KI CFS01 User manual

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Mounting Pole to Worksurface
using the Clamp Mounting System
Note: The monitor arm kit comes
with two different length bolts, 31/2”
and 51/2” long. The clamp mounting
system detailed below uses the 31/2”
bolt.
1. Insert clamp knob onto the 31/2” long
clamp bolt and tap the bolt head into
the recess in the knob, ensuring the
bolt head is securely engaged into
the knob (Figure 1).
2. Twist the knob with clamp bolt
through the threaded hole in
the lower clamp bracket. Set the
U-shaped bracket onto the end of
the clamp bolt, aligning the center
hole in the bracket with the threaded
hole in the end of the clamp bolt
as illustrated. Using the bracket
assembly screw provided, insert it
through the U-shaped bracket and
twist it into the clamp bolt. Do not
tighten screw completely, allowing
for the U-shaped bracket to rotate on
the end of the clamp bolt
(Figures 1 & 2).
3. Hook the lower clamp bracket
assembly into one of the top two (of
the three) positions on the upper
clamp bracket, appropriate to the
worksurface thickness (Figure 2).
4. Position the clamp bracket and
pole assembly onto the edge of the
worksurface at the desired location.
Using the clamp knob, and holding
the U-shaped bracket in position as
illustrated, tighten to secure pole
assembly to the worksurface
(Figure 3).
3/”
clamp
bolt
1
2
clamp
knob
lower
clamp
bracket
Figure 1
U-shaped
bracket
bracket
assembly
screw
Figure 2
lower clamp
bracket
assembly
pole
assembly
upper
clamp
bracket
pole assembly
Figure
3
worksurface
clamp
bracket
clamp
knob
Assembly Instructions
Monitor Arms
Models CFS01, CFS02, CFS03, CFS04, CFS05, CFS06 & CFS07
August 2021

2
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Mounting Pole to Worksurface - Drill Mounting System
Assembly Instructions
Figure
1
pole
assembly
upper
clamp
bracket
Phillips
screw
worksurface
(top)
drill
grommet
cutout
Figure
4
Mounting Pole to Worksurface
using the Drill Mounting System
Note: Drilling a hole through the
worksurface to mount the pole
assembly is an option when the pole
assembly cannot mount to the edge
of the worksurface.
1. Using a Phillips screwdriver, remove
screws attaching the upper clamp
bracket to the pole assembly base
(Figure 1). Set the upper clamp
bracket aside and re-attach screws to
the pole assembly base (Figure 2).
Note: The upper clamp bracket is
used as a template to field locate
where the pole assembly will mount
and to make sure no interference is
present once installed. The bracket
can be oriented side-to-side (with the
flange to face the left or right table
sides) or front-to-back, as long as
the flange faces the user side.
2. Using the upper clamp bracket as a
template underneath the worksurface,
position the bracket’s drill mounting
hole a minimum of 3” away from
the grommet cutout edge and a
minimum of 21/2” from the non-user
edge of the worksurface and mark
the location. To prevent the laminate
from peeling, place a piece of tape
over the marked location, then
re-mark desired location on the piece
of tape. Use a 1/4” drill bit in a drill
driver and carefully bore a pilot hole
straight up at the marked location,
all the way through the worksurface
(Figure 3).
3. On the worksurface top, place a piece
of tape over the pilot hole to prevent
the laminate from peeling and mark
hole location. Drill down through
the pilot hole using a 3/8” drill bit in
a drill driver until it goes all the way
through the worksurface (Figure 4).
Figure
2
pole
assembly
Phillips
screw
Figure
3
grommet
cutout
worksurface
(underside)
upper
clamp bracket
(front-to-back
orientation)
flange
drill-mounting
hole
drill

3
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Mounting Pole to Worksurface - Drill Mounting System
Assembly Instructions
Note: The monitor arm kit comes
with two different length clamp
bolts, 31/2” and 51/2” long. The Drill
Mounting System below uses 51/2”
bolt.
4. Flip upper clamp bracket upside
down as illustrated in Figures 5 & 6
and position the upper clamp bracket
side-to-side (Figure 5) (with the
flange to face the left or right table
sides) or front-to-back (Figure 6)
over the drilled mounting hole as
illustrated, align and hold in place
from under the worksurface
(Figures 5 & 6).
Note: If upper clamp bracket is
oriented in the front-to-back position
as illustrated in Detail A and a
10-wire rigid wireway is present,
the end of the bracket without the
flange can slide above the wireway
into mounting position as long as it
does not interfere with the electrical
system (Detail A).
5. Slide the clamp knob onto the 51/2”
long clamp bolt and tap the bolt head
into the recess in the knob, ensuring
the bolt head is securely engaged
into the knob (Figures 5 & 6).
6. Install the clamp bolt and knob
assembly through the mounting
hole of the upper clamp bracket then
through the drilled mounting hole
(Figures 5 & 6).
7. Position the pole assembly above the
mounting hole with clamp bolt. Align
and twist the threaded end of the bolt
into the pole assembly base, using
the clamp knob to tighten securely
(Figures 5 & 6).
Figure
5
grommet
cutout
pole
assembly
worksurface
(underside)
upper clamp
bracket
(side-to-side)
clamp
knob
5 /”
1
2
clamp
bolt
Figure
6
grommet
cutout
pole
assembly
worksurface
(underside)
upper clamp
bracket
(front-to-back)
clamp
knob
5 /”
1
2
clamp
bolt
Detail
A
upper clamp
bracket
pole
assembly
clamp
knob
5 /”
1
2
clamp
bolt
10-wire
rigid
wireway

4
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Monitor Mount to Extension Arm Assembly
Assembly Instructions
Monitor Mount Assembly to
Extension Arm Assembly
Important: If model includes
extension arms, follow steps 1
through 7 to install monitor mount
assembly to the extension arm
assembly.
1. Set plastic bearing onto the opening
on the extension arm (Figure 1).
2. Making sure the arrow symbol on
the faceplate of the monitor mount
assembly is facing up, place monitor
mount on top of the plastic bearing
of the extension arm (Figure 2).
3. Set bore cup and toothed locking
washer into the monitor mount
opening. Insert joint bolt through the
bore cup, toothed locking washer
and extension arm (Figure 3).
4. Insert second bore cup, plastic
washer, and metal washer through
the joint bolt on the underside of the
extension arm. Thread joint nut onto
the joint bolt (Figure 4).
5. Take 9/16” socket wrenches to top of
joint bolt and bottom joint nut and
tighten to the required tension.
6. Install joint cap onto the opening of
the monitor mount (Figure 5).
7. Screw cable manager onto joint
bolt located on the underside of the
extension arm (Figure 5).
plastic
bearing
Figure
1
extension ar
m
assembly extension ar
m
assembly
plastic
bearing
Figure
2
monitor mount
assembly
faceplate
Figure
3
monitor mount
bore
cup
toothed locking
washer
joint
bolt
extension ar
m
assembly
Figure
4
bore
cup
metal
washer
plastic
washer
extension ar
m
assembly
joint nut
Figure
5
extension ar
m
assembly
joint cap
cable
manager

5
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Single Screen Monitor Arm - Model CFS01
Assembly Instructions
pole assembly
Figure 1
worksur
face
pole cap
mounting system
(clamp mounting
shown)
pole assembly
Figure
2
support
ring
worksur
face
pole assembly
Figure 3
support
ring
worksurface
monitor mount
assembly
(includes bushing)
trim ring
pole cap
pole assembly
Figure 4
support
ring
worksurface
monitor
cables
support
ring tab
Single Screen Monitor Arm
Assembly - Model CFS01
1. If pole assembly mounting systems
have not been installed, reference
“Clamp Mounting Systems”
instructions on page 1, or “Drill
Mounting Systems” instructions on
page 2 before continuing (Figure 1).
2. Twist the pole cap off the pole
assembly, but save to place back on
pole once all components have been
installed (Figure 1).
3. Slide the support ring down the pole
to the desired height of the monitor
screen. Twist the knob on the support
ring to secure in place (Figure 2).
4. Place monitor mount assembly down
the pole on top of the support ring
(Figure 3).
5. Mount the trim ring on top of the
monitor mount assembly followed by
re-installing the pole cap on top of
the pole assembly (Figure 3).
6. Insert monitor cables through
support ring tabs as required
(Figure 4).
7. To properly install monitor screen to
the faceplate of the monitor mount
assembly, reference “Mounting the
Monitor” instructions on page 17.

6
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Dual Screen Monitor Arm - Model CFS02
Assembly Instructions
Dual Screen Monitor Arm
Assembly - Model CFS02
1. If pole assembly mounting systems
have not been installed, reference
“Clamp Mounting Systems”
instructions on page 1, or “Drill
Mounting Systems” instructions on
page 2 before continuing (Figure 1).
2. Twist the pole cap off the pole
assembly, but save to place back on
pole once all components have been
installed (Figure 1).
3. Slide the dual hub support ring
down the pole to the desired height
of the monitor screen. Twist knob on
the support ring to secure in place
(Figure 2).
4. Place the dual hub arm assembly
down the pole into position on top of
the dual hub support ring (Figure 2).
5. Mount the trim ring on top of the
dual hub arm assembly followed by
re-installing the pole cap on top of
the pole assembly (Figure 3).
6. Insert monitor cables through
support ring tabs as required
(Figure 4).
7. To properly install monitor screen to
the faceplate of the monitor mount
assembly, reference “Mounting the
Monitor” instructions on page 17.
pole
assembly
worksur
face
pole cap
mounting system
(clamp mounting
shown)
Figure 1
Figure 2
dual hub
support
ring
pole
assembly
worksurface
dual hub ar
m
assembly
front plate
Figure 3
pole
assembly
worksurface
dual hub
support ring
pole cap
trim ring
dual hub arm
assembly

7
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Single Screen Monitor Arm - Model CFS03
Assembly Instructions
Single Screen Monitor Arm
Assembly - Model CFS03
1. If pole assembly mounting systems
have not been installed, reference
“Clamp Mounting Systems”
instructions on page 1 or “Drill
Mounting Systems” instructions on
page 2 before continuing (Figure 1).
2. If monitor mount assembly has
not been installed to the Model
CFS03 extension arm assembly,
reference “Monitor Mount Assembly
to Extension Arm Assembly”
instructions on page 4 before
continuing.
3. Twist the pole cap off the pole
assembly, but save to place back on
pole once all components have been
installed (Figure 1).
4. Slide the support ring down the pole
to the desired height of the monitor
screen. Twist the knob on the support
ring to secure in place (Figure 2).
5. Place the Model CFS03 extension
arm assembly down the pole into
position on top of the support ring
(Figure 3). Tighten the set screw
in the extension arm assembly for
correct tension to pole assembly
(Detail A).
6. Mount the trim ring on top of the
extension arm assembly (Figure 3).
7. Repeat process following steps
1 through 6 above for mounting
additional monitors, then insert the
pole cap on top of the pole assembly
(Figure 3).
Note: Maximum allowed weight of
monitor screen is 20 lb per monitor
mount.
pole assembly
Figure 1
worksurface
pole cap
mounting system
(clamp mounting
shown)
pole
assembly
support
ring
worksur
face
Figure 2
pole assembly
Figure 3
support
ring
worksurface
Model CFS03
extension arm
assembly
trim ring
pole cap
3/”
16
Allen key
monitor
mount
Detail A
3/”
16
Allen key
set
screw
Model CFS03
extension arm assembly

8
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Single Screen Monitor Arm - Model CFS03
Assembly Instructions
Figure 6
cable manager
release tabs height-adjust ar
m
cable manager
Model CFS03
extension arm
assembly
joint cable
manager
Figure 8
Detail B
cable manager
release tab height-adjust ar
m
cable manager
Figure
7height-adjust arm
cable manager
monitor
cable
monitor mount
assembly Model CFS03
extension arm
assembly
Figure 9
support
ring
worksurface
monitor
cable
support
ring tab
Model CFS03
extension arm
assembly
joint cable
manager
Figure
4
support
ring
worksurface
monitor
cable
support
ring tab
Model CFS03
extension arm
assembly
monitor mount
assembly
Figure
5
worksurface
monitor
cable
Model CFS03
extension arm
assembly
joint cable
manager
cable
manager
suppor
t
ring tab
Single Screen Monitor Arm
Assembly - Model CFS03 (cont.)
8. Insert monitor cables through
support ring tabs (Figure 4). If
monitor cables will be routed
through optional height-adjust arm
cable, proceed to “Height-Adjust Arm
Cable Manager” instructions below,
otherwise feed the monitor cables
through joint cable managers located
on the underside of extension arm
assembly (Figure 5).
9. To properly install monitor screen to
the faceplate of the monitor mount
assembly, reference “Mounting the
Monitor” instructions on page 17.
Height-Adjust Arm Cable Manager
(optional)
1. To remove the height-adjust arm
cable manager, pinch the two release
tabs on the cable manager located on
the underside of the Model CFS03
extension arm assembly (Figure 6).
2. Lay cables in height-adjust arm cable
manager (Figure 7).
3. Snap cable manager back to the
underside of the extension arm
assembly taking note the text
“FRONT” inside the cable manager
(Figure 8 & Detail B).
4. Feed monitor cables through joint
cable managers located on the
underside of extension arm assembly
(Figure 9).
5. To properly install monitor screen to
the faceplate of the monitor mount
assembly, reference “Mounting the
Monitor” instructions on page 17.

9
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Single Screen, Double Extension Monitor Arm - Model CFS04
Assembly Instructions
Single Screen, Double Extension
Monitor Arm Assembly - Model
CFS04
1. If pole assembly mounting systems
have not been installed, reference
“Clamp Mounting Systems”
instructions on page 1 or “Drill
Mounting Systems” instructions on
page 2 before continuing (Figure 1).
2. If monitor mount assembly has
not been installed to the Model
CFS04 extension arm assembly,
reference “Monitor Mount Assembly
to Extension Arm Assembly”
instructions on page 4 before
continuing.
3. Twist the pole cap off the pole
assembly, but save to place back on
pole once all components have been
installed (Figure 1).
4. Slide the support ring down the pole
to the desired height of the monitor
screen. Twist the knob on the support
ring to secure in place (Figure 2).
5. Place the Model CFS04 extension
arm assembly down the pole into
position on top of the support ring
(Figure 3). Tighten the set screw
in the extension arm assembly for
correct tension to pole assembly
(Detail A).
6. Mount trim ring on top of the
extension arm assembly (Figure 3).
7. Repeat process following steps 1
through 6 for mounting additional
monitors, then insert the pole cap on
top of the pole assembly (Figure 3).
Note: Maximum allowed weight of
monitor screen is 20 lb per monitor
mount.
Figure 1
pole
assembly
worksur
face
pole cap
mounting system
(clamp mounting
shown)
Figure
2
pole
assembly
worksur
face
support
ring
Figure 3
pole
assembly
worksur
face
support
ring
trim
ring
pole cap
Model CFS04
extension arm
assembly
Detail A
3/”
16
Allen key
set
screw
Model CFS04
extension arm
assembly
monitor
mount

10
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Singe Screen, Double Extension Monitor Arm - Model CFS04
Assembly Instructions
Figure 4
pole
assembly
worksurface
support
ring
support
ring tab
Model CFS04
extension arm
assembly
monitor
cable
Figure 5
cable manager
release tabs
height-adjust ar
m
cable manager
Model CFS04
extension arm
assembly
joint cable
manager
Figure 7
Detail B
cable manager
release tab height-adjust arm
cable manager
Figure
6height-adjust arm
cable manager
monitor
cable
Model CFS04
extension arm
assembly
Figure 8
monitor
cable
cable
manager
Model CFS04
extension arm
assembly
Single Screen, Double Extension
Monitor Arm Assembly - Model
CFS04 (cont.)
8. Insert monitor cables through
support ring tabs (Figure 4).
Height-Adjust Arm Cable Manager
1. To remove the height-adjust arm
cable manager, pinch the two release
tabs on the cable manager located on
the underside of the Model CFS04
extension arm assembly (Figure 5).
2. Lay cables in height-adjust arm cable
manager (Figure 6).
3. Snap cable manager back to the
underside of the extension arm
assembly taking note the text
“FRONT” inside the cable manager
(Figure 7 & Detail B).
4. Feed monitor cables through cable
managers located on the underside
of the extension arm assembly
(Figure 8).
5. To properly install monitor screen to
the faceplate of the monitor mount
assembly, reference “Mounting the
Monitor” instructions on page 17.

11
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Dual Screen, Two Monitor Arms - Model CFS05
Assembly Instructions
Dual Screen, Two Monitor Arms -
Assembly - Model CFS05
1. If pole assembly mounting systems
have not been installed, reference
“Clamp Mounting Systems”
instructions on page 1 or “Drill
Mounting Systems” instructions on
page 2 before continuing (Figure 1).
2. If monitor mount assembly has not
been installed to the dual hub arm
assembly, please reference “Monitor
Mount Assembly to Extension Arm
Assembly” instructions on page 4
before continuing.
3. Twist the pole cap off the pole
assembly, but save to place back on
pole once all components have been
installed (Figure 1).
4. Slide the dual hub support ring
down the pole to the desired height
of the monitor screen. Twist knob on
the support ring to secure in place
(Figure 2).
5. Place the dual hub arm assembly
down the pole into position on top of
the dual hub support ring (Figure 2).
Tighten the set screw in the arm
assembly for correct tension to pole
assembly (Detail A).
6. Mount the trim ring on top of the
dual hub assembly followed by
re-installing the pole cap on top of
the pole assembly (Figure 3).
Note: Maximum allowed weight of
monitor screen is 20 lb per monitor
mount.
pole
assembly
worksurface
pole cap
mounting system
(clamp mounting
shown)
Figure 1
Figure 2
dual hub
support
ring
pole
assembly
worksurface
dual hub
assembly
front plate
dual hub arm
assembly
Figure 3
dual hub
support ring
pole
assembly
worksurface
dual hub arm
assembly
pole cap
trim ring
3/”
16
Allen
key
set
screw
Detail A
Model
CFS0 arm5
assembly

12
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Dual Screen, Two Monitor Arms - Model CFS05
Assembly Instructions
Dual Screen, Two Monitor Arms -
Assembly - Model CFS05 (cont.)
7. Insert monitor cables through
support ring tabs (Figure 4).
Arm Cable Manager
1. To remove the arm cable manager,
pinch the two release tabs on the
cable manager located on the
underside of the Model CFS05 arm
assembly (Figure 5).
2. Lay cables in arm cable manager
(Figure 6).
3. Snap cable manager back to the
underside of the arm assembly taking
note the text “FRONT” inside the
cable manager (Figure 6).
4. Feed monitor cables through joint
cable managers located on the
underside of arm assembly
(Figure 7).
5. To properly install monitor screen to
the faceplate of the monitor mount
assembly, reference “Mounting the
Monitor” instructions on page 17.
Figure 5
cable
manager
release tabs
cable
manager
joint cable
manager
Model CFS05
arm assembly
Figure 6
cable
manager
monitor
cable
Model CFS05
arm assembly
cable manager
release tab
Figure 7
monitor
cable
Model CFS05
arm assembly
joint cable
manager
Figure
4
support
ring tab
pole
assembly
worksurface
dual hub
support ring
monitor
cable
Model CFS05
arm assembly

13
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Dual Screen, Two Double Extension Monitor Arms - Model CFS06
Assembly Instructions
pole
assembly
worksurface
pole cap
mounting system
(clamp mounting
shown)
Figure
1
Figure 2
dual hub
support
ring
pole
assembly
worksur
face
dual hub arm
assembly
front plate
dual hub arm
assembly
Figure 3
dual hub
support ring
pole
assembly
worksurface
dual hub arm
assembly
pole cap
trim ring
Dual Screen, Two Double
Extension Monitor Arm
Assembly - Model CFS06
1. If pole assembly mounting systems
have not been installed, reference
“Clamp Mounting Systems”
instructions on page 1 or “Drill
Mounting Systems” instructions on
page 2 before continuing (Figure 1).
2. If monitor mount assembly has not
been installed to the dual hub arm
assembly, please reference “Monitor
Mount Assembly to Extension Arm
Assembly” instructions on page 4
before continuing.
3. Twist the pole cap off the pole
assembly, but save to place back on
pole once all components have been
installed (Figure 1).
4. Slide the dual hub support ring
down the pole to the desired height
of the monitor screen. Twist knob on
the support ring to secure in place
(Figure 2).
5. Place the dual hub arm assembly
down the pole into position on top of
the dual hub support ring (Figure 2).
Tighten the set screw in the arm
assembly for correct tension to pole
assembly (Detail A).
6. Mount the trim ring on top of the
dual hub assembly followed by
re-installing the pole cap on top of
the pole assembly (Figure 3).
Note: Maximum allowed weight of
monitor screen is 20 lb per monitor
mount.
3/”
16
Allen key
set
screw
Detail A

14
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Dual Screen, Two Double Extension Monitor Arms - Model CFS06
Assembly Instructions
Figure
5
Model CFS06
arm assembly
cable
manager
cable manager
release tab
joint cable
manager
Figure
6
Model CFS06
arm assembly
cable
manager
monitor
cable
Figure 7
monitor
cable
joint cable
manager
Model CFS06
arm assembly
Figure 4
dual hub
support ring
pole
assembly
worksurface
dual hub arm
assembly
Model CFS06
arm assembly
monitor
cable
Dual Screen, Two Double
Extension Monitor Arm
Assembly - Model CFS06 (cont.)
7. Insert monitor cables through
support ring tabs (Figure 4).
Arm Cable Manager
1. To remove the arm cable manager,
pinch the two release tabs on the
cable manager located on the
underside of the Model CFS06 arm
assembly (Figure 5).
2. Lay cables in arm cable manager
(Figure 6).
3. Snap cable manager back to the
underside of the arm assembly taking
note the text “FRONT” inside the
cable manager (Figure 6).
4. Feed monitor cables through joint
cable managers located on the
underside of arm assembly
(Figure 7).
5. To properly install monitor screen to
the faceplate of the monitor mount
assembly, reference “Mounting the
Monitor” instructions on page 17.

15
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Triple Screen Monitor Arm - Model CFS07
Assembly Instructions
pole
assembly
worksur
face
pole cap
mounting system
(clamp mounting
shown)
Figure 1
worksurface
mounting system
(clamp mounting
shown)
Figure 2
pole
assembly
hub
bushing
half
hub
bushing
half
beam
half
beam
half
beam
screw beam
screw
beam
lock nut
bushing
tab
beam
lock nut
Triple Screen Monitor Arm
Assembly - Model CFS07
1. If pole assembly mounting systems
have not been installed, reference
“Clamp Mounting Systems”
instructions on page 1 or “Drill
Mounting Systems” instructions on
page 2 before continuing (Figure 1).
2. If monitor mount assembly has
not been installed to the extension
arm assembly, reference “Monitor
Mount Assembly to Extension Arm
Assembly” instructions on page 4
before continuing.
3. Twist the pole cap off the pole
assembly, but save to place back on
pole once all components have been
installed (Figure 1).
4. To install beam halves to the pole
assembly, first position two hub
bushing halves together around the
pole, with the bushing tabs facing
the user side as illustrated. Next
orient the two beam halves over the
hub bushing halves, aligning the
user side beam mount holes with
the holes in the bushing tabs. Insert
a beam screw through all aligned
mounting holes at the user side
and twist on a beam lock nut. Add
a screw and beam lock nut at the
rear, then tighten back screw and
nut. Position the beam to the desired
height and tighten user side beam
screw and lock washer to secure
beam assembly in place (Figure 2).

16
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Triple Screen Monitor Arm - Model CFS07
Assembly Instructions
Triple Screen Monitor Arm
Assembly - Model CFS07 (cont.)
5. To prepare extension arm
assemblies for installation to the
beam, first screw a spacer onto the
threaded end of the set screw on
the underside of each bushing cap
(Figure 3).
6. Insert arm joint bushing into the
underside opening on the extension
arm assembly. Then install a
bushing cap with spacer into the
top openings (Figure 3).
7. Using the spacers located on the
underside of the bushing caps,
slide extension arm assembly
into the “T” slots on top of beam
assembly. Tighten set screw on
top of the bushing cap to secure
monitor assembly in place
(Figure 4).
8. Slide the support ring down the
pole to the desired height of the
monitor screen. Twist the knob on
the support ring to secure in place
(Figure 4).
9. Place monitor mount assembly
down the pole on top of the support
ring (Figure 4).
bushing
cap
spacer
Figure
3
extension ar
m
assembly
arm joint
bushing
(beam)
set
screw
beam assembly
bushing cap
with spacer
extension arm
assembly
Figure 4
pole
assembly
support
ring
monitor
cable
support
ring tab
“T” slot
on top of
beam
“T” slot
on backside
of beam
monitor
cable support
ring tab
Detail
B
monitor mount
assembly
extension arm
assembly
pole cap
trim ring
10. Mount the trim ring on top of the
monitor mount assembly followed
by re-installing the pole cap on top
of the pole assembly (Figure 4).
11. Slide beam cable managers into
the “T” slots on the backside of the
beam assembly as illustrated. Then
install beam end cap on to each end
of the beam assembly (Detail A).
12. Insert monitor cables through
support ring tabs. Next, feed
monitor cables through beam cable
managers installed on the backside
of the beam assembly (Figure 4 &
Detail B).
13. To properly install monitor
screen to the faceplate of the
monitor mount assembly,
reference “Mounting the Monitor”
instructions on page 17.
Detail A
beam
cable
manager beam
end cap
“T” slot
on backside
of beam

17
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Mounting the Monitor
Assembly Instructions
Mounting the Monitor
Note: Maximum allowed weight of
monitor screen is 20 lb per monitor
mount.
1. Orient the quick connect bracket so
that the arrow symbol points up.
Secure bracket to the back of the
monitor screen using the mounting
screws supplied by the user
(Figure 1).
2. Making sure the arrow symbol on
the faceplate of the monitor mount
assembly is facing up, slide connect
bracket onto faceplate until the
bottom tab of the connect bracket
clicks onto the faceplate (Figure 2).
3. To remove the monitor, depress
tab on the quick connect bracket
and remove from monitor mount
assembly (Figure 2).
4. If the monitor lowers or is too tight,
adjust the tension screw at the side
of the head of the monitor mount
assembly as shown using a 3/16”
Allen key (Figure 2).
quick connect
bracket
Figure
1
mounting
screws
(user supplied)
monitor
Figure 2
3/”
Allen key
16
quick connect
bracket
monitor
mount
assembly
faceplate
monitor
tab
tension
screw

18
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Monitor Arms - Height and Torque Adjustments
Assembly Instructions
Adjusting the Height-Adjustable
Segment
1. Remove the plastic shroud on
the side of the height-adjustable
segment (Figure 1).
2. With the monitor mounted to the
arm, move the monitor through the
height range; Ensure the arm will
hold the monitor in the position you
placed it (Figure 2).
3. If the monitor lowers or rebounds
upward, adjust the tension screws
at the front and back of the arm
segment as shown using the 3/16”
Allen key. Repeat steps until the
monitor is counterbalanced
(Figure 2).
Adjusting the Torque
1. Remove joint cap from the top of
the joint using a small flat head
screwdriver (Figure 3).
2. Unscrew the cable manager from the
underside of the joint
(Figure 3).
3. Holding the joint bolt in the top of
the joint with a 9/16” socket, use a
second 9/16” socket on the nut in
the bottom of the joint to adjust the
torque setting (Figure 3).
4. Replace cap and reassemble cable
manager.
Final Wiring Connections
1. Make final wiring connections to
appropriate monitor locations after
all components are installed.
Figure 1 - Adjust the Height-Adjusting Segment
plastic
shroud
Figure 2 - Adjust the Height-Adjusting Segment
3/”
16
Allen key
3/”
16
Allen key
front arm
segment back arm
segment joint
cap
cable
manager
Figure 3 - Adjust the Torque
joint
bolt

19
Monitor Arms
Assembly Instructions

1330 Bellevue Street • P.O. Box 8100 • Green Bay, WI 54308-8100 • Tel [phone] • www.ki.com
© 2021 Krueger International, Inc. All Rights Reserved • Code KI-AI-000012R2/KI/PDF/0821
Monitor Arms
Assembly Instructions