Keyang DD-1203L-2 User guide

www.keyang.com
DD–1203L–2
EN
DE
NL
ENFR
PL
CORDLESS DRIVER DRILL
(Li-ion Battery)
To reduce the risk of injury,
user must read instruction
manual
ORIGINAL INSTRUCTION MANUAL
EN
2011.12
823-2 Wonsi-dong, Danwon-gu, Ansan-shi, Kyonggi-do, KOREA
Tel : Int+82-31-490-3000 Fax : Int+82-31-490-3019
Disposal of Old Electrical & Electronic Equipment (Applicable in the European
Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be
treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By ensuring
this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product. The recycling of materials
will help to conserve natural resources. For more detailed information about recycling
of this product, please contact your local city office, your household waste disposal
service or the shop where you purchased the product.
ORIGINAL INSTRUCTION MANUAL
ORIGINAL - BETRIEBSANLEITUNG
HANDLEIDING
MODE D’EMPLOI ORIGINAL
ORYGINALNA INSTRUKCJA UŻYTKOWANIA
PROVOZNÍ PŘÍRUČKA
ОРИГИНАЛЬНАЯ ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
MANUAL ORIGINAL DE INSTRUCŢIUNI
EREDETI HASZNÁLATI ÚTMUTATÓ
ORIGINALNO UPUTSTVO ZA UPOTREBU
ОРИГИНАЛНО РЪКОВОДСТВО С ИНСТРУКЦИИ
CZ
RU
RO
HU
SR
BG
MANUALE DI ISTRUZIONI ORIGINALE
ORIGINAL BRUKSANVISNING
ALKUPERÄINEN KÄYTTÖOHJE
ΠΡΩΤΟΤΥΠΟ ΕΓΧΕΙΡΙΔΙΟ ΟΔΗΓΙΩΝ
ORIGINAL INSTRUKTIONSBOG
MANUAL DE INSTRUCCIONES ORIGINAL
ORİJİNAL KULLANIM EL KİTABI
IT
SE
FI
GR
DK
ES
TR

2ILLUSTRATIONS
EN
KEYANG
It is essential that instruction
manual is read before the power
tool is operated for the first time.
Always keeps this instruction manual together
with the power tool.
Ensure that the instruction manual
is with the power tool when it is
given to other persons.
Table of Contents
1. General Power Tool Safety Warnings...............3
2. Specific Safety and Warnings.............................4
3. Check before Use..............................................6
4. Specifications and List of Contents.....................6
5. Noise and vibration............................................7
6. Description of Functions and Applications...........7
7. Operating Instructions.......................................7
8. Maintenance....................................................9
9. Examples of Application..................................9
General Power Tool Safety Warnings
Never modify the plug in any way.
Do not use any adapter plugs with
earthed(gorunded) power tools.
Unmodified plugs and matching outlets will
reduce risk of eteclric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain
or wet codltions.
Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for
outdoor use.
Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing
and use common sense when operating
a power tool. Do not use a power tool
while you are tired or under the in
fluence of drugs, alcohol or medication.
A moment of inattention while operationg
power tools may result in serious
personal injury.
b) Use safety equipment. Always
wear eye protection.
Safety equipment such as dust mask,
non-skid safety shoes, hard hat, or
hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool.
Carrying power tools with your finger on the
switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on.
A wrench or key left attached to a rotating
part of the power tool may result in personal
injury.
WARNING! Read all safety
warning and all instructions.
Failure to follow the warning
instructions may result in electric shock, fire and/or
seroius injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to
your mains -operated (corded) power tool or
battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away
while operating a power tool.
Distractions can cause you to lose
control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Note
As our engineers are striving for the
constant research and development to
develop the quality of products, shape or
structure of our model can be changed
without previous notice.
12
3
4 5 6
7
10 11
9
8
⑧
⑨
①
②③
④
⑤
⑦
⑥

 
KEYANG
EN
CORDLESS DRIVER DRILL
(Li-ion Battery)
It is essential that instruction manual is read

Always keeps this instruction manual together

manual is with the power tool when it is given to
other persons.
Table of Contents




5. Noise and vibration.........................................7

7. Operating Instructions....................................7
8. Maintenance...................................................9

Note
As our engineers are striving for the constant
research and development to develop the quality
of products, shape or structure of our model can
be changed without previous notice.
1.General Power Tool Safety Warnings
WARNING! Read all safety warning and all
instructions. Failure to follow the warning

and/or serious injury. Save all warnings and
instructions for future reference.
The term “power tool” in the warnings refers to
your mains -operated (corded) power tool or
Battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
 
b) Do not operate power tools in explosive
Atmospheres, such as in the presence of
ammable liquids, gases or dust.

the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) Electrical safety
 
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. 
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use residual
current device (RCD) protected supply.

shock.
3) Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the inuence of
drugs, alcohol or medication. A moment
of inattention while operating power tools may
result in serious personal injury.
b) Use safety equipment. Always wear eye
protection. Safety equipment such as dust
mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the o position before
connecting to power source and/or
battery pack, picking up or carrying the
tool.
the switch or energising power tools that have
the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or key left attached to a rotating part
of the power tool may result in personal injury.

ILLUSTRATIONS KEYANG
EN e) Do not overreach. Keep proper footing
and balance at all times.
This enables better control of the power tool

f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used.
Use of dust collection can reduce dust-
related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch
does not turn it on and o.
Any power tool that cannot be controlled
with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
d) Store idle power tools out the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.

untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other
condition that may aect the power tools
operation. If damaged, have the power
tool repaired before use.
Many accidents are caused by poorly
maintained power tools.
 
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed.
 
from those intended could result in a
hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specied
by the manufacturer.
A charger that is suitable for one type of

used with another battery pack.
b) Use power tools only with specically
designated battery pack.
Use of any other battery packs may create a

c) When battery pack is not in use, keep
it away from other metal objects, like
paper clips, coins, keys, nails, screws, or
other small metal objects that can make a
connection from one terminal to another.
Shortening the battery terminals together may

d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, ush with
water. If liquid contacts eyes, additionally
seek medical help.
Liquid ejected from the battery may cause
irritation or burns.
6) Service
a) Have your power tool serviced by a
qualied repair person using only
identical replacement parts.
This will ensure that the safety of the power
tool is maintained.
2. Specic Safety and Warnings
• Do not use the charger under the rain or
when it is wet.
Failure to observe this can cause serious
injury or death due to electric shock.
 Do not insert metal wire or any
conductive object through the ventilating
opening of the charger.
Failure to observe this can cause serious
injury or death due to electric shock.
 Do not attempt to disassemble the
charger and keep the charger out of the
reach of children.

 5
KEYANG
EN
 If the cord of the charger has
been damaged, replace or repair it
immediately. Using the charger with
damaged cord may cause electric shock.
 
 If the cord of the charger has been
damaged, replace or repair it immediately.
Using the charger with damaged cord may
cause electric shock.
 
 Do not throw the battery into the live re.
 
high temperature and cause serious injury.
 Do not short the terminals of the battery If
the terminals of the battery is short circulated,


 Avoid strong impact on the battery and
do not pierce the battery case with a
sharp object.
 
injury.
 Store the battery indoors at 0~40ºC and
avoid direct light and closed hot and
humid places.
 
injury.
 Do not make your ngers and hands
touch with the drill bit during operation.

with the drill bit or caught in it, you may be
injured seriously.
 Do not leave the running tool.
Other operators stayed close to you may be
injured.
 Set the forward/reverse lever in the
neutral position while you are changing
or operating the tool.
 
serious injury by the rotating part of the tool.
 Make sure the battery is attached in the
body of the tool tightly before you start
operation.
 
may be fallen during the operation and cause
an injury in the top of your foot.
 Charge only Keyang approved
rechargeable batteries. Other types of
batteries may burst causing personal
injury and damage.
 Do not disassemble battery.
Incorrect re assembly may result in a risk of

 Accessories may be hot after prolonged
use.
 
contact with skin and use proper protective
gloves when grasping the bit or accessory.
 Keep the battery from being overheated.
If overheated battery is inserted, high
temperature stand by is indicated and
charging can only start after the battery has

overheating due to continuous operation, in
order to protect the battery performance will

 Leaving the battery for a prolonged time
without using it will shorten the life of the
battery.
 
time, charge it completely before storing it.
To use the battery for a long period of time,

 If drill stalls, it is usually because it is
being overloaded or improperly used.
Release trigger immediately.

start a stalled drill. This can damage the drill.
An explanation of any symbols or
pictogram on the tool relevant to
safe use.
Do not use the charger under the rain
or when it is wet.
Failure to observe this can cause serious
injury or death due to electric shock.
Do not insert metal wire or any
conductive object through the
ventilating opening of the charger.
Failure to observe this can cause serious
injury or death due to electric shock.
Do not attempt to disassemble the
charger and keep the charger out of
the reach of children.
If the cord of the charger has been
damaged, replace or repair it
immediately.
Using the charger with damaged cord may
cause electric shock.
Specific Safety and Warnings
working conditions and the work to be
performed.
Use of the power tool for operations different
from those intended could result in a
hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified
by the manufacturer.
A charger that is suitable for one type of
battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically
designated battery pack.
Use of any other battery packs may create a
risk of injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws, or other
small metalobjects that can make a
connection from one terminal to another.
Shorting the battery teminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help.
Liquid ejected from the battery may cause
irritation or burns.
6) Service
a) Have your power tool serviced by a
qualified repair person using only
identical replacement parts.
This will ensure that the safety of the power
tool is maintained.
e) Do not overreach. Keep proper footing
and balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used.
Use of dust collection can reduce dust-related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better
and safer at the rate for which it was designed.
b) Do not use the power tool if the switch
does not turn it on and off.
Any power tool that cannot be controlled with
the switch is dangerous and must be
repaired.
c) Disconnect the plug from the
powersource and/or the battery
pack from the power tool before
making any adjustments,
changing accessories, or
storing power tools.
Such preventive safety measures
reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out the reach of
children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tools operation.
If damaged, have the power tool
repaired before use.
Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these
instructions, taking into account the
Electric shock may cause injury.
Do not use the charger under the rain
or when it is wet.
Failure to observe this can cause serious
injury or death due to electric shock.
Do not insert metal wire or any
conductive object through the
ventilating opening of the charger.
Failure to observe this can cause serious
injury or death due to electric shock.
Do not attempt to disassemble the
charger and keep the charger out of
the reach of children.
If the cord of the charger has been
damaged, replace or repair it
immediately.
Using the charger with damaged cord may
cause electric shock.
Electric shock may cause injury.
Do not throw the battery into the live
fire.
In the fire, the battery may explode due to
high temperature and cause serious injury.
Do not short the terminals of the
battery
If the terminals of the battery is short circuited,
excessive current will flow and fire or
explosion may occur causing serious injury.
Avoid strong impact on the battery
and do not pierce the battery case
with a sharp object.
Fire or explosion may occur causing
serious injury.
Store the battery indoors at 0 ~40
and avoid direct light and closed hot
and humid places.
Fire or explosion may occur causing
serious injury.
Do not make your fingers and hands
touch with the drill bit during
operation.
When your fingers and hands are touched
with the drill bit or caught in it, you may
be injured seriously.
Do not leave the running tool.
Other operators stayed close to you may be
injured.
Set the forward/reverse lever in the
neutral position while you are
changing or operating the tool.
Careless operating of the switch may cause a
serious injury by the rotating part of the tool.
Make sure the battery is attached in
the body of the tool tightly before
you start operation.
When the battery is not attached tightly,
it may be fallen during the operation and
cause an injury in the top of your foot.
Charge only Keyang appoved
rechargeable batteries. Other types
of batteries may burst causing
personal injury and damage
Do not disassemble battery.
Incorrect reassembly may result in a risk of
electric shock, electrocution or fire.
Accessories may be hot after
prolonged use.
When removing the bit from the tool avoid
contact with skin and use proper
protective gloves when grasping the bit or
accessory.
Keep the battery from being
overheated.
If overheated battery is inserted, high
temperature standby is indicated and
charging can only start after the battery has
been cooled down.
When the battery is overheating due to
continuous operation, in order to protect the
battery performance will automatically shut off
the power.
Leaving the battery for a prolonged
time without using it will shorten the
life of the battery.
If the battery is to be stored for a prolonged
time, charge it completely before storing it.
To use the battery for a long period of time,
charge it completely every 3 months.
If drill stalls, it is usually because it is
being overloaded or improperly used.
Release trigger immediately.
Do not click trigger on and off in an attempt to
start a stalled drill. This can damage the drill.
Wear safety helmet
Wear protective gloves
An explanation of any symbols or
pictograms on the tool relevant to safe use
Wear goggles
Wear ear plugs

Return waste material The battery
temperatures over 50
cause damage
Do not incinerate the
battery pack
Do not dispose of
batteries with general
refuse.
V - Volts
V- Direct Current
- Rotation only
- Class construction
V - No load speed
/min - Revolutions or reciprocations
per minute
~ - Alternating current
no
Max. 50
EC Declaration of conformity
We declares that these products meet the standards
EN 60745-1, EN 60745-2-1, EN 60335-1,
EN 60335-2-29, EN 55014-1, EN 55014-2,
EN 61000-3-2 and EN 61000-3-3
( Category )
in compliance with directives 2006/95/EC, 2006/42/EC,
2004/108/EC.
(Legally binding signature of the issuer)
Ki Hwang, Lee
Director of R&D and Quality Assurance
Specifications and List of Contents
10.8
0-350
0-1300
0.8-10
0.8
10
15
6
1. Specifications
2. List of Contents
110-127 / 220-240
50 / 60
10.8
2.6
0.4
Rated voltage [V DC]
Chuck capacity[mm]
Weight(Without battery)[kg]
Model
Items
1st gear
2nd gear
Steel
Wood
Wood screw
Noload speed
[/ min ]
Maximum
capacity
[mm]
Voltage [V DC ]
Capacity [mAh]
Weight [kg]
Tool
Battery
Battery
Charger
DD-1202L-2
Model
BL10801
10.8
1300
0.2
BL10802
10.8
1500
0.2
Input voltage [V AC ]
Input frequency [V AC ]
Output voltage [V DC]
Charging current [A]
Charging time [min]
Weight [kg]
Safety class
30 35
Fabric case
Battery
Battery Charger
Instruction manual
1EA
1or 2EA
1EA
1EA
Description of Functions and Applications
2. Applications
1. Description of Functions
Drilling mode : For drilling in woods, metals,
plastics or other non concrete materials.
Check before Use
Noise and vibration
1. The power source
2. Attachment of the battery
3. Polarity of the battery
4. Trial run
Observe correct main voltage. The voltage
of power source must agree with the
voltage specified in the name plate.
Make sure the rated voltages in the electric
drill and the battery are the same. When the
rated voltage of the battery is higher than
that of the electric drill, the motor can be
damaged by fire.
Before starting the work, wear protection (goggles,
safety helmet, ear plugs, protective gloves) and runthe
tool in the direction avoiding other persons to see if the
tool is operated normaly.
Make sure the battery is attached correctly
before you use the electric tool.
(1) Insert the plug of the charger in the socket, and
the charging indicating lamp will be flickered in
green,red and yellow in turn within one second.
And then, the battery charger will be in the
standby position.
(2) Insert the battery in the battery charger
considering the polarity, and the charging will be
started immediately.
Make sure the battery is attached in the
body of the tool tightly before you start
operation. When the battery is not attached
tightly, it may be fallen during the operation
and cause an injury in the top of your foot.
When the polarity of the battery is not correct,
it may cause the trouble of the switch. Also,
the reversal of the rotating direction can bring
a dangerous situation.
Operating Instructions
1. How to charge the battery
(3) When the battery working time is remarkably
short despite full charging, the life of the battery
may be over. Replace the battery immediately.
A new battery will work properly after five
times of charging and discharging. Charge
and discharge the battery, which is not
used for a long time, for two to three times
to function well.
DD-1202L-2
Battery
Charger
Figure 1
Figure 2
Figure 3
1. Noise and vibration
1) Noise emission
Measured values are according to EN 60745
Power tool
A-weighted sound power level (LWA) [dB(A)]
A-weighted emission level (LpA) [dB(A)]
Uncertainty (K) [dB(A)]
DD-1202L-2
76
65
3
Drilling
mode
Vibration value (ah) [m/s2]
Uncertainty (K) [m/s2]
DD-1202L-2
2.5
1.5
Power tool
method given in EN60745 and may be used
for comparing one tool with another.
The declard vibration total value may also be
used in a preliminary assessment of exposure.
5) A warning
The vibration emission during actual use of
the power tool can differ from the declared
total value depending on the ways in which
the tool is used.
Identify additional safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such
as the times when the tool is switched off and
when it is running idle in addition to the trigger
time).
4) The following information
The declarde vibration total value has been
measured in accordance with a standard test
2) The operator to wear hearing protection
3) Vibration emission
Vibration total values(triaxial vector sum)
determined according to EN 60745
EC Declaration of conformity

standards






3. Check before Use
1. The power source
 
of power source must agree with the voltage

 

voltage of the battery is higher than that of the
electric drill, the motor can be damaged by

2. Attachment of the battery
Make sure the battery is attached correctly
before you use the electric tool.
Make sure the battery is attached in the body
of the tool tightly before you start operation.

may be fallen during the operation and cause
an injury in the top of your foot.
3. Polarity of the battery
 
it may cause the trouble of the switch. Also,
the reversal of the rotating direction can bring
a dangerous situation.
4. Trial run
Before starting the work, wear protection
(goggles, safety helmet, ear plugs, protective
gloves) and run the tool in the direction
avoiding other persons to see if the tool is
operated normally.
4. Specications and List of Contents
1. Specications
 KEYANG
EN
Return waste material The battery
temperatures over 50
cause damage
Do not incinerate the
battery pack
Do not dispose of
batteries with general
refuse.
V - Volts
V- Direct Current
- Rotation only
- Class construction
V - No load speed
/min - Revolutions or reciprocations
per minute
~ - Alternating current
no
Max. 50
EC Declaration of conformity
We declares that these products meet the standards
EN 60745-1, EN 60745-2-1, EN 60335-1,
EN 60335-2-29, EN 55014-1, EN 55014-2,
EN 61000-3-2 and EN 61000-3-3
( Category )
in compliance with directives 2006/95/EC, 2006/42/EC,
2004/108/EC.
(Legally binding signature of the issuer)
Ki Hwang, Lee
Director of R&D and Quality Assurance
Specifications and List of Contents
10.8
0-350
0-1300
0.8-10
0.8
10
15
6
1. Specifications
2. List of Contents
110-127 / 220-240
50 / 60
10.8
2.6
0.4
Rated voltage [V DC]
Chuck capacity[mm]
Weight(Without battery)[kg]
Model
Items
1st gear
2nd gear
Steel
Wood
Wood screw
Noload speed
[/ min ]
Maximum
capacity
[mm]
Voltage [V DC ]
Capacity [mAh]
Weight [kg]
Tool
Battery
Battery
Charger
DD-1202L-2
Model
BL10801
10.8
1300
0.2
BL10802
10.8
1500
0.2
Input voltage [V AC ]
Input frequency [V AC ]
Output voltage [V DC]
Charging current [A]
Charging time [min]
Weight [kg]
Safety class
30 35
Fabric case
Battery
Battery Charger
Instruction manual
1EA
1or 2EA
1EA
1EA
Description of Functions and Applications
2. Applications
1. Description of Functions
Drilling mode : For drilling in woods, metals,
plastics or other non concrete materials.
Check before Use
Noise and vibration
1. The power source
2. Attachment of the battery
3. Polarity of the battery
4. Trial run
Observe correct main voltage. The voltage
of power source must agree with the
voltage specified in the name plate.
Make sure the rated voltages in the electric
drill and the battery are the same. When the
rated voltage of the battery is higher than
that of the electric drill, the motor can be
damaged by fire.
Before starting the work, wear protection (goggles,
safety helmet, ear plugs, protective gloves) and runthe
tool in the direction avoiding other persons to see if the
tool is operated normaly.
Make sure the battery is attached correctly
before you use the electric tool.
(1) Insert the plug of the charger in the socket, and
the charging indicating lamp will be flickered in
green,red and yellow in turn within one second.
And then, the battery charger will be in the
standby position.
(2) Insert the battery in the battery charger
considering the polarity, and the charging will be
started immediately.
Make sure the battery is attached in the
body of the tool tightly before you start
operation. When the battery is not attached
tightly, it may be fallen during the operation
and cause an injury in the top of your foot.
When the polarity of the battery is not correct,
it may cause the trouble of the switch. Also,
the reversal of the rotating direction can bring
a dangerous situation.
Operating Instructions
1. How to charge the battery
(3) When the battery working time is remarkably
short despite full charging, the life of the battery
may be over. Replace the battery immediately.
A new battery will work properly after five
times of charging and discharging. Charge
and discharge the battery, which is not
used for a long time, for two to three times
to function well.
DD-1202L-2
Battery
Charger
Figure 1
Figure 2
Figure 3
1. Noise and vibration
1) Noise emission
Measured values are according to EN 60745
Power tool
A-weighted sound power level (LWA) [dB(A)]
A-weighted emission level (LpA) [dB(A)]
Uncertainty (K) [dB(A)]
DD-1202L-2
76
65
3
Drilling
mode
Vibration value (ah) [m/s2]
Uncertainty (K) [m/s2]
DD-1202L-2
2.5
1.5
Power tool
method given in EN60745 and may be used
for comparing one tool with another.
The declard vibration total value may also be
used in a preliminary assessment of exposure.
5) A warning
The vibration emission during actual use of
the power tool can differ from the declared
total value depending on the ways in which
the tool is used.
Identify additional safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such
as the times when the tool is switched off and
when it is running idle in addition to the trigger
time).
4) The following information
The declarde vibration total value has been
measured in accordance with a standard test
2) The operator to wear hearing protection
3) Vibration emission
Vibration total values(triaxial vector sum)
determined according to EN 60745
Return waste material The battery

cause damage
Do not incinerate the
battery pack
Do not dispose of
batteries with genearl
refuse.


Rotation only

No load speed
Revolutions or reciprocations
per minute
Alternating current
(Legally binding signature of the issuer)
Ki Hwang Lee
Director of R&D and Quality Assurance
Items Model
Tool
 
  
   
   
  
  
  
   


 7
KEYANG
EN
2. List of Contents
5. Noise and vibration
 
 
 
wear hearing protection
 
 
 
 
 
measured in accordance with a standard test
 
used for comparing one tool with another.
The declared vibration total value may also
be used in a preliminary assessment of

5) A warning
 

total value depending on the ways in which
the tool is used.
 
the operator that are based on an estimation

(taking account of all parts of the operating
cycle such as the times when the tool is

addition to the trigger time).
6. Description of Functions and
Applications
1. Description of Functions



2. Applications
Drilling mode : For drilling in woods, metals,
plastics or other non concrete materials.
7. Operating Instructions
1. How to charge the battery
 
and the charging indicating lamp will be

within one second. And then, the battery
charger will be in the stand by position.
(2) Insert the battery in the battery charger
considering the polarity, and the charging will
be started immediately.
Battery
Model  









Battery












 

Fabric case
Battery

Instruction Manual






2






2.5


Drilling
Mode

Uncertatey (k) [m/s2
① Lock sleeve
② Torque adjustment ring
③ Speed selector switch
④ Rotation direction switch
⑤ Housing
⑥ Battery
⑦ On/Off switch
⑧ Work light
⑨ Tool holder

2


8 KEYANG
EN  

discharge the battery, which is not used for
a long time, for two to three times to function
well.

short despite full charging, the life of the
battery may be over. Replace the battery
immediately.
Take care not to short-circuit the terminal
of the battery. The short-circuit of the

doing a serious personal injury.
2. Charging process

Otherwise battery and charger can be damaged by

 
 
 
 
Red Blink : Overheat stand by
(Battery overheated)
 
Be sure to unplug the charger after

2) If charging of the heated battery is attempted
immediately after it has been used or charged,
indicator blinks in red (overheat stand by). After
the cooling, indication changes to red glowing
and charging begins.
 
battery and always keeps the battery in full
charge state.
 
charger. Otherwise battery and charger can
 
error or overheat.
3. Installing and removing battery
 
 
position (locked state).
 
below the handle until the battery securely
latched with a click.
2) Removing.
 
out to remove it.
Always set the rotational direction switch at
centre position when inserting the battery
or changing, carrying or storing the tool.
4. Charge state of the battery
 
battery level indicator for about 2 seconds.




 
5. Work light
 
 
6. Reversing the Rotation Direction
Reversing the rotation direction must be done

direction during operation may damage the tool
 
(for loosening of screw)
 
(for fastening of screw, drilling)
Neutral : Rotation lock (for changing the bit)
7. Adjusting the Speed
 
The power tool switch allows the speed to be
increa
2) Move the speed selector switch
 
2: High speed, low torque
Do not change direction of rotation until
the power tool is at a stand still.
8. Torque setting
 
 
anges by force (torque) adjustment ring.
Low setting range when working with small
screw or at soft working material.
High setting range when working with large
screw or at hard working material.
 
the overload clutch begins to work to keep the

desired torque in the practical work.



7
8
9
5



 9
KEYANG
EN
2) Drilling
 
position.

release the switch, it brings the motor to a
sudden stop. Also, the surplus rotation will be
stopped. It is very convenient for fastening
screws in soft materials processed.The
drill spindle is locked when the switch is not
pressed.
If drill stalls, it is usually because it is
being overloaded or improperly used.
Release trigger immediately. Do not
 
start a stalled drill.
9. Automatic Spindle Lock
This makes quick and easy changing of the
tool in the drill chuck possible.
This makes quick and easy changing of the
tool in the drill chuck possible.
10. Battery Protection
 
continuous operation, in order to protect the
 
the power.
8. Maintenance
Always keep tool and air vent clean for
safe work.
1. Changing Tool
Before you change the tool, you must
remove the battery from the body of the
electric drill or set the rotational
direction switch in lock position
(neutral position).
1) Mounting the Bit
 
 
the end and release the lock sleeve.
2) Removing the Bit
 
while taking out the bit.
2. Environmental Protection
The tool and its accessories contain much
raw materials and plastics that can be recycled
after their life.Therefore, plastic parts are
indicated with their material types so that

material type.
Do not dispose of the battery with home
 
Take care not to short-circuit the terminal of
the battery. The short-circuit of the terminal
may cause a fire or explosion doing a
serious personal injury.
2. Charging process
1) Charging indication
Green Blinks : Before charging
Red Lights : While charging
Green Lights : Charging completed
Red Blink : Overheat standby
(Battery overheated)
Yellow Blinks : Charging impossible
2) If charging of the heated battery is attempted
immediately after it has been used or
charged, indicator blinks in red (overheat
standby). After the cooling, indication
changes to red glowing and charging begins.
3) This charger detects charging status of the
batery and always keeps the battery in full
charge state.
Use only the specified battery and battery
charger. Otherwise battery and charger can
be damaged by fire, explosion,charging
error or overheat.
Be sure to unplug the charger after finishing
the charging.
3. Installing and removing battery
1) Installing.
Set the rotational direction switch at center
position (locked state).
Insert the charged battery into the slot
below the handle until the battery securely
latched with a click.
2) Removing.
Push the battery button once and take it
out to remove it.
4. Charge state of the battery
Pulling the switch trigger will turn on the
battery level indicator for about 2 seconds.
1 = Battery 70 - 100% charged
2 = Battery 30 - 69% charged
3 = Battery less than 30% charged
4 = Battery flat of defective
(Blinking/Turn off)
Always set the rotational direction switch at
center position when inserting the battery
or changing, carrying or storing the tool.
Figure 4
Figure 5
Figure 6
L (Left rotation) : Counterclockwise direction
(for loosening of screw)
R (right rotation) : Clockwise direction
(for fastening of screw, drilling)
Neutral : Rotation lock (for changing the bit)
7. Adjusting the Speed
1) Press the switch
The power tool switch allows the speed to
be increased steplessly up to maximum.
2) Move the speed selector switch
1: Low speed, high torque
2: High speed, low torque
8. Torque setting
1)Screw work
Selection is feasible from among five setting
anges by force (torgue)
adjustment ring.
low setting range when working with small
screw or at soft working material.
high setting range when working with large
screw or at hard working material.
When the tool is reached at the set torque,
the overload clutch begins to work to keep
the tool in the desired torque. You should
set the desired torque in the practical work.
2) Drilling
Set the torque adjustment ring to the drilling
position.( )
The switch has braking function. When you
release the switch, it brings the motor to a
sudden stop. Also, the surplus rotation will
be stopped.
It is very convenient for fastening screws in
soft materials processed.
Do not change direction of rotation until
the power tool is at a stand still.
Reversing the rotation direction must be
done only when the tool is switched off.
Reversing the direction during operation
may damage the tool
6. Reversing the Rotation Direction
Pulling the switch trigger will turn on
the LED light
Figure 10
Figure 11
Figure 9
Figure 8
5. Work light
Figure 7
If drill stalls, it is usually because it is being
overloaded or improperly used. Release
trigger immediately. Do not click trigger on
and off in an attempt to start a stalled drill.
9. Automatic Spindle Lock
The drill spindle is locked when the switch is not
pressed.
This makes quick and easy changing of the tool
in the drill chuck possibble.
10. Battery Protection
When the battery is overheating due to
continuous operation, in order to protect the
battery performance will automatically shut off the
power.
The tool and its accessories contain much
raw materials and plastics that can be
recycled after their life. Therefore, plastic
parts are indicated with their material types so
that they can be classified and recycled for
each material type.
For power tool with type Y attachment: if the
replacement of the supple cord is necesary,
this has to be done by the manufactuer or his
agent in order to avod a safety hazard.
It is very dangerous for customers to
troubleshoot or repair the tool for themselves,
Contact the nearest A/S center (sales agency)
and request for a service
If the replacement of the supply cord is
necessary. this has to be done by the
manufacturer or his agent in order to avoid a
safety hazard.
1) Mounting the Bit
Pull the lock sleeve forward.
Insert a screw driver bit into the tool
holder to the end and release the lock
sleeve.
2) Removing the bit
Keep the lock sleeve pressed forward
while taking out the bit.
Maintenance
Examples of Application
Always keep tool and air ventage clean for
safe work.
The repair shall be requested to the
qualified electric speciailst.
1. Changing tool
2.Environmental Protection
4. Y attachment cord
3. What to do when the tool does not work normally
Before you change the tool, you must remove
the battery from the body of the electric drill or
set the rotational direction swith in lock position
(neutral position).
Do not dispose of the battery with home
garbage or into the fire or river.
Driver Bit
Driver Bit
Magnetic Set
Socket Bit
Power
Screwdriver Set
Drill Bit for
Woodwork
Drill Bit for
Woodwork
Hole Saw
Socket Adaptor
Socket Adaptor
Universal Joint
Socket
Chuck Adaptor
Drill Socket
CORDLESS
DRIVER
DRILL
Socket
 
normally
 
replacement of the supple cord is necessary,
this has to be done by the manufacture or his
agent in order to avoid a safety hazard. It is
very dangerous for customers to trouble shoot

nearest A/S centre (sales agency) and request
for a service.
The repair shall be requested to the
 
 
If the replacement of the supply cord is
necessary. This has to be done by the
manufacturer or his agent in order to avoid a
safety hazard.
9. Examples of Application
Take care not to short-circuit the terminal of
the battery. The short-circuit of the terminal
may cause a fire or explosion doing a
serious personal injury.
2. Charging process
1) Charging indication
Green Blinks : Before charging
Red Lights : While charging
Green Lights : Charging completed
Red Blink : Overheat standby
(Battery overheated)
Yellow Blinks : Charging impossible
2) If charging of the heated battery is attempted
immediately after it has been used or
charged, indicator blinks in red (overheat
standby). After the cooling, indication
changes to red glowing and charging begins.
3) This charger detects charging status of the
batery and always keeps the battery in full
charge state.
Use only the specified battery and battery
charger. Otherwise battery and charger can
be damaged by fire, explosion,charging
error or overheat.
Be sure to unplug the charger after finishing
the charging.
3. Installing and removing battery
1) Installing.
Set the rotational direction switch at center
position (locked state).
Insert the charged battery into the slot
below the handle until the battery securely
latched with a click.
2) Removing.
Push the battery button once and take it
out to remove it.
4. Charge state of the battery
Pulling the switch trigger will turn on the
battery level indicator for about 2 seconds.
1 = Battery 70 - 100% charged
2 = Battery 30 - 69% charged
3 = Battery less than 30% charged
4 = Battery flat of defective
(Blinking/Turn off)
Always set the rotational direction switch at
center position when inserting the battery
or changing, carrying or storing the tool.
Figure 4
Figure 5
Figure 6
L (Left rotation) : Counterclockwise direction
(for loosening of screw)
R (right rotation) : Clockwise direction
(for fastening of screw, drilling)
Neutral : Rotation lock (for changing the bit)
7. Adjusting the Speed
1) Press the switch
The power tool switch allows the speed to
be increased steplessly up to maximum.
2) Move the speed selector switch
1: Low speed, high torque
2: High speed, low torque
8. Torque setting
1)Screw work
Selection is feasible from among five setting
anges by force (torgue)
adjustment ring.
low setting range when working with small
screw or at soft working material.
high setting range when working with large
screw or at hard working material.
When the tool is reached at the set torque,
the overload clutch begins to work to keep
the tool in the desired torque. You should
set the desired torque in the practical work.
2) Drilling
Set the torque adjustment ring to the drilling
position.( )
The switch has braking function. When you
release the switch, it brings the motor to a
sudden stop. Also, the surplus rotation will
be stopped.
It is very convenient for fastening screws in
soft materials processed.
Do not change direction of rotation until
the power tool is at a stand still.
Reversing the rotation direction must be
done only when the tool is switched off.
Reversing the direction during operation
may damage the tool
6. Reversing the Rotation Direction
Pulling the switch trigger will turn on
the LED light
Figure 10
Figure 11
Figure 9
Figure 8
5. Work light
Figure 7
If drill stalls, it is usually because it is being
overloaded or improperly used. Release
trigger immediately. Do not click trigger on
and off in an attempt to start a stalled drill.
9. Automatic Spindle Lock
The drill spindle is locked when the switch is not
pressed.
This makes quick and easy changing of the tool
in the drill chuck possibble.
10. Battery Protection
When the battery is overheating due to
continuous operation, in order to protect the
battery performance will automatically shut off the
power.
The tool and its accessories contain much
raw materials and plastics that can be
recycled after their life. Therefore, plastic
parts are indicated with their material types so
that they can be classified and recycled for
each material type.
For power tool with type Y attachment: if the
replacement of the supple cord is necesary,
this has to be done by the manufactuer or his
agent in order to avod a safety hazard.
It is very dangerous for customers to
troubleshoot or repair the tool for themselves,
Contact the nearest A/S center (sales agency)
and request for a service
If the replacement of the supply cord is
necessary. this has to be done by the
manufacturer or his agent in order to avoid a
safety hazard.
1) Mounting the Bit
Pull the lock sleeve forward.
Insert a screw driver bit into the tool
holder to the end and release the lock
sleeve.
2) Removing the bit
Keep the lock sleeve pressed forward
while taking out the bit.
Maintenance
Examples of Application
Always keep tool and air ventage clean for
safe work.
The repair shall be requested to the
qualified electric speciailst.
1. Changing tool
2.Environmental Protection
4. Y attachment cord
3. What to do when the tool does not work normally
Before you change the tool, you must remove
the battery from the body of the electric drill or
set the rotational direction swith in lock position
(neutral position).
Do not dispose of the battery with home
garbage or into the fire or river.
Driver Bit
Driver Bit
Magnetic Set
Socket Bit
Power
Screwdriver Set
Drill Bit for
Woodwork
Drill Bit for
Woodwork
Hole Saw
Socket Adaptor
Socket Adaptor
Universal Joint
Socket
Chuck Adaptor
Drill Socket
CORDLESS
DRIVER
DRILL
Socket
CORDLESS DRIVER DRILL
(Li-ion Battery)
To reduce the risk of injury,
user must read instruction
manual
ORIGINAL INSTRUCTION MANUAL
EN
2011.12
823-2 Wonsi-dong, Danwon-gu, Ansan-shi, Kyonggi-do, KOREA
Tel : Int+82-31-490-3000 Fax : Int+82-31-490-3019
Disposal of Old Electrical & Electronic Equipment (Applicable in the European
Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be
treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By ensuring
this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product. The recycling of materials
will help to conserve natural resources. For more detailed information about recycling
of this product, please contact your local city office, your household waste disposal
service or the shop where you purchased the product.
