KEYSTONE RIDGE DESIGNS EASTON EA6-6 User manual

TABLE HUBS
(WELDED TO BRACES)
3/8" S.S. FLAT WASHER
3/8" x 2" S.S. HEX
HEAD CAP SCREW
SCREW ASSEMBLY
TYP. 6 PLACES
BRACES
PLEASE READ THESE STEPS BEFORE PROCEEDING
Included with your Easton 6-Seat Table Set is the Following
Hardware:
- Sixty-four (64) 1/2” Stainless Steel Flat Washers
- Thirty (30) 1/2” Stainless Steel Hex Head Nuts
- Thirty (30) 1/2” Stainless Steel Hex Lock Washer
- Thirty (30) 1/2” x 1 1/2” Stainless Steel Hex Head Cap Screws
- Four (4) 3/8” X 1” Stainless Steel Hex Head Cap Screws
- Twelve (16) 3/8” Stainless Steel Flat Washers
- Six (6) 3/8” x 2” Stainless Steel Hex Head Cap Screws
- Six (6) 3/8” Stainless Steel Lock Washers
- Six (6) 3/8” Stainless Steel Hex Head Nuts
ABIDE BY THE FOLLOWING INSTALLATION INSTRUCTIONS
Braces
1. Place braces so plates are approx 60 degrees from each
other.
2. Legs are labeled (B) for bottom, (M) for middle, and (T) for
top.
3. Pick up the brace with marked (M) and place it on top of
brace marked (B). Pick up plate marked (T) and place it on
top of subassembly making sure that the holes in the hubs
line up.
4. Place a 3/8” washer on a 3/8” x 2” cap screw and insert it
through the holes in the hubs.
5. Place 3/8” washer and 3/8” lock washer over threaded end
of cap screw, then add 3/8” nut. Only hand tighten nuts and
bolts on this step.
!
ASSEMBLY INSTRUCTIONS
EASTON 6-SEAT TABLE SET
KEYSTONE RIDGE DESIGNS, INC.
670 Mercer Road | Butler, PA 16001-1840
Toll-free: 1-800-284-8208 | Phone: [phone]
www.keystoneridgedesigns.com

TABLE PLATE
1/2" S.S. HEX
HEAD NUT
1/2" S.S. FLAT WASHER
1/2" x 1 1/2" S.S. HEX
HEAD CAP SCREW
SCREW ASSEMBLY
TYP. 6 PLACES
BRACES
Legs to Table Plate
1. Place table plate on pedestal, aligning the holes on the table
plate with the holes on the pedestal.
2. Add 1/2” washer to 1/2” x 1 1/2” cap screw and insert down
through the hole in the table plate and pedestal/legs.
3. Slide 1/2” washer and 1/2” lock washer over exposed
threads and add 1/2” nut and tighten.
4. After tightening table plate down, tighten brace screws.
Legs / Table Plate Assembly to Table Top
1. Place table top over leg/table plate assembly, making sure
to align the holes in the table mounting plate with the nuts
under the table.
2. Place3/8”atwasherover3/8”x1”hexheadcapscrew
and insert up through holes in mounting plate and thread
into nuts.
3. Tighten hex head cap screws into nuts under table.
(Shown upside down and without legs for clarity.)
ASSEMBLY INSTRUCTIONS (con’t)
EASTON 6-SEAT TABLE SET
KEYSTONE RIDGE DESIGNS, INC.
670 Mercer Road | Butler, PA 16001-1840
Toll-free: 1-800-284-8208 | Phone: [phone]
www.keystoneridgedesigns.com

1/2" S.S. FLAT
WASHER
1/2" x 1 1/2" S.S. HEX
HEAD CAP SCREW
1/2" S.S. HEX HEAD NUT
Seat
1. Place seat on top of pedestal, matching up holes.
2. Add 1/2” washer to 1/2” x 1 1/2” cap screw and insert
through holes in seat and pedestal.
3. Slide 1/2” washer and 1/2” lock washer over exposed
threads and add 1/2” nut and tighten.
After all parts are assembled, tighten all nuts and bolts.
ASSEMBLY INSTRUCTIONS (con’t)
EASTON 6-SEAT TABLE SET
KEYSTONE RIDGE DESIGNS, INC.
670 Mercer Road | Butler, PA 16001-1840
Toll-free: 1-800-284-8208 | Phone: [phone]
www.keystoneridgedesigns.com