Kenwood KDC-X7100DAB User manual

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
KDC-X7100DAB
CD-RECEIVER
INSTRUCTION MANUAL
B5A-1372-00 (XN)© 2016 JVC KENWOOD Corporation
JS_KWD_KDC_X7100DAB_XN_C_3.indd 1JS_KWD_KDC_X7100DAB_XN_C_3.indd 1 12/14/2016 9:17:27 AM12/14/2016 9:17:27 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
2
BEFORE USE
IMPORTANT
• To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe
Warning and Caution in this manual.
• Please keep the manual in a safe and accessible place for future reference.
WARNING
• Do not operate any function that takes your attention away from safe driving.
• Do not ingest the battery, Chemical Burn Hazard
The remote control supplied with this product contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Caution
Volume setting:
•
Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
•
Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
• USB rating for the USB cable from the rear of the unit is indicated on a label. ( 35)
• Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected
( 35) . Turn off the unit or change the source to STANDBY when parking at a low ceiling area.
Remote control (RC-406):
•
Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
How to read this manual
• Operations are explained mainly using buttons on the faceplate.
• English indications are used for the purpose of explanation. You can select the display language from the [FUNCTION] menu. ( 5)
• [XX] indicates the selected items.
• ( XX) indicates references are available on the stated page.
CONTENTS
BEFORE USE 2
BASICS 3
GETTING STARTED 4
1 Select the display language
and cancel the demonstration
2 Set the clock and date
3 Set the initial settings
DIGITAL RADIO 6
ANALOG RADIO 8
CD/USB/iPod/ANDROID 10
AUX 12
Pandora® 13
BLUETOOTH® 14
AUDIO SETTINGS 22
DISPLAY SETTINGS 25
REFERENCES 26
Maintenance
More information
TROUBLESHOOTING 29
SPECIFICATIONS 31
INSTALLATION/
CONNECTION 33
ENGLISH
JS_KWD_KDC_X7100DAB_XN_EN_3.indd 2JS_KWD_KDC_X7100DAB_XN_EN_3.indd 2 12/14/2016 9:18:24 AM12/14/2016 9:18:24 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
3
BASICS
To On the faceplate On the remote control
Turn on the power Press .
• Press and hold to turn off the power.
Press and hold SRC to turn off the power.
( Pressing SRC does not turn on the power. )
Adjust the volume Turn the volume knob. Press or .
• Press and hold to continuously increase the
volume to 15.
Press ATT during playback to attenuate the sound.
• Press again to cancel.
Select a source Press repeatedly. Press SRC repeatedly.
Change the display information Press DISP repeatedly.
( 28) ( Not available )
Faceplate
How to resetAttach Detach
Remote control (RC-406)
ENGLISH
Display
window
Pull out the insulation
sheet when using for the
first time.
How to replace the battery
Remote sensor (Do not expose to
bright sunlight.)
Volume
knob
Detach
button
Flashes when the unit
enters searching status.
Lights up when Bluetooth
connection is established.
( 14)
USB 1 cable from
the rear of the unit.
Auxiliary cable from
the rear of the unit.
USB 2 cable from
the rear of the unit.
JS_KWD_KDC_X7100DAB_XN_EN_3.indd 3JS_KWD_KDC_X7100DAB_XN_EN_3.indd 3 12/14/2016 9:18:25 AM12/14/2016 9:18:25 AM

4
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
Select the display language and cancel the demonstration
When you turn on the power for the first time (or [FACTORY RESET] is
set to
[YES] , 5 ), the display shows: “SEL LANGUAGE” “PRESS”
“VOLUMEKNOB”
1 Turn the volume knob to select [ENG] (English) or [SPA] (Spanish),
then press the knob.
[ENG] is selected for the initial setup.
Then, the display shows: “CANCEL DEMO” “PRESS” “VOLUME
KNOB”.
2 Press the volume knob.
[YES] is selected for the initial setup.
3 Press the volume knob again.
“DEMO OFF” appears.
Then, the display shows the selected crossover type: “2-WAY X ’OVER” or
“3-WAY X ’ OVER”
• To change the crossover type, see “Change the crossover type”.
( 5)
1
Set the clock and date
1 Press the volume knob to enter
[FUNCTION] .
2 Turn the volume knob to select [CLOCK] , then press the knob.
To adjust the clock
3 Turn the volume knob to select [CLOCK ADJUST] , then press the knob.
4 Turn the volume knob to make the settings, then press the knob.
Hour Minute
5 Turn the volume knob to select [CLOCK FORMAT] , then press the knob.
6 Turn the volume knob to select [12H] or [24H] , then press the knob.
To set the date
7 Turn the volume knob to select [DATE FORMAT] , then press the knob.
8 Turn the volume knob to select [DD/MM/YY] or [MM/DD/YY] , then press
the knob.
9 Turn the volume knob to select [DATE SET] , then press the knob.
10 Turn the volume knob to make the settings, then press the knob.
Day Month Year or Month Day Year
11 Press and hold to exit.
To return to the previous setting item, press .
Set the initial settings
1 Press repeatedly to enter STANDBY.
2 Press the volume knob to enter [FUNCTION] .
3 Turn the volume knob to select an item ( 5) , then press the knob.
4 Repeat step 3until the desired item is selected or activated.
5 Press and hold to exit.
To return to the previous setting item, press .
3
2
ENGLISH
JS_KWD_KDC_X7100DAB_XN_EN_3.indd 4JS_KWD_KDC_X7100DAB_XN_EN_3.indd 4 12/14/2016 9:18:25 AM12/14/2016 9:18:25 AM

ENGLISH 5
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
Default: XX
DISPLAY
EASY MENU
When entering [FUNCTION] ...
ON :ZONE 1 illumination changes to white color.;
OFF :ZONE 1 illumination remains as [COLOR SELECT] color. ( 26)
• ZONE 2 illumination changes to white color when you enter [FUNCTION] ,
irregardless of the
[EASY MENU] setting.
• Refer to the illustration on page 25 for ZONE identification.
TUNER SETTING
DAB L-BAND
*1
ON : Receives L-BAND ensemble during digital audio reception. ; OFF : Cancels.
DAB ANT
POWER
ON : Supplies power to the DAB antenna. Selects when using the supplied
antenna. ;
OFF : Does not supply power. Selects when using passive antenna
without booster.
( 36)
PRESET TYPE NORMAL
:Memorizes one station for each preset button in each band (FM1/FM2/
FM3/AM/SW1/SW2/DB1/DB2/DB3).;
MIX :Memorizes one station (digital radio or
analog radio) for each preset button, regardless of the selected band.
SYSTEM
KEY BEEP
*2
ON :Activates the keypress tone.; OFF :Deactivates.
TDF ALARM
*2
ON : Activates the alarm if you forget to detach the faceplate when ACC is set to
OFF. ;
OFF : Deactivates.
SOURCE SELECT
PANDORA SRC ON
:Enables PANDORA in source selection.; OFF :Disables. ( 13)
BUILT-IN AUX ON
:Enables AUX in source selection.; OFF :Disables. ( 12)
CD READ 1
:Automatically distinguishes between audio file disc and music CD.;
2 :Forces to play as a music CD. No sound can be heard if an audio file disc is
played.
*1
This feature is not supported when using the supplied DAB antenna (without L-band support).
To use this feature, separately purchase a DAB antenna (with L-band support).
*2
Not applicable if 3-way crossover is selected.
F/W UPDATE
UPDATE SYSTEM/UPDATE DAB1/UPDATE DAB2
F/W UPDATE xxxx/
F/W UPDATE xxxxx/
F/W UPDATE Vxxx
YES :Starts upgrading the firmware.; NO :Cancels
(upgrading is not activated). For details on how to update
the firmware, visit <www.kenwood.com/cs/ce/>.
FACTORY RESET YES :Resets the settings to default (except the stored
station).;
NO :Cancels.
CLOCK
CLOCK DISPLAY ON
:The clock time is shown on the display even when
the unit is turned off.;
OFF :Cancels.
ENGLISH
Select the display language for [FUNCTION] menu and
music information if applicable.
By default,
[ENGLISH] is selected.
ESPANOL
Change the crossover type
1 Press repeatedly to enter STANDBY.
2 Press and hold number buttons 4and 5to enter crossover
select.
The current crossover type appears.
3 Turn the volume knob to select “2WAY” or “3WAY”, then
press the knob.
4 Turn the volume knob to select “YES” or “NO”, then press the
knob.
The selected crossover type appears.
• To cancel, press and hold .
• To adjust the selected crossover settings,
( 23, 24) .
Caution
Select a crossover type according to how the speakers are connected
( 35) . If you select a wrong type:
• The speakers may damage.
• The output sound level may be extremely high or low.
JS_KWD_KDC_X7100DAB_XN_EN_3.indd 5JS_KWD_KDC_X7100DAB_XN_EN_3.indd 5 12/14/2016 9:18:26 AM12/14/2016 9:18:26 AM

6
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
DIGITAL RADIO
About DAB (Digital Audio Broadcasting)
DAB is one of the digital radio broadcasting systems
available today. It can deliver digital quality sound
without any annoying interference or signal distortion.
Furthermore, it can carry text, pictures and data.
In contrast to FM broadcast, where each program
is transmitted on its own frequency, DAB combines
several programs (called “services”) to form one
“ensemble.”
The “primary component” (main radio station) is
sometimes accompanied by a “secondary component”
which can contain extra programs or other information.
Preparation:
1 Connect the supplied DAB antenna to the DAB
antenna jack.
( 35)
2 Press repeatedly to select DIGITAL AUDIO.
3 Press and hold (LISTUPDATE) to start the
Service List update.
“LIST UPDATE” appears and update starts.
“UPDATED” appears when update completes.
Updates take up to3 minutes. No interruption (such
as traffic information) is possible during updates.
• To cancel the Service List update:
Press and hold (LISTUPDATE) again.
Search for an ensemble
1 Press repeatedly to select DIGITAL AUDIO.
2 Press repeatedly (or press on the remote control) to select DB1/DB2/
DB3.
3 Press and hold S/T(or press and hold S/ on the remote control) to
search for an ensemble.
4 Press S/T(or press S/ on the remote control) to select an ensemble,
service or component to listen.
• To change the searching method for S/T: Press repeatedly.
AUTO1 : Press S/T: Select an ensemble, service or component.
Press and hold S/T: Automatically search for an ensemble.
AUTO2 : Press S/T: Search for a preset station.
MANUAL : Press S/T: Select an ensemble, service or component.
Press and hold S/T: Manually search for an ensemble.
• To store a service: Press and hold one of the number buttons (1to6).
• To select a stored service: Press one of the number buttons (1to6) (or press one of the
number buttons (1to 6) on the remote control).
Select a service
1 Press to enter Service Search mode.
2 Turn the volume knob or press J/Kto select a service, then press the knob.
(or using the remote control)
Press J/ Kto search for a service, then press .
To cancel the Service Search mode, press again.
ENGLISH
JS_KWD_KDC_X7100DAB_XN_EN_3.indd 6JS_KWD_KDC_X7100DAB_XN_EN_3.indd 6 12/14/2016 9:18:26 AM12/14/2016 9:18:26 AM

ENGLISH 7
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Select a service by name
1 Press to enter Service Search mode.
2 Turn the volume knob quickly to enter Alphabet Search mode.
3 Turn the volume knob or press S/Tto select the character to
be searched for.
Press J/Kto go to the previous/next page.
4 Press the volume knob to start searching.
5 Turn the volume knob to select a service, then press the knob.
To cancel the Alphabet Search mode, press again.
Other settings
1 Press the volume knob to enter
[FUNCTION] .
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
XX
TUNER SETTING
AF SET ON
:
While listening to DAB: Automatically switch to FM broadcasting the same
program if the DAB signal becomes weak. It will switch back to DAB sound
when the signal becomes strong again.
While listening to FM: Automatically switch to DIGITAL AUDIO source
broadcasting the same program (if available).;
OFF :Cancels.
TI ON :Allows the unit to temporarily switch to Traffic Information if available
(“TI” lights up).;
OFF :Cancels.
PTY SEARCH 1 Turn the volume knob to select the available Program Type ( 8) ,
then press the knob.
2 Turn the volume knob to select the PTY language ( ENGLISH / FRENCH /
GERMAN ), then press the knob.
3 Press S/T to start searching.
ASW SELECT TRAVEL , WARNINGS , NEWS , WEATHER , EVENT , SPECIAL , RAD INFO ,
SPORTS , FINANCE : Turn the volume knob to make a selection, then press
the knob.
“
*
” appears in front of the activated announcement type.
Automatically switch from any source to Digital radio ensembles
broadcasting an activated announcement type.
• Multiple announcement can be activated simultaneously.
• To deactivate, press the volume knob again (“
*
” goes off).
LIST UPDATE AUTO :Automatically update the DAB Service List when the power is
turned on.;
MANUAL :Updates the DAB Service List by pressing and
holding
(LIST UPDATE) .
PTY WATCH 1 Turn the volume knob to select the available Program Type, then press
.
The unit automatically switch from any source to Digital Radio
ensembles broadcasting the selected type of program.
Program Type : NEWS , AFFAIRS , INFO , SPORT , EDUCATE , DRAMA ,
CULTURE , SCIENCE , VARIED , POP  M (music), ROCK  M (music),
EASY  M (music), LIGHT  M (music), CLASSICS , OTHER  M (music),
WEATHER , FINANCE , CHILDREN , SOCIAL , RELIGION , PHONE IN ,
TRAVEL , LEISURE , JAZZ , COUNTRY , NATION  M (music), OLDIES ,
FOLK  M (music), DOCUMENT
OFF :Cancels.
2
Press the volume knob to enter PTY language selection.
3 Turn the volume knob to select the PTY language ( ENGLISH / FRENCH /
GERMAN ), then press the knob.
RELATED
SERVICE
ON :Enable Soft-Link function to switch to an alternative service which is
different audio program from the current audio program.;
OFF :Disable.
DIGITAL RADIO
JS_KWD_KDC_X7100DAB_XN_EN_3.indd 7JS_KWD_KDC_X7100DAB_XN_EN_3.indd 7 12/14/2016 9:18:26 AM12/14/2016 9:18:26 AM

8
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ANALOG RADIO
Search for a station
1 Press repeatedly to select TUNER.
2 Press repeatedly (or press / on the remote control)
to select FM1/FM2/FM3/AM/SW1/SW2.
3 Press S/T(or press S/ on the remote control) to search for
a station.
• To change the searching method for S/T: Press repeatedly.
AUTO1 : Automatically search for a station.
AUTO2 : Search for a preset station.
MANUAL : Manually search for a station.
• To store a station: Press and hold one of the number buttons (1to6).
• To select a stored station: Press one of the number buttons (1to6)
(or press one of the number buttons (1to6) on the remote control).
Direct Access Tuning (using the remote control)
1 Press DIRECT to enter Direct Access Tuning.
2 Press the number buttons to enter a frequency.
3 Press to search for a station.
• To cancel, press or DIRECT.
• If no operation is done for 10seconds after step2, Direct Access Tuning is
automatically canceled.
CLOCK
TIME SYNC ON
:Synchronizes the unit’s time to the Digital Radio signal station
time.;
OFF :Cancels.
Available Program Type for [PTY SEARCH]
SPEECH
: NEWS , AFFAIRS , INFO (information), SPORT , EDUCATE ,
DRAMA , CULTURE , SCIENCE , VARIED , WEATHER , FINANCE ,
CHILDREN , SOCIAL , RELIGION , PHONE IN , TRAVEL , LEISURE ,
DOCUMENT
MUSIC
: POP M (music), ROCK M (music), EASY M (music), LIGHT M
(music),
CLASSICS , OTHER M (music), JAZZ , COUNTRY ,
NATION M (music), OLDIES , FOLK M (music)
The unit will search for the Program Type categorized under
[SPEECH] or [MUSIC] if selected.
• If the volume is adjusted during reception of traffic information,
announcement, alarm or news bulletin, the adjusted volume is
memorized automatically. It will be applied the next time traffic
information, announcement, alarm or news bulletin is turned
on.
DIGITAL RADIO
ENGLISH
JS_KWD_KDC_X7100DAB_XN_EN_3.indd 8JS_KWD_KDC_X7100DAB_XN_EN_3.indd 8 12/14/2016 9:18:26 AM12/14/2016 9:18:26 AM

ENGLISH 9
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Other settings
1 Press the volume knob to enter
[FUNCTION] .
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
XX
TUNER SETTING
LOCAL SEEK ON
: Searches only AM/SW1/SW2 stations with good reception. ;
OFF : Cancels.
• Settings made are applicable only to the selected source/station. Once
you change the source/station, you need to make the settings again.
AUTO
MEMORY
YES :Automatically starts memorizing 6 stations with good reception.;
NO :Cancels.
• Selectable only if [NORMAL] is selected for [PRESET TYPE] . ( 5)
MONO SET ON
:Improves the FM reception, but the stereo effect may be lost.;
OFF :Cancels.
NEWS SET ON : The unit will temporarily switch to News Programme if available. ;
OFF :Cancels.
REGIONAL ON : Switches to another station only in the specific region using the “AF”
control.;
OFF :Cancels.
AF SET ON : Automatically searches for another station broadcasting the same
program in the same Radio Data System network with better reception
when the current reception is poor.;
OFF :Cancels.
TI
*
ON :Allows the unit to temporarily switch to Traffic Information if available
(“TI” lights up).;
OFF :Cancels.
*
[TI] in AM/SW1/SW2 band is for enabling traffic interruption to DIGITAL
AUDIO source only.
PTY SEARCH 1 Turn the volume knob to select the available Program Type (see the
following), then press the knob.
2 Turn the volume knob to select the PTY language ( ENGLISH / FRENCH /
GERMAN ), then press the knob.
3 Press S / T to start searching.
Available Program Type for [PTY SEARCH]
SPEECH : NEWS , AFFAIRS , INFO (information), SPORT , EDUCATE , DRAMA ,
CULTURE , SCIENCE , VARIED , WEATHER , FINANCE , CHILDREN , SOCIAL ,
RELIGION , PHONE IN , TRAVEL , LEISURE , DOCUMENT
MUSIC
: POP M (music), ROCK M (music), EASY M (music), LIGHT M (music),
CLASSICS , OTHER M (music), JAZZ , COUNTRY , NATION M (music),
OLDIES , FOLK M (music)
The unit will search for the Program Type categorized under [SPEECH] or
[MUSIC] if selected.
•
[MONO SET] / [NEWS SET] / [REGIONAL] / [AF SET] / [PTY SEARCH] is selectable only
when the band is FM1/FM2/FM3.
• If the volume is adjusted during reception of traffic information, alarm
or news bulletin, the adjusted volume is memorized automatically. It
will be applied the next time traffic information, alarm or news bulletin
is turned on.
ANALOG RADIO
JS_KWD_KDC_X7100DAB_XN_EN_3.indd 9JS_KWD_KDC_X7100DAB_XN_EN_3.indd 9 12/14/2016 9:18:27 AM12/14/2016 9:18:27 AM

10
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CD/USB/iPod/ANDROID
Start playback
The source changes automatically and playback starts.
CD
*1
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
*2
Do not leave the cable inside the car when not using.
Selectable source: CD/USB 1/USB 2/iPod 1/iPod 2/ANDROID 1/ANDROID 2
To On the faceplate On the remote control
Playback/pause Press . Press .
Reverse/
Fast-forward*4
Press and hold S/T.Press and hold
S/ .
Select a track/file Press S/T. Press S/ .
Select a folder*5Press J/K.Press / .
Repeat play*6Press repeatedly.
TRACK REPEAT / ALL REPEAT : Audio CD
FILE REPEAT / FOLDER REPEAT / ALL REPEAT : MP3/WMA/AAC/WAV/
FLAC file
FILE REPEAT / FOLDER REPEAT / REPEAT OFF : iPod or ANDROID
Random play*6Press repeatedly.
DISC RANDOM / RANDOM OFF : Audio CD
FOLDER RANDOM / RANDOM OFF : MP3/WMA/AAC/WAV/FLAC file,
iPod or ANDROID
Press and hold to select
ALL RANDOM .*7
*3
When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the
instructions to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application
on your Android device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.
*4
For ANDROID: Applicable only when [BROWSE MODE] is selected. ( 11)
*5
For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID.
*6
For iPod/ANDROID: Applicable only when [MODE OFF] / [BROWSE MODE] is selected. ( 11)
*7
For CD: Only for MP3/WMA/AAC files.
USB 1 cable from the
rear of the unit
(USB input terminal).
You can also connect to
the USB 2 cable from
the rear of the unit
(USB input terminal).
ENGLISH
Label side M Eject disc
CA-U1EX (max.: 500mA)
(optional accessory)
Micro USB 2.0 cable
*2
(commercially available)
KCA-iP102/KCA-iP103 (optional
accessory)
*1
or accessory of the
iPod/iPhone
*2
USB
iPod/iPhone
ANDROID*3
JS_KWD_KDC_X7100DAB_XN_EN_3.indd 10JS_KWD_KDC_X7100DAB_XN_EN_3.indd 10 12/14/2016 9:18:27 AM12/14/2016 9:18:27 AM