEKNOB”
1 Turn the volume knob to select [ENG] (English) or [TUR] (Turkish),
then press the knob.
[ENG] is selected for the initial setup.
Then, the display shows: “CANCEL DEMO” “PRESS” “VOLUME
KNOB”.
2 Press the volume knob.
[YES] is selected for the initial setup.
3 Press the volume knob again.
“DEMO OFF” appears.
Then, the display shows the selected crossover type: “2-WAY X ’OVER” or
“3-WAY X ’ OVER”
• To change the crossover type, see “Change the crossover type”. ( 
5 )
Set the clock and date
1 Press the volume knob to enter
[FUNCTION] .
2 Turn the volume knob to select [CLOCK] , then press the knob.
1
2
To adjust the clock
3 Turn the volume knob to select [CLOCK ADJUST] , then press the knob.
4 Turn the volume knob to make the settings, then press the knob.
Hour Minute
5 Turn the volume knob to select [CLOCK FORMAT] , then press the knob.
6 Turn the volume knob to select [12H] or [24H] , then press the knob.
To set the date
7 Turn the volume knob to select [DATE FORMAT] , then press the knob.
8 Turn the volume knob to select [DD/MM/YY] or [MM/DD/YY] , then press
the knob.
9 Turn the volume knob to select [DATE SET] , then press the knob.
10 Turn the volume knob to make the settings, then press the knob.
Day Month Year or Month Day Year
11 Press and hold to exit.
To return to the previous setting item, press .
Set the initial settings
1 Press repeatedly to enter STANDBY.
2 Press the volume knob to enter [FUNCTION] .
3 Turn the volume knob to select an item (see the following table),
then press the knob.
4 Repeat step 3until the desired item is selected or activated.
5 Press and hold to exit.
To return to the previous setting item, press .
Default:
XX
AUDIO CONTROL
SWITCH
PREOUT
*
(For )
REAR / SUB-W : Selects whether rear speakers or a subwoofer are
connected to the line out terminals on the rear (through an external
amplifier).
( 31)
3
ENGLISH
JS_KWD_KDC_BT610U_MN_EN_4.indd 4JS_KWD_KDC_BT610U_MN_EN_4.indd 4 26-Aug-16 5:20:51 PM26-Aug-16 5:20:51 PM

ENGLISH 5
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
DISPLAY
EASY MENU
(For )
When entering
[FUNCTION] ...
ON :ZONE 1 illumination changes to white color.;
OFF :ZONE 1 illumination remains as [COLOR SELECT] color. ( 22)
• ZONE 2 illumination changes to white color when you enter [FUNCTION] ,
irregardless of the
[EASY MENU] setting.
• Refer to the illustration on page 22 for ZONE identification.
TUNER SETTING
PRESET TYPE NORMAL
:Memorizes one station for each preset button in each band (FM1/
FM2/FM3/AM/SW1/SW2).;
MIX :Memorizes one station for each preset button,
regardless of the selected band.
SYSTEM
KEY BEEP
*
ON :Activates the keypress tone.; OFF :Deactivates.
TDF ALARM
*
ON: Activates the alarm if you forget to detach the faceplate when ACC is set to OFF. ;
OFF: Deactivates.
SOURCE SELECT
PANDORA SRC ON
:Enables PANDORA in source selection.; OFF :Disables. ( 10)
BUILT-IN AUX ON
:Enables AUX in source selection.; OFF :Disables. ( 7)
CD READ 1
:Automatically distinguishes between audio file disc and music CD.;
2 :Forces to play as a music CD. No sound can be heard if an audio file disc is played.
F/W UPDATE
UPDATE SYSTEM
F/W UP xxxx YES
:Starts upgrading the firmware.; NO :Cancels (upgrading is not activated).
For details on how to update the firmware, visit <www.kenwood.com/cs/ce/>.
FACTORY RESET YES :Resets the settings to default (except the stored station).; NO :Cancels.
* Not applicable if 3-way crossover is selected.
CLOCK
CLOCK DISPLAY ON
:The clock time is shown on the display even when the
unit is turned off.;
OFF :Cancels.
ENGLISH
Select the display language for [FUNCTION] menu and music
information if applicable.
By default,
[ENGLISH] is selected.
TURKCE
Change the crossover type
1 Press repeatedly to enter STANDBY.
2 Press and hold number buttons 4and 5to enter crossover
select.
The current crossover type appears.
3 Turn the volume knob to select “2WAY” or “3WAY”, then
press the knob.
4 Turn the volume knob to select “YES” or “NO”, then press
the knob.
The selected crossover type appears.
• To cancel, press and hold .
• To adjust the selected crossover settings,
( 19, 20) .
Caution
Select a crossover type according to how the speakers are
connected. ( 
31 )
If you select a wrong type:
• The speakers may damage.
• The output sound level may be extremely high or low.
GETTING STARTED
JS_KWD_KDC_BT610U_MN_EN_4.indd 5JS_KWD_KDC_BT610U_MN_EN_4.indd 5 26-Aug-16 5:20:52 PM26-Aug-16 5:20:52 PM

6
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Other settings
1 Press the volume knob to enter
[FUNCTION] .
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
XX
TUNER SETTING
LOCAL SEEK ON
: Searches only AM/SW1/SW2 stations with good reception. ;
OFF : Cancels.
• Settings made are applicable only to the selected source/station. Once
you change the source/station, you need to make the settings again.
AUTO
MEMORY
YES :Automatically starts memorizing 6 stations with good reception.;
NO :Cancels.
• Selectable only if [NORMAL] is selected for [PRESET TYPE] . ( 5)
MONO SET ON
:Improves the FM reception, but the stereo effect may be lost.;
OFF :Cancels.
NEWS SET ON : The unit will temporarily switch to News Programme if available. ;
OFF :Cancels.
REGIONAL ON : Switches to another station only in the specific region using the “AF”
control.;
OFF :Cancels.
AF SET ON : Automatically searches for another station broadcasting the same
program in the same Radio Data System network with better reception
when the current reception is poor.;
OFF :Cancels.
TI ON :Allows the unit to temporarily switch to Traffic Information if available
(“TI” lights up).;
OFF :Cancels.
RADIO
Search for a station
1 Press repeatedly to select TUNER.
2 Press repeatedly (or press / on the remote
control) to select FM1/FM2/FM3/AM/SW1/SW2.
3 Press S/T(or press S/ on the remote control) to
search for a station.
• To change the searching method for S/T: Press
repeatedly.
AUTO1 : Automatically search for a station.
AUTO2 : Search for a preset station.
MANUAL : Manually search for a station.
• To store a station: Press and hold one of the number buttons (1to6).
• To select a stored station: Press one of the number buttons (1to6)
(or press one of the number buttons (1to6) on the remote control).
Direct Access Tuning (using the remote control)
1 Press DIRECT to enter Direct Access Tuning.
2 Press the number buttons to enter a frequency.
3 Press to search for a station.
• To cancel, press or DIRECT.
• If no operation is done for 10seconds after step2, Direct Access Tuning
is automatically canceled.
ENGLISH
JS_KWD_KDC_BT610U_MN_EN_4.indd 6JS_KWD_KDC_BT610U_MN_EN_4.indd 6 26-Aug-16 5:20:53 PM26-Aug-16 5:20:53 PM

ENGLISH 7
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
RADIO
PTY SEARCH 1 Turn the volume knob to select the available Program Type, then press
the knob.
2 Turn the volume knob to select the PTY language ( ENGLISH / FRENCH /
GERMAN ), then press the knob.
3 Press S / T to start searching.
CLOCK
TIME SYNC ON
:Synchronizes the unit’s time to the Radio Data System station time.;
OFF :Cancels.
Available Program Type for [PTY SEARCH]
SPEECH : NEWS , AFFAIRS , INFO (information), SPORT , EDUCATE , DRAMA ,
CULTURE , SCIENCE , VARIED , WEATHER , FINANCE , CHILDREN , SOCIAL ,
RELIGION , PHONE IN , TRAVEL , LEISURE , DOCUMENT
MUSIC
: POP M (music), ROCK M (music), EASY M (music), LIGHT M (music),
CLASSICS , OTHER M (music), JAZZ , COUNTRY , NATION M (music),
OLDIES , FOLK M (music)
The unit will search for the Program Type categorized under [SPEECH] or
[MUSIC] if selected.
•
[MONO SET] / [NEWS SET] / [REGIONAL] / [AF SET] / [TI] / [PTY SEARCH] is selectable
only when the band is FM1/FM2/FM3.
• If the volume is adjusted during reception of traffic information, alarm
or news bulletin, the adjusted volume is memorized automatically. It
will be applied the next time traffic information, alarm or news bulletin
is turned on.
AUX
Preparation:
Select
[ON] for [BUILT-IN AUX] for [SOURCE SELECT] . ( 5)
Start listening
1 Connect a portable audio player (commercially available).
2 Press repeatedly to select AUX.
3 Turn on the portable audio player and start playback.
Set the AUX name
While listening to a portable audio player connected to the unit...
1 Press the volume knob to enter [FUNCTION] .
2 Turn the volume knob to select [SYSTEM] , then press the knob.
3 Turn the volume knob to select [AUX NAME SET] , then press the knob.
4 Turn the volume knob to select an item, then press the knob.
AUX (default)/ DVD / PORTABLE / GAME / VIDEO / TV
5 Press and hold to exit.
To return to the previous setting item, press .
Auxiliary input jack
Portable audio
player
3.5mm stereo mini plug with “L” shaped connector
(commercially available)
JS_KWD_KDC_BT610U_MN_EN_4.indd 7JS_KWD_KDC_BT610U_MN_EN_4.indd 7 26-Aug-16 5:20:54 PM26-Aug-16 5:20:54 PM

8
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CD/USB/iPod/ANDROID
Start playback
The source changes automatically and
playback starts.
CD
*1
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
*2
Do not leave the cable inside the car when not using.
To On the faceplate On the remote control
Playback/pause Press . Press .
Reverse/Fast-forward*4Press and hold S/T. Press and hold S/ .
Select a track/file Press S/T. Press S/ .
Select a folder*5Press J/K.Press / .
Repeat play*6Press repeatedly.
TRACK REPEAT / ALL REPEAT : Audio CD
FILE REPEAT / FOLDER REPEAT / ALL REPEAT : MP3/WMA/AAC/WAV/FLAC file
FILE REPEAT / FOLDER REPEAT / REPEAT OFF : iPod or ANDROID
Random play*6Press repeatedly.
DISC RANDOM / RANDOM OFF : Audio CD
FOLDER RANDOM / RANDOM OFF : MP3/WMA/AAC/WAV/FLAC file, iPod or
ANDROID
Press and hold to select
ALL RANDOM .*7
*3
When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the instructions
to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device
before connecting. For more information, visit <www.kenwood.com/cs/ce/>.
*4
For ANDROID: Applicable only when [BROWSE MODE] is selected. ( 9)
*5
For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID.
*6
For iPod/ANDROID: Applicable only when [MODE OFF] / [BROWSE MODE] is selected. ( 9)
*7
For CD: Only for MP3/WMA/AAC files.
ENGLISH
Label side M Eject disc
USB input terminal
CA-U1EX (max.: 500mA)
(optional accessory)
Micro USB 2.0 cable
*2
(commercially available)
KCA-iP102/KCA-iP103 (optional
accessory)
*1
or accessory of the
iPod/iPhone
*2
USB
iPod/iPhone
ANDROID*3
JS_KWD_KDC_BT610U_MN_EN_4.indd 8JS_KWD_KDC_BT610U_MN_EN_4.indd 8 26-Aug-16 5:20:54 PM26-Aug-16 5:20:54 PM

ENGLISH 9
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CD/USB/iPod/ANDROID
Select control mode
While in iPodUSB source, press 5repeatedly.
MODE ON : Control iPod using the iPod itself. However, you can still play/
pause, file skip, fast-forward or reverse from this unit.
MODE OFF : Control iPod from this unit.
While in ANDROID source, press 5 repeatedly.
BROWSE MODE : Control Android device from this unit via KENWOOD
MUSIC PLAY application installed in the Android device.
HAND MODE : Control Android device using the Android device itself via
other media player applications installed in the Android
device. However, you can still play/pause and file skip from
this unit.
Select music drive
While in USB source, press 5repeatedly.
Stored songs in the following drive will be played back.
• Selected internal or external memory of a smartphone (Mass Storage
Class).
• Selected drive of a multiple drives device.
Listen to TuneIn Radio/TuneIn Radio Pro/Aupeo
While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the
iPod/iPhone to the USB input terminal of the unit.
• The unit will output the sound from these applications.
Select a file from a folder/list
For iPod/ANDROID, applicable only when [MODE OFF] / [BROWSE MODE] is
selected.
1 Press .
2 Turn the volume knob to select a folder/list, then press the knob.
3 Turn the volume knob to select a file, then press the knob.
Quick Search (applicable only for CD, USB and ANDROID source)
If you have many files, you can search through them quickly.
Turn the volume knob quickly to browse through the list quickly.
Skip Search (applicable only for iPod USB and ANDROID source)
Press S/Tto search at a preset skip search ratio. ( 10,
[SKIP SEARCH])
• Pressing and holding S/Tsearches at a 10 % ratio.
Alphabet search (applicable only for iPod USB and ANDROID source)
You can search for a file according to the first character.
For iPod USB source
1 Turn the volume knob quickly to enter character search.
2 Turn the volume knob to select the character.
• Select “
*” to search for a character other than AtoZ, 0to9.
3 Press S/Tto move to the entry position.
• You can enter up to 3characters.
4 Press the volume knob to start searching.
For ANDROID source
1 Press J/Kto enter character search.
2 Turn the volume knob to select the character.
^A^: Upper case letters (A to Z)
_A_: Lower case letters (a to z)
-0-: Numbers (0 to 9)
***: Character other than AtoZ, 0to9
3 Press the volume knob to start searching.
• To return to the root folder/first file/top menu, press 5.
(Not applicable for
BT AUDIO source.)
• To return to the previous setting item, press .
• To cancel, press and hold .
JS_KWD_KDC_BT610U_MN_EN_4.indd 9JS_KWD_KDC_BT610U_MN_EN_4.indd 9 26-Aug-16 5:20:55 PM26-Aug-16 5:20:55 PM

10
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CD/USB/iPod/ANDROID
Direct Music Search (using the remote control)
1 Press DIRECT.
2 Press the number buttons to enter a track/file number.
3 Press to search for music.
• To cancel, press or DIRECT.
• Not available if Random Play is selected.
• Not applicable for iPodUSB and ANDROID source.
Settings to use KENWOOD Remote application
KENWOOD Remote application is designed to control the KENWOOD car
receiver’s operations from the iPhone/iPod (via USB input terminal).
Preparation:
Install the latest version of KENWOOD Remote application on your device
before connecting. For more information, visit <www.kenwood.com/cs/ce/>.
You can make the settings in the same way as connection via Bluetooth. ( 17)
Other settings
1 Press the volume knob to enter
[FUNCTION] .
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
Default: XX
USB
MUSIC DRIVE DRIVE CHANGE
:The next drive ( [DRIVE 1] to [DRIVE 4] ) is selected
automatically and playback starts.
Repeat steps
1 to 3 to select the following drives.
SKIP SEARCH 0.5% / 1% / 5% / 10% : While listening to iPodUSB or ANDROID source, selects
the skip search ratio over the total files.
Pandora®
Preparation:
Install the latest version of the Pandora application on your device
(iPhone/iPod touch), then create an account and log in to Pandora.
• Select
[ON] for [PANDORA SRC] in [SOURCE SELECT] . ( 5)
Start listening
1 Open the Pandora application on your device.
2 Connect your device to the USB input terminal.
3 Press repeatedly to select PANDORA.
Broadcast starts automatically.
To On the faceplate On the remote control
Playback/pause Press . Press .
Skip a track Press T.Press .
Thumbs up or thumbs
down*3
Press J/K.Press /
.
*1
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
*2
Do not leave the cable inside the car when not using.
*3
If thumbs down is selected, the current track is skipped.
USB input terminal
KCA-iP102/KCA-iP103 (optional accessory)
*1
or accessory of the iPod/iPhone
*2
ENGLISH
JS_KWD_KDC_BT610U_MN_EN_4.indd 10JS_KWD_KDC_BT610U_MN_EN_4.indd 10 26-Aug-16 5:20:56 PM26-Aug-16 5:20:56 PM

ENGLISH 11
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Create and save a new station
1 Press .
2 Turn the volume knob to select [NEW STATION] , then press the knob.
3 Turn the volume knob to select [FROM ARTIST] or [FROM TRACK] , then press the knob.
A new station is created based on the artist or current song.
4 Press and hold one of the number buttons (1to5) to store.
To select a stored station: Press one of the number buttons (1to5).
Search for a registered station
1 Press .
2 Turn the volume knob to select an item, then press the knob.
[SORT BY DATE] : According to the registered date
[SORT BY A-Z] : By alphabetical order
3 Turn the volume knob (or press J/ Kon the remote control) to select the desired
station.
4 Press the volume knob (or press on the remote control) to confirm.
To cancel, press and hold .
Bookmark current song information
Press and hold the volume knob.
“BOOKMARKED” appears and the information is stored to your device.
• The bookmark is available on your Pandora account but not on this unit.
Delete a station
While listening to PANDORA...
1 Press .
2 Turn the volume knob to select [STATION DEL] , then press the knob.
3 Turn the volume knob to select [SORT BY DATE] or [SORT BY A-Z] , then press the knob.
4 Turn the volume knob to select the desired station to delete, then press the knob.
5 Turn the volume knob to select [YES] , then press the knob.
6 Press and hold to exit.
To return to the previous setting item, press .
Pandora® BLUETOOTH®
BLUETOOTH — Connection
Supported Bluetooth profiles
– Hands-Free Profile (HFP)
– Advanced Audio Distribution Profile (A2DP)
– Audio/Video Remote Control Profile (AVRCP)
– Serial Port Profile (SPP)
– Phonebook Access Profile (PBAP)
Supported Bluetooth codecs
– Sub Band Codec (SBC)
– Advanced Audio Coding (AAC)
Connect the microphone
Adjust the
microphone angle Secure using cord clamps
(not supplied) if necessary.
Microphone
(supplied)
Rear panel
Microphone
input jack
JS_KWD_KDC_BT610U_MN_EN_4.indd 11JS_KWD_KDC_BT610U_MN_EN_4.indd 11 26-Aug-16 5:20:57 PM26-Aug-16 5:20:57 PM

12
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ENGLISH
Pair and connect a Bluetooth device for the first time
1 Press to turn on the unit.
2 Search and select this unit model name (KDC-BT6**U/KDC-BT5**U)
on the Bluetooth device.
“PAIRING” “PASS XXXXXX” Device name “PRESS” “VOLUME
KNOB” appears on the display.
• For some Bluetooth devices, you may need to enter the Personal
Identification Number (PIN) code immediately after searching.
3 Press the volume knob to start pairing.
“PAIRING OK” appears when pairing is completed.
Once pairing is completed, Bluetooth connection is established
automatically.
• : “BT1” and/or “BT2” indicator on the faceplate lights up.
• : “BT1” and/or “BT2” on the display window lights up.
• This unit supports Secure Simple Pairing (SSP).
• Up to five devices can be registered (paired) in total.
• Once the pairing is completed, the Bluetooth device will remain
registered in the unit even if you reset the unit. To delete the paired
device,
16, [DEVICE DELETE] .
• A maximum of two Bluetooth phones and one Bluetooth audio device
can be connected at any time.
However, while in BT AUDIO source, you can connect to five Bluetooth
audio devices and switch between these five devices.
( 17)
• Some Bluetooth devices may not automatically connect to the unit
after pairing. Connect the device to the unit manually.
• Refer to the instruction manual of the Bluetooth device for more
information.
BLUETOOTH®
Auto Pairing
When you connect iPhone/iPod touch/Android device to the USB input
terminal, pairing request (via Bluetooth) is automatically activated.
Press the volume knob to pair once you have confirmed the device
name.
Automatic pairing request is activated only if:
– Bluetooth function of the connected device is turned on.
–
[AUTO PAIRING] is set to [ON] . ( 16)
– KENWOOD MUSIC PLAY application is installed on the Android device
(
8 ) and [BROWSE MODE] is selected. ( 9)
JS_KWD_KDC_BT610U_MN_EN_4.indd 12JS_KWD_KDC_BT610U_MN_EN_4.indd 12 26-Aug-16 5:20:57 PM26-Aug-16 5:20:57 PM

ENGLISH 13
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH — Mobile phone
Receive a call
When there is an incoming call:
•
: ZONE 2 illuminates in green color and
flashes.
• The unit answers the call automatically if
[AUTO ANSWER]
is set to a selected time.
( 14)
During a call:
•
: ZONE 1 illuminates according to
the settings made for
[DISPLAY] ( 22) and ZONE 2
illuminates in green color.
• If you turn off the unit or detach the faceplate, the
Bluetooth connection is disconnected.
The following operations may differ or not available
depending on the connected phone.
BLUETOOTH®
To On the faceplate On the remote control
First incoming call....
Answer a call Press or the volume knob
or one of the number buttons
(1to 6).
Press .
Reject a call Press .Press .
End a call Press .Press .
While talking on the first incoming call...
Answer another incoming
call and hold the current
call
Press . Press .
Reject another incoming
call
Press .Press .
While having two active calls...
End current call and
activate held call
Press .Press .
Swap between the
current call and held call
Press . Press .
Adjust the phone volume
[00] to [35] (Default: [15] )
Turn the volume knob during
a call.
• This adjustment will not
affect the volume of the other
sources.
( Not available )
Switch between hands-free
and private talk modes
Press during a call.
• Operations may vary
according to the connected
Bluetooth device.
( Not available )
JS_KWD_KDC_BT610U_MN_EN_4.indd 13JS_KWD_KDC_BT610U_MN_EN_4.indd 13 26-Aug-16 5:20:59 PM26-Aug-16 5:20:59 PM

14
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ENGLISH
BLUETOOTH®
Improve the voice quality
While talking on the phone...
1 Press the volume knob to enter [FUNCTION] .
2 Turn the volume knob to select an item (see the following table), then press
the knob.
3 Repeat step 2until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
Default: XX
MIC GAIN –10 to +10 ( –4 ):The sensitivity of the microphone increases as the number increased.
NR LEVEL –5 to +5 ( 0 ):Adjust the noise reduction level until the least noise is being heard during
a phone conversation.
ECHO CANCEL –5 to +5 ( 0 ):Adjust the echo cancellation delay time until the least echo is being heard
during a phone conversation.
Make the settings for receiving a call
1 Press to enter Bluetooth mode.
2 Turn the volume knob to select an item (see the following table), then press
the knob.
3 Repeat step 2until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
XX
SETTINGS
AUTO ANSWER 1
to 30 :The unit answers incoming call automatically in the selected time (in seconds).;
OFF :Cancels.
BATT/SIGNAL
*
(For )
AUTO :Shows the strength of the battery and signal when the unit detects a Bluetooth
device and the Bluetooth device is connected.;
OFF :Cancels. Clock time is shown.
* Functionality depends on the type of the phone used.
Make a call
You can make a call from the call history, phonebook, or
dialing the number. Call by voice is also possible if your
mobile phone has the feature.
1 Press to enter Bluetooth mode.
“(First device name)” appears.
• If two Bluetooth phones are connected, press again
to switch to another phone.
“(Second device name)” appears.
2 Turn the volume knob to select an item (see the
following table), then press the knob.
3 Repeat step 2until the desired item is selected/
activated or follow the instructions stated on the
selected item.
4 Press and hold to exit.
To return to the previous setting item, press .
CALL HISTORY (Applicable only if the phone supports PBAP.)
1 Press the volume knob to select a name or a phone
number.
• : “INCOMING”, “OUTGOING”, or
“MISSED” is shown on the lower part of the display to
indicate the previous call status.
: “I” indicates call received, “O”
indicates call made, “M” indicates call missed.
• Press
DISP to change the display category
(NUMBER or NAME).
• “NO DATA” appears if there is no recorded call
history.
2 Press the volume knob to call.
JS_KWD_KDC_BT610U_MN_EN_4.indd 14JS_KWD_KDC_BT610U_MN_EN_4.indd 14 26-Aug-16 5:21:01 PM26-Aug-16 5:21:01 PM

ENGLISH 15
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
PHONE BOOK (Applicable only if the phone supports PBAP.)
1 Turn the volume knob quickly to enter alphabet search mode (if the
phonebook contains many contacts).
The first menu (ABCDEFGHIJK) appears.
• To go to the other menu (LMNOPQRSTUV or WXYZ1
* ), press J/ K .
• To select the desired first letter, turn the volume knob or press
S/T ,
then press the knob.
Select “1” to search with numbers and select “
* ” to search with symbols.
2 Turn the volume knob to select a name, then press the knob.
3 Turn the volume knob to select a phone number, then press the knob to call.
• The phonebook of the connected phone is automatically transferred to the unit
when pairing.
• Contacts are categorized as: HOME, OFFICE, MOBILE, OTHER, GENERAL or HM
(home), OF (office), MO (mobile), OT (other), GE (general)
• This unit can display only non-accent letters. (Accent letters such as “Ú” is
shown as “U”.)
NUMBER DIAL 1 Turn the volume knob to select a number (0 to 9) or character ( , #, +).
2 Press S/T to move the entry position.
Repeat steps
1 and 2 until you finish entering the phone number.
3 Press the volume knob to call.
(or using the remote control)
1 Press the number buttons ( 0 to 9 ) to enter the phone number.
2 Press to call.
VOICE Speak the name of the contact you want to call or the voice command to control
the phone functions.
( Make a call using voice recognition)
BATT LOW
/ MID / FULL
*
:Shows the strength of the battery.
NO SIGNAL / LOW / MID / MAX
*
:Shows the strength of the current received signal.
* Functionality depends on the type of the phone used.
Make a call using voice recognition
1 Press and hold to activate the voice recognition of the
connected phone.
2 Speak the name of the contact you want to call or the voice
command to control the phone functions.
• Supported Voice Recognition features vary for each phone.
Refer to the instruction manual of the connected phone for
details.
• This unit also supports the intelligent personal assistant
function of iPhone.
Settings in memory
Store a contact in memory
You can store up to 6 contacts into the number buttons
(1to 6).
1 Press to enter Bluetooth mode.
2 Turn the volume knob to select [CALL HISTORY] , [PHONE BOOK] ,
or
[NUMBER DIAL] , then press the knob.
3 Turn the volume knob to select a contact or enter a phone
number.
If a contact is selected, press the volume knob to show the
phone number.
4 Press and hold one of the number buttons (1to 6).
“STORED” appears when the contact is stored.
To erase a contact from the preset memory, select
[NUMBER DIAL]
in step 2and store a blank number.
Make a call from memory
1 Press to enter Bluetooth mode.
2 Press one of the number buttons (1to 6).
3 Press the volume knob to call.
“NO MEMORY” appears if there is no contacts stored.
JS_KWD_KDC_BT610U_MN_EN_4.indd 15JS_KWD_KDC_BT610U_MN_EN_4.indd 15 26-Aug-16 5:21:02 PM26-Aug-16 5:21:02 PM

16
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ENGLISH
BLUETOOTH®
Other settings
1 Press the volume knob to enter
[FUNCTION] .
2 Turn the volume knob to select an item (see the following table), then
press the knob.
3 Repeat step 2until the desired item is selected/activated or follow the
instructions stated on the selected item.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
XX
BT MODE
PHONE SELECT
Selects the phone or audio device to connect or disconnect.
“
*
” appears in front of the device name when connected.
““ appears in front of the current playback audio device.
• You can only connect a maximum of two Bluetooth phones and one Bluetooth
audio device at any time.
AUDIO SELECT
DEVICE DELETE
1 Turn the volume knob to select a device to delete, then press the knob.
2 Turn the volume knob to select [YES] or [NO] , then press the knob.
PIN CODE EDIT
(0000)
Changes the PIN code (up to 6 digits).
1 Turn the volume knob to select a number.
2 Press S / T to move the entry position.
Repeat steps
1 and 2 until you finish entering the PIN code.
3 Press the volume knob to confirm.
RECONNECT ON :The unit automatically reconnect when the last connected Bluetooth device is
within range.;
OFF :Cancels.
AUTO PAIRING ON :The unit automatically pair supported Bluetooth device (iPhone/iPod touch/
Android device) when it is connected through USB input terminal.Depending
on the operating system of the connected device, this function may not work. ;
OFF :Cancels.
INITIALIZE YES :Initializes all the Bluetooth settings (including stored pairing, phonebook,
and etc.).;
NO :Cancels.
Bluetooth test mode
You can check the connectivity of the supported profile between
the Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
1 Press and hold .
“PLEASE PAIR YOUR PHONE PIN 0000” appears.
2 Search and select this unit model name (KDC-BT6**U/
KDC-BT5**U) on the Bluetooth device.
3 Operate the Bluetooth device to confirm pairing.
“TESTING” flashes on the display.
The connectivity result (OK or NG) appears after the test.
PAIRING: Pairing status
HF CNT: Hands-Free Profile (HFP) compatibility
AUD CNT: Advanced Audio Distribution Profile (A2DP)
compatibility
PB DL: Phonebook Access profile (PBAP) compatibility
To cancel test mode, press and hold to turn off the unit.
JS_KWD_KDC_BT610U_MN_EN_4.indd 16JS_KWD_KDC_BT610U_MN_EN_4.indd 16 26-Aug-16 5:21:02 PM26-Aug-16 5:21:02 PM

ENGLISH 17
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
Audio player via Bluetooth
1 Press repeatedly (or press SRC on the remote control) to select BTAUDIO.
2 Operate the Bluetooth audio player to start playback.
To On the faceplate On the remote control
Playback/pause Press . Press .
Select group or folder Press J/ K.Press / .
Reverse/Forward skip Press S/T. Press S/ .
Reverse/Fast-forward Press and hold S/T.Press and hold
S/ .
Repeat play Press repeatedly.
ALL REPEAT , FILE REPEAT , REPEAT OFF
( Not available )
Random play Press and hold to select
ALL RANDOM .
• Press to select
RANDOM OFF .
( Not available )
Select a file from a
folder/list
Refer to “Select a file from a
folder/list” on page 9. ( Not available )
Switch between
connected Bluetooth
audio devices
Press 5.*
( Not available )
*
Pressing the “Play” key on the connected device itself also causes switching of sound output from the device.
Operations and display indications may differ according to their availability on the
connected device.
Settings to use KENWOOD Remote application
KENWOOD Remote application is designed to control the
KENWOOD car receiver’s operations from the iPhone/
iPod (via Bluetooth or via USB input terminal) or Android
smartphone (via Bluetooth).
Preparation: Install the latest version of KENWOOD Remote application on
your device before connecting. For more information, visit
<www.kenwood.com/cs/ce/>.
1 Press the volume knob to enter [FUNCTION] .
2 Turn the volume knob to select an item (see the
following table), then press the knob.
3 Repeat step 2until the desired item is selected or
activated.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
XX
REMOTE APP
SELECT
Select the device (IOS or ANDROID) to use the application.
IOS YES : Selects iPhone/iPod to use the application via Bluetooth
or connected via USB input terminal.;
NO : Cancels.
If IOS is selected, select iPod BT source (or iPod USB if
your iPhone/iPod is connected via USB input terminal) to
activate the application.
• The connectivity of the application will be interrupted or
disconnected if:
– You change from iPod BT source to any playback
source connected via the USB input terminal.
– You change from iPod USB source to iPod BT source.
ANDROID YES :Selects Android smartphone to use the application via
Bluetooth.;
NO : Cancels.
ANDROID LIST *:Selects the Android smartphone to use from the list.
BLUETOOTH — Audio
While in BT AUDIO source,
you can connect to five
Bluetooth audio devices
and switch between these
five devices.
JS_KWD_KDC_BT610U_MN_EN_4.indd 17JS_KWD_KDC_BT610U_MN_EN_4.indd 17 26-Aug-16 5:21:03 PM26-Aug-16 5:21:03 PM

18
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
While listening to any source...
1 Press the volume knob to enter [FUNCTION] .
2 Turn the volume knob to select an item (see the following
table), then press the knob.
3 Repeat step 2until the desired item is selected or activated.
4 Press and hold to exit.
(or using the remote control)
1 Press AUD to enter [AUDIO CONTROL] .
2 Press J/ Kto select an item, then press .
To return to the previous setting item, press .
Default: XX
AUDIO CONTROL
SUB-W LEVEL LEVEL –50
to LEVEL +10 ( LEVEL 0 ): Adjusts the subwoofer
output level.
MANUAL EQ The sound elements (frequency level, tone level, Q factor) are
preset into each selection (
BAND1 LEVEL to BAND13 LEVEL ).
BAND1 LEVEL
LEVEL LEVEL–9
to LEVEL +9 ( LEVEL 0 ):Adjusts the level to
memorize for each source. (Before making an adjustment, select
the source you want to adjust.)
BASS EXTEND ON :Turns on the extended bass.; OFF :Cancels.
BAND2 LEVEL to
BAND13 LEVEL
LEVEL–9 to LEVEL +9 ( LEVEL 0 ):Adjusts the level to
memorize for each source. (Before making an adjustment, select
the source you want to adjust.)
Q FACTOR 1.35 / 1.50 / 2.00 :Adjust the quality factor.
PRESET EQ NATURAL / ROCK / POPS / EASY / TOP40 / JAZZ / POWERFUL /
USER : Selects a preset equalizer suitable to the music genre.
(Select
[USER] to use the settings made in [MANUAL EQ] .)
ENGLISH
BLUETOOTH®
STATUS Shows the status of the selected device.
IOS CONNECTED : You are able to use the application using the iPhone/iPod connected
via Bluetooth or USB input terminal.
IOS NOT CONNECTED : No IOS device is connected to use the application.
ANDROID CONNECTED : You are able to use the application using the Android
smartphone connected via Bluetooth.
ANDROID NOT CONNECTED : No Android device is connected to use the application.
* Displayed only when [ANDROID] of [SELECT] is set to [YES] .
Listen to iPhone/iPod via Bluetooth
You can listen to the songs on the iPhone/iPod via Bluetooth on this unit.
Press repeatedly to select iPodBT.
• You can operate the iPod/iPhone in the same way as iPod/iPhone via USB
input terminal.
( 8)
• If you plug in an iPhone/iPod to the USB input terminal while listening to
iPodBT source, the source automatically change to iPodUSB. Press to
select iPodBT if the device is still connected via Bluetooth.
Internet radio via Bluetooth
Listen to Pandora
You can listen to Pandora on the iPhone/iPod/Android device via Bluetooth on
this unit.
• Make sure the USB input terminal is not connected to any device.
Preparation:
Select
[ON] for [PANDORA SRC] in [SOURCE SELECT] . ( 5)
1 Open the Pandora application on your device.
2 Connect your device via Bluetooth connection. ( 12)
3 Press repeatedly to select PANDORA (for iPhone/iPod) or
PANDORA BT (for Android device).
The source switches and broadcast starts automatically.
• You can operate Pandora in the same way as Pandora via USB input terminal.
( 10)
JS_KWD_KDC_BT610U_MN_EN_4.indd 18JS_KWD_KDC_BT610U_MN_EN_4.indd 18 26-Aug-16 5:21:04 PM26-Aug-16 5:21:04 PM

ENGLISH 19
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BASS BOOST LEVEL1 / LEVEL2 / LEVEL3 / LEVEL4 / LEVEL5 or LV1 / LV2 / LV3 / LV4 /
LV5 :Selects your preferred bass boost level.; OFF :Cancels.
LOUDNESS LEVEL1 / LEVEL2 or LV1 / LV2 :Selects your preferred low and high
frequencies boost to produce a well-balanced sound at a low volume
level.;
OFF :Cancels.
SUBWOOFER SET ON :Turns on the subwoofer output.; OFF :Cancels.
FADER (Not applicable if 3-way crossover is selected.)
R15 to F15 ( 0 ):Adjusts the rear and front speaker output balance.
BALANCE L15 to R15 ( 0 ):Adjusts the left and right speaker output balance.
VOLUME OFFSET –15 to +6 ( 0 ):Preset the initial volume level of each source. (Before
adjustment, select the source you want to adjust.)
SOUND EFFECT
SOUND RECNSTR
(Sound
reconstruction)
(Not applicable for TUNER source and AUX source.)
ON :Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost
in audio data compression.;
OFF :Cancels.
SPACE ENHANCE (Not applicable for TUNER source.)
SMALL / MEDIUM / LARGE or SML / MED / LRG :Virtually enhances the
sound space.;
OFF :Cancels.
SND REALIZER LEVEL1 / LEVEL2 / LEVEL3 or LV1 / LV2 / LV3 :Virtually makes the sound
more realistic.;
OFF :Cancels.
STAGE EQ LOW / MIDDLE / HIGH or LOW / MID / HI :Virtually adjust the sound
position heard from the speakers.;
OFF :Cancels.
DRIVE EQ ON : Boosts the frequency to reduce the noise heard from outside the
car or running noise of the tyres.;
OFF :Cancels.
SPEAKER SIZE Depending on the crossover type you have selected ( 5) , 2-way
crossover or 3-way crossover setting items will be shown
( 19, 20) .
By default, 2-way crossover type is selected.
X’OVER
DTA SETTINGS
For settings, 21, Digital Time Alignment Settings.
CAR SETTINGS
• : For 2-way crossover: [SUB-W LEVEL] / [SUBWOOFER SET] is selectable
only if
[SWITCH PREOUT] is set to [SUB-W] . ( 4)
• [SUB-W LEVEL] is selectable only if [SUBWOOFER SET] is set to [ON] .
Crossover settings
Below are the available setting items for 2-way crossover and 3-way
crossover.
SPEAKER SIZE
Selects according to the connected speaker size for optimum
performance.
• The frequency and slope settings are automatically set for the crossover
of the selected speaker.
• When 2-way crossover is selected, if [NONE] is selected for [TWEETER] of
[FRONT] , [REAR] and [SUBWOOFER] for [SPEAKER SIZE] , the [X ‘ OVER] setting of
the speaker is not available.
• When 3-way crossover is selected, if
[NONE] is selected for [WOOFER] of
[SPEAKER SIZE] , the [X’OVER] setting of [WOOFER] is not available.
X ‘ OVER
• [FRQ]
/ [F - HPF FRQ] / [R - HPF FRQ] / [SW LPF FRQ] / [HPF FRQ] / [LPF FRQ] : Adjusts the
crossover frequency for the selected speakers (high pass filter or low
pass filter).
If
[THROUGH] is selected, all signals are sent to the selected speakers.
• [F - HPF SLOPE] / [R - HPF SLOPE] / [SW LPF SLOPE] / [HPF SLOPE] / [LPF SLOPE] / [SLOPE]:
Adjusts the crossover slope.
Selectable only if a setting other than [THROUGH] is selected for the
crossover frequency.
• [SW LPF PHASE] / [PHASE]: Selects the phase of the speaker output to be in
line with the other speaker output.
• [GAIN LEFT] / [GAIN RIGHT] / [F - HPF GAIN] / [R - HPF GAIN] / [SW LPF GAIN] / [GAIN] :
Adjusts the output volume of the selected speaker.
AUDIO SETTINGS
JS_KWD_KDC_BT610U_MN_EN_4.indd 19JS_KWD_KDC_BT610U_MN_EN_4.indd 19 26-Aug-16 5:21:05 PM26-Aug-16 5:21:05 PM

20
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
2-way crossover setting items
SPEAKER SIZE
FRONT SIZE 8CM
/ 10CM / 12CM / 13CM / 16CM / 17CM / 18CM / 4×6 /
5×7 / 6×8 / 6×9 / 7×10
TWEETER SMALL
/ MIDDLE / LARGE / NONE (not connected)
REAR 8CM / 10CM / 12CM / 13CM / 16CM / 17CM / 18CM / 4×6 / 5×7 / 6×8 / 6×9 / 7×10/
NONE
(not connected)
SUBWOOFER
*1
16CM / 20CM / 25CM / 30CM / 38CM OVER / NONE (not connected)
X ' OVER
TWEETER FRQ 1KHZ
/ 1.6KHZ / 2.5KHZ / 4KHZ / 5KHZ / 6.3KHZ / 8KHZ /
10KHZ / 12.5KHZ
GAIN LEFT –8
to 0
GAIN RIGHT –8
to 0
FRONT HPF F - HPF FRQ 30HZ
/ 40HZ / 50HZ / 60HZ / 70HZ / 80HZ / 90HZ / 100HZ /
120HZ / 150HZ / 180HZ / 220HZ / 250HZ/THROUGH
F - HPF SLOPE –6DB
/ –12DB / –18DB / –24DB
F - HPF GAIN –8
to 0
REAR HPF R - HPF FRQ
(Refer FRONT HPF settings above.) R - HPF SLOPE
R - HPF GAIN
SUBWOOFER
LPF
*1
SW LPF FRQ 30HZ / 40HZ / 50HZ / 60HZ / 70HZ / 80HZ / 90HZ / 100HZ /
120HZ / 150HZ / 180HZ / 220HZ / 250HZ / THROUGH
SW LPF SLOPE –6DB
/ –12DB / –18DB / –24DB
SW LPF PHASE REVERSE
(180°)/ NORMAL (0°)
SW LPF GAIN –8 to 0
*1
Selectable only when [SWITCH PREOUT] is set to [SUB-W] ( 4) (for ),
and [SUBWOOFER SET] is set to [ON] . ( 19)
3-way crossover setting items
SPEAKER SIZE
TWEETER SMALL
/ MIDDLE / LARGE
MID RANGE
8CM/10CM/12CM/13CM/16CM/17CM/18CM/4×6/5×7/6×8/6×9
WOOFER
*2
16CM / 20CM / 25CM / 30CM / 38CM OVER / NONE (not connected)
X ' OVER
TWEETER HPF FRQ 1KHZ
/ 1.6KHZ / 2.5KHZ / 4KHZ / 5KHZ / 6.3KHZ /
8KHZ / 10KHZ / 12.5KHZ
SLOPE –6DB
/ –12DB
PHASE REVERSE
(180°)/ NORMAL (0°)
GAIN –8 to 0
MID RANGE HPF FRQ 30HZ
/ 40HZ / 50HZ / 60HZ / 70HZ / 80HZ / 90HZ /
100HZ / 120HZ / 150HZ / 180HZ / 220HZ / 250HZ /
THROUGH
HPF SLOPE –6DB
/ –12DB
LPF FRQ 1KHZ
/ 1.6KHZ / 2.5KHZ / 4KHZ / 5KHZ / 6.3KHZ /
8KHZ / 10KHZ / 12.5KHZ / THROUGH
LPF SLOPE –6DB
/ –12DB
PHASE REVERSE
(180°)/ NORMAL (0°)
GAIN –8 to 0
WOOFER
*2
LPF FRQ 30HZ / 40HZ / 50HZ / 60HZ / 70HZ / 80HZ / 90HZ /
100HZ / 120HZ / 150HZ / 180HZ / 220HZ / 250HZ /
THROUGH
SLOPE –6DB
/ –12DB
PHASE REVERSE
(180°)/ NORMAL (0°)
GAIN –8 to 0
*2
Selectable only when [SUBWOOFER SET] is set to [ON] . ( 19)
ENGLISH
JS_KWD_KDC_BT610U_MN_EN_4.indd 20JS_KWD_KDC_BT610U_MN_EN_4.indd 20 26-Aug-16 5:21:06 PM26-Aug-16 5:21:06 PM