Keystone KoolSpot Silver Series User manual

KoolSpot Silver Series Solar Shades
Description Part Number Qty Included
Clutch Bracket CB8 1
Stationary Bracket SB8 1
Plastic Bracket Covers PBC8 2
Top Tube Clutch Plug TTCP8 1
Top Tube Stationary Plug TTSP8 1
Bottom Rail BR8 1
Bottom Rail Caps BRC8 2
Chain CH8 1
Shade SE8 1
Screws SCR8 5
Tension Device TDE8 1
Tools required: phillips screwdriver, leveling device (lazer level, standard level, etc.), and
power drill (if pre-drilling the holes).
INSTALLATION INSTRUCTIONS
Warranty and maintenance
To clean your KoolSpot shade simply rinse with water and scrub with any non-abrasive
cleaner (using bleach or other abrasive cleaners will void your warranty). Roll the shade
down to air dry.
Your KoolSpot Solar Shade fabric has a warranty of three (3) years.
Step 5: Install tension device
The Tension Device keeps the chain secure and
reduces the risk of strangulation.
Install the Tension Device in a location that
keeps the chain taught (see Fig. K).
Place the chain in the Tension Device, then
snap it closed. Attach the Tension Device to the
wall.
303.652.6164 (p)
www.KeystoneFabrics.com
Figure K
Congratulations on the purchase of your KoolSpot Solar Shade. Please read these instructions
carefully prior to installing your shade. Please call if you have any questions regarding
installation or if you are missing any parts.
Adjusting chain tension
Figure L
If the chain tension is
too tight or too loose
when you raise or
lower your shade, the
tension of your chain
can be adjusted.
Simply remove
the Plastic Bracket
Cover from the Clutch
Bracket and loosen the
screws to loosen chain
tension. Tighten
screws to tighten chain
tension (see Fig. L).
Clutch Bracket
(CB8)
Stationary Bracket
(SB8)
Top Tube Clutch Plug
(TTCP8)
Figure A
Bottom Rail
(BR8)
Bottom Rail Caps
(BRC8)
Chain
(CN8)
Shade
(SE)
Plastic Bracket Cover
(PBC8)
Plastic Bracket Cover
(PBC8)
12/07
Top Tube Stationary Plug
(TTSP8)
Tension Device
(TD8)
Loosen all screws
Replace the Plastic Bracket Cover.

Step 1: Determine type of installation
Be sure to mount the brackets to a wood stud. If a wood stud cannot be located, an anchor
must be used (see your local hardware store for assistance).
Make sure your brackets are secure before proceeding to Step 3.
Step 3: Install brackets
Step 2: Mark holes for installation
Before you can hang your solar shade, it will help to mark the holes where you will put
your screws. Figure G will help you determine where your holes should be located.
Shade size Screw to screw
measurement
Total width
(installed)
Approximate
weight
48’’ 48’’ 49 9/16” 3.1 lbs
72’’ 72’’ 73 9/16’’ 4.3 lbs
96’’ 96’’ 97 9/16’’ 5.6 lbs
120’’ 120’’ 121 9/16’’ 6.8 lbs
Secure the Clutch Bracket and Stationary
Bracket with the provided wood screws
(see Fig. H).
Do not tighten screws completely yet.
1. First, insert the Top Tube
Clutch Plug into the Clutch
Bracket.
2. Second, slide the Top Tube
Stationary Plug into the
Stationary Clutch Bracket.
Close the latch on the
Stationary Plug (see Fig. I).
Adjust the brackets snugly to
the solar shade so the solar
shade is secure (Fig. J).
Tighten screws.
WALL MOUNT
There are two (2) ways to install your solar shade (see Fig. B and C). Your solar shade
comes ready for a wall installation (Fig. B). If you prefer a wall installation (Fig. B), you
are ready to proceed to Step 2.
If you want to change your solar shade so it hangs from the top/ceiling (ceiling mount, see
Fig. C), you will need to make a change before proceeding to Step 2. Please see below if
you want to change to a Ceiling Mount.
CEILING MOUNT
Figure B
Figure C
CHANGING TO CEILING MOUNT
To change to a ceiling mount, you
will need to remove the Plastic
Bracket Covers and remove all
screws (see Fig. D) from the Clutch
Bracket and Stationary Bracket.
Figure D
Step 4: Install solar shade
Figure H
Figure I
Figure G
Figure J
Figure E Figure F
After removing the screws, change
the Clutch Bracket so it matches
Figure F, and change the
Stationary Bracket so it matches
Figure E.
Replace the screws and Plastic
Bracket Covers when nished.