KidKraft ARBOR CREST DELUXE PLAYSET User manual

INSTALLATION AND OPERATING INSTRUCTIONS
ARBOR CREST DELUXE PLAYSET - F29205
Table of Contents
Warnings and Safe Play Instructions.....pg. 2
Instructions for Proper Maintenance .....pg. 4
About Our Wood – Limited Warranty.....pg. 5
Keys to Assembly Success. . . . . . . . . . . . pg. 6
Part ID ............................pg. 7
Step-By-Step Instructions ............pg. 14
Installation of ID/Warning Plaque ......pg. 76
WARNING
Rev 11/21/20199409205
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
[email protected]
[email protected]
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
KidKraft Netherlands BV
Olympisch Stadion 8
1076 DE Amsterdam
The Netherlands
[email protected]
[phone] M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/
FOR OUTDOOR FAMILY
DOMESTIC USE ONLY
4 - 8 Hrs
Two personTwo person
assemblyassembly
To reduce the risk of serious injury or death, you must read and follow
these instructions. Keep and refer to these instructions often and give
them to any future owner of this play system. Manufacturer contact
information provided below.
OBSTACLE FREE SAFETY ZONE - 30' 11-3/8″ x 25′ 9-5/16″ (9.433m x 7.856m) area requires Protective Surfacing. See
page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6’ 3-5/8” (1.92m)
CAPACITY - 9 Users Maximum, Ages 3to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
WARNING. Only for domestic use.
6'9 13/16"
207.8 cm
31'3 5/8"
954.3 cm
25'9 5/16"
785.6 cm
18' 3/16"
554.3 cm
[30' 11-3/8"]
943.29 cm
[17' 9-7/8"]
543.29 cm
[6' 8-7/16"]
204.29cm
[25' 9-5/16"]
785.6cm

2
Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 2m from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
,senilsehtolc,seporhtiwyalpotnerdlihcwollaREVEN•
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
stemlehtropsroekibraewotnerdlihcwollaREVEN•
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
D
Never add extra length to chain or rope. The chains or ropes
provided are the maximum length designed for the swinging
element(s).
O NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
WARNING
eeS.tes-yalpruoyfosnoitatimilyticapacevresbO
front cover.
gnisolcnetoofllufdnagnittfillewhtiwnerdlihcsserD
footwear.
retnecehtnithgiewllufriehthtiwtisotnerdlihchcaeT
of the swing seat to prevent erratic swing motion or
falling off.
,gnissim;doowdekcarcronekorb,deretnilpsrofkcehC
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
niahc,sreddalepor,seporgnibmilcdednepsustahtyfireV
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
rehtodnaedilsehtkcehc,syadtohrodnaynnusnO
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
raewtoofleehroeotneporaewotnerdlihcwollatonoD
like sandals, flip–flops or clogs.
dniheb,neewteb,tnorfni,klawotnerdlihcwollatonoD
or close to moving rides.
poolroseporrosniahcgniwstsiwtnerdlihcteltonoD
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
.noitomnierayehtelihwsedirffotegnerdlihcteltonoD
.tewsitinehwtnempiuqenognibmilctimreptonoD
anitnempiuqefoesuroyalphguortimreptonoD
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
.staesrosedirytpmegniwsotnerdlihcwollatonoD
rotsrfidaehedilsnwodogotnerdlihcwollatonoD
run up slide.
WARNING – Safe Play Instructions
Orientate slide such that it gets the least amount of exposure
to the sun.

3
One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet
high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch depth.
• Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this
should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface -- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-place surfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself” projects.
• Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of
Surfacing Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the
surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height - vertical
distance between a designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing
below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 2m from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar
from which the swing is suspended.
• For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all
directions.
From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls.
2H 2H
H
Denotes Use Zone with Protective Surfacing
Use Zone for Single-Axis Swings
6 ft.
6 ft.
6 ft.
6 ft.
Denotes Use Zone with Protective Surfacing
Use Zone for Multi-Axis Swings
6 ft. 6 ft.
6 ft.
L

4
Instructions for Proper Maintenance
HARDWARE:
Check metal parts for rust. If found,
sand and repaint using a non-lead
paint complying with 16 CFR 1303.
Inspect and tighten all hardware. On
wood assemblies DO NOT OVER-
TIGHTEN as to cause crushing and
splintering of wood.
Check for sharp edges or protruding screw threads, add
washers if required.
SHOCK ABSORBING SURFACING:
Check for foreign objects. Rake and check depth of loose
fill protective surfacing materials to prevent compaction
and maintain appropriate depth. Replace as necessary.
(See Protective Surfacing, page 3)
GROUND STAKES (ANCHORS):
Check for looseness, damage or deterioration. Should
firmly anchor unit to ground during use. Re-secure and
or replace, if necessary.
SWING HANGERS:
Check that bolts are secure and tight. Quick clips should
be completely closed and threaded clips screwed tight.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS, ROPES AND RIDES:
Reinstall if removed during cold season. Check all
moving parts including swing seats, ropes, chains and
attachments for wear, rust and other deterioration.
Replace as needed.
Check that ropes are tight, secure at both ends and
cannot loop back as to create an entrapment.
WOOD PARTS:
Check all wood members for deterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
Unprotected, they will appear weathered over time.
Periodic application of an exterior water repellent or stain
(water-based) will help improve appearance and life.
Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor
products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important
that you, the owner, properly maintain it.
Check the following at the beginning of the play season:
HARDWARE:
Inspect for tightness. Must be firmly against, but not
crushing the wood. DO NOT OVER-TIGHTEN.
This will cause splintering of wood.
Check for sharp edges or protruding screw threads.
Add washers if required.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check twice a month during play season:
SWING HANGERS:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS AND RIDES:
Check swing seats, all ropes, chains and attachments for
fraying, wear, excessive corrosion or damage.
Replace if structurally damaged or deteriorated.
Check once a month during play season:
SWINGS AND RIDES:
To prolong their life, remove swings and store inside
when outside temperature is below 32°F/0°C. Below
freezing, plastic parts may become more brittle.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check at the end of the play season:
If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable hazards
at the time it is discarded. Be sure to follow your local waste ordinances.
Use an extra
Flat Washer
If Bolt protrudes
beyond T-Nut

5
About Our Wood
KidKraft Premium Play Systems uses 100% FSC wood. Although we take great care in selecting the best quality lumber available,
wood is still a product of nature and susceptible to weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is
different than the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing tension which can
result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of
the product:
1. Checking is surface cracks in the wood along the grain. A post (4” x 4”) will experience more checking than a board (1” x 4”)
because the surface and interior moisture content will vary more widely than in thinner wood.
2. Warpingresults from any distortion (twisting, cupping) from the original plane of the board and often happens from rapid
wetting and drying of the wood.
3. Fading happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey over time.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption
during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, so we recommend applying a
water repellent or stain on a yearly basis (see your local stain and paint supplier for a recommended product).
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are
concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.
Complete and mail registration card to receive important product notifications and assure prompt
warranty service.
5Year Limited Warranty
KidKraft warrants that this product is free from defect in materials and workmanship for a period of one
year from the original date of purchase. In addition, lumber is warranted for 5years against structural
failure due to rot and insect damage. All other parts, such as hardware, swings, rides, accessories, and
slides carry a one-year warranty only.
This warranty applies to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your Play System. This warranty does not
cover any inspection cost.
This Limited Warranty does not cover:
• Labor for replacement of any defective item(s);
• Incidental or consequential damages;
• Cosmetic defects which do not affect performance or integrity;
• Vandalism; improper use or installation; acts of nature;
•Minor twisting, warping, checking, or any other natural occurring properties of wood that do not
affect performance or integrity.
KidKraft products have been designed for safety and quality. Any modifications made to the original
product could damage the structural integrity of the unit leading to failure and possible injury.
Kidkraft cannot assume any responsibility for modified products. Furthermore, modification voids
any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a
KidKraft Play System be used in public settings such as schools, churches, playgrounds, parks, day
cares and the like. Such use may lead to product failure and potential injury. Any and all public use
will void this warranty.
KidKraft disclaims all other representations and warranties of any kind, express or implied.
This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or
province to province. This warranty excludes all consequential damages, however, some states do not allow the
limitation or exclusion of consequential damages, and therefore this limitation may not apply to you.

6
Part Identication Key
On each page, you will nd the parts
and quantities required to complete
the assembly step illustrated on that
page. Here is a sample.
Key Number: The rst two digits
represent the step number. The third
digit represents the piece. Note that if
the part is used in multiple steps then
the number only reects the rst step
it is used in.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only a
at washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer rst then at washer
then hole. Because the assemblies
need to be squared do not completely
tighten until instructed. Pay close
attention to diameter of the bolts.
5/16” is slightly larger than 1/4”.
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed
threads. If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.
This identies information that requires
special attention. Improper assembly could
lead to an unsafe or dangerous condition.
Where this is shown, 2 or 3
people are required to safely
complete the step. To avoid
injury or damage to the
assembly make sure to
get help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to
assure proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8” & 3/16” Bit
Tighten
Bolts
No Yes
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• #1, #2 & #3 Phillips
or Robertson Bits
or Screwdriver
• Ratchet with extension
(1/2” & 9/16” sockets)
• Open End Wrench
(7/16”, 1/2” & 9/16”)
• Adjustable Wrench
• 1/8” & 3/16” Drill Bits
• Pencil
• 3/16” Hex Key
• 8’ Step Ladder
• Safety Glasses
• Adult Helpers
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
Use an extra
Flat W asher
If Bolt protrudes
beyond T-Nut
Lag Screw
Flat Washer
Lag Assembly
Before mounting Lag Screw,
use factory drilled holes as
guides to drill 1/8” pilot holes
Hex Bolt Bolt Assembly
T-Nut
(Hammer into place)
Do not crush wood!
Lock
Washer
Flat
Washer

7
1 x 3 x 37"
2x - 9590 - 25.4 x 76.2 x 939.8mm - 3839590
1 x 3 x 10-5/8"
6x - 9598 - 25.4 x 76.2 x 269.9mm - 3839598
5x - 9601 - 15.9 x 114.3 x 939.8mm - 3839601
5/8 x 4-1/2 x 37"
5/8 x 4-1/2 x 28-1/4"
1x - 9603 - 15.9 x 114.4 x 717.6mm - 3839603
2x - 9604 - 15.9 x 114.3 x 939.8mm - 3839604
5/8 x 4-1/2 x 37"
2x - 9607 - 31.8 x 88.9 x 292.1mm - 3839607
1-1/4 x 3-1/2 x 11-1/2"
1-1/4 x 3 x 10"
2x - 9609 - 31.8 x 76.2 x 254mm - 3839609
3x - 9612 - 15.9 x 82.6 x 660.4mm - 3839612
5/8 x 3-1/4 x 26"
1 x 3 x 37"
1x - 9613 - 25.4 x 76.2 x 939.8mm - 3839613
2x - 9614 - 25.4 x 76.2 x 914.4mm - 3839614
1 x 3 x 36"
1x - 9615 - 25.4 x 76.2 x 889mm - 3839615
1 x 3 x 35"
1 x 2 x 35"
1x - 9624 - 25.4 x 50.8 x 889mm - 3839624
1x - 9625 - 25.4 x 139.7 x 889mm - 3839625
1 x 5-1/2 x 35"
1x - 9599 -25.4 x 76.2 x 717.6mm - 3839599
1 x 3 x 28-1/4"
1x - 9605 - 15.9 x 114.3 x 717.6mm - 3839605
5/8 x 4-1/2 x 28-1/4"
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)

8
2x - 9629 - 25.4 x 76.2 x 882.7mm - 3839629
1 x 3 x 34-3/4"
1 x 3 x 34-3/4"
2x - 9630 - 25.4 x 76.2 x 882.7mm - 3839630
1x - 9632 - 25.4 x 76.2 x 679.5mm - 3839632
1 x 3 x 26-3/4"
1 x 3 x 8-1/4"
4x - 9631 - 25.4 x 76.2 x 209.6mm - 3839631
1x - 9633 - 25.4 x 76.2 x 679.5mm - 3839633
1 x 3 x 26-3/4"
1 x 3 x 26-3/4"
1x - 9634 - 25.4 x 76.2 x 679.5mm - 3839634
1x - 9635 - 25.4 x 76.2 x 679.5mm - 3839635
1 x 3 x 26-3/4"
5x - 9638 - 15.9 x 136.5 x 762mm - 3839638
5/8 x 5-3/8 x 30"
5/8 x 4-1/2 x 30"
1x - 9639 - 15.9 x 114.3 x 762mm - 3839639
1x -
9809
- 76.2 x 133.4 x 1219.2mm - 3839809
3 x 5-1/4 x 48"
1x -
9810
- 76.2 x 133.4 x 1219.2mm - 3839810
3 x 5-1/4 x 48"
1 x 3-1/4 x 38-21/32"
1x - 9642 - 25.4 x 82.6 x 982mm - 3839642
1x - 9643 - 76.2 x 76.2 x 1124mm - 3839643
3 x 3 x 44-1/4"
2 x 3 x 36-3/4"
2x - 9644 - 50.8 x 76.2 x 933.5mm - 3839644
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
4x

9
2x - 9645 - 50.8 x 76.2 x 1174.8mm - 3839645
2 x 3 x 46-1/4"
1 x 4 x 42-1/4"
2x -
9646
- 25.4 x 101.6 x 1073.2mm - 3839646
6x -
9647
- 31.8 x 76.2 x 419.1mm - 3839647
1-1/4 x 3 x 16-1/2"
1-1/4 x 3 x 15-9/16"
2x -
9648
- 31.8 x 76.2 x 395.2mm - 3839648
1x - 9655 - 25.4 x 76.2 x 863.6mm - 3839655
1 x 3 x 34"
2x - 9656 - 34.9 x 85.7 x 1092.2mm - 3839656
1-3/8 x 3-3/8 x 43"
2x - 9657 - 34.9 x 85.7 x 1092.2mm - 3839657
1-3/8 x 3-3/8 x 43"
2x - 9658 - 34.9 x 85.7 x 1181.1mm - 3839658
1-3/8 x 3-3/8 x 46-1/2"
1x - 9659 - 34.9 x 85.7 x 1181.1mm - 3839659
1-3/8 x 3-3/8 x 46-1/2"
1x - 9661 - 34.9 x 85.7 x 1181.1mm - 3839661
1-3/8 x 3-3/8 x 46-1/2"
2x - 9662 - 34.9 x 85.7 x 889mm - 3839662
1-3/8 x 3-3/8 x 35"
2x - 9663 - 25.4 x 76.2 x 406.4mm - 3839663
1 x 3 x 16"
1x - 9664 - 25.4 x 76.2 x 863.6mm - 3839664
1 x 3 x 34"
1x - 9665 - 25.4 x 76.2 x 863.6mm - 3839665
1 x 3 x 34"
6x - 9666 - 15.9 x 76.2 x 619.1mm - 3839666
5/8 x 3 x 24-3/8"
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)

10
14x -
9667
- 15.9 x 76.2 x 584.2mm - 3839667
5/8 x 3 x 23"
3x -
9668
- 25.4 x 76.2 x 863.6mm - 3839668
1 x 3 x 34"
2x -
9669
- 31.8 x 63.5 x 663mm - 3839669
1-1/4 x 2-1/2 x 26-7/64"
2x -
9670
- 31.8 x 63.5 x 663mm - 3839670
1-1/4 x 2-1/2 x 26-7/64"
1x -
9671
- 31.8 x 76.2 x 1098.6 - 3839671
1-1/4 x 3 x 43-1/4"
3x -
9672
- 31.8 x 76.2 x 254mm - 3839672
1-1/4 x 3 x 10"
1x -
9673
- 15.9 X 82.6 X 863.6mm - 3839673
5/8 x 3-1/4 x 34"
1x -
9674
- 15.9 x 82.6 x 863.6mm - 3839674
5/8 x 3-1/4 x 34"
1x -
9675
- 15.9 x 82.6 x 863.6mm - 3839675
5/8 x 3-1/4 x 34"
1x -
9676
- 25.4x 76.2 x 863.6mm - 3839676
1 x 3 x 34"
1x -
9677
- 15.9 x 107.3 x 939.8mm - 3839677
5/8 x 4-7/32 x 37"
2x -
9750
- 25.4 x 76.2 x 247.9mm - 3839750
1 x 3 x 9-3/4"
2x -
9748
- 34.9 x 76.2 x 177.8mm - 3839748
1-3/8 x 3 x 7"
Part Identification (Reduced Part Size)
3x -
9805
- 25.4 x 76.2 x 863.6mm - 3839805
1 x 3 x 34"

11
17 x S3 -
#8 x 2-1/2"
- 52043522
63.5mm
48 x S4 -
#8 x 3"
- 52043530
76.2mm
34 x S7
- #12 x 2"
- 52433620
50.8mm
16 x S5 - #8 x 1/2" - 52433502
12.7mm
171 x S20 -
#8 x 1-3/8"
- 52043516
34.9mm
34.9mm
18 x LW2 - 5/16" - 51303300
34 x LN2 - 5/16"
-
54303300
21 x
TN2
- 5/16"
-
54503300
69 x
TN1
- 1/4"
-
54503200
6.4mm
6.4mm
75 x LW1 - 1/4" - 51303200
91 x FW2 - 5/16" - 51103300
73 x FW1 - 1/4" - 51103200
22 x FW0 - 3/16" - 51103100
12 x S11
- #8 x 2"
- 52043520
50.8mm
6 x
- 5/16 x 2-1/2"
- 53453322
7.9 x 63.5mm
8 x WL5 -
1/4 x 2-1/2"
- 52613222
6.4 x 63.5mm
7.9mm
6.4mm
7.9mm
9.5mm
7.9mm
9.5mm
7.9mm
6.4mm
4.8mm
Hardware Identification (Actual Size)
12 x S6 -#12 x 1" - 52433610
25.4mm
32mm
28.5mm
16mm
25.4mm
6x S10 - #8 x 1"
- 52433510
4 x S37
- #7 x 5/8"
- 52433009
2x
S38
- #7 x 1-1/8"
- 52433014
6x PB2
PB9
- 1/4 x 1-1/4
"
- 53433212
6 x
BN1
- 1/4"
-
54803200
4x WL3 - 1/4 x 1-3/8"- 52613216
2 x LN3
-
3/8 "
- 54303800
4 x
FW10 - 3/8" - 51103800
8 x
S0
- #8 x 7/8" - 52933505
22.2mm
4 x
S15 - #8 x 1-3/4" - (52043513)

12
11 x G21 -
5/16 x 3-3/4"
- 53703333
7.9 x 95.2mm
4 x G1
- 5/16 x 1-1/2" - 53703312
7.9 x 38.1mm
12 x
G7 -
5/16 x 5-1/2"
- 53703352
7.9 x 139.7mm
2 x G17 -
3/8 x 6"
- 53703860
9.5 x 152.4mm
7.9 x 155.6mm
40 x H8 -
1/4 x 4-1/4"
- 53703241
6.4 x 108mm
8 x H7 -
1/4 x 5-1/2"
- 53703252
6.4 x 139.7mm
1 x H4 -
1/4 x 4"
- 53703240
6.4 x 101.6mm
22 x H10 -
1/4 x 2-1/4"
- 53703221
6.4 x 57.2mm
4 x WB2 -
5/16 x 1-3/8" - 53613316
7.9 x 25.4mm
11 x WB9 -
5/16 x 2-1/8"
- 53613324
7.9 x 54mm
4 x WB1 -
5/16 x 1" - 53613310
7.9 x 25.4mm
Hardware Identification
76.2mm
2 x H12 -
1/4 x 3"
- 53703230
1 x D4 - #2 x 2 - 9200014
1 x G13 - 5/16 x 6-1/8"- 53703364
2 x WB8 -
5/16 x 2-3/8"
- 53613326
7.9 x 60.3mm

13
1x
- 9200131
1x - 3502045
1x - 3206106 (6pk)
2x - 3200020 (4pk)
2x - 9320131
1x - 3320283 (6pk)
1x
- 9759110
1x - 3759110
1x - 9759111
1x - 3320255
1x - 3200189 (2Pk)
1x - 3200145 (2pk)
1x - 3200193 (4pk)
1x - 3200718 (7pk)
2x - 9320130
Part Identification (Reduced Part Size)
1x
- 3320355
1x - 9320374
2x - 9200191
1x - 3200191
1x - 3200143
1x - 9200144
1x - 9200143
1x
- 3320240
(2pk)
1x - 3209110 (2pk)
1x - 7310149-1
2x 9502020
4x 9502045

14
B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.
Key Number: The rst two digits represent the step
number. The third digit represents the piece. Note
that if the part is used in multiple steps then the
number only reects the rst step it is used in.
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
Step 1: Inventory Parts - Read This Before Starting Assembly
• Please refer to Page 6 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the key number stamped on the ends of the boards.
Organize the wood pieces by step, as per the key numbering system below.
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 5)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 6)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3)
MODEL NUMBER: F29205
TRACKING NUMBER (from ID Plaque):
C. Read the assembly manual completely, paying special attention to EN71 and
ASTM warnings; notes; and safety/maintenance information on pages 1 - 6.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton. The tracking number is
located on the KidKraft ID Plaque (9320374).
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
Europe Customer Service: [phone]
[email protected]
EU Online Parts Replacement: parts.kidkraft.eu
[email protected]
Online Parts Replacement: parts.kidkraft.com
To warranty your product: kidkraft.com/warranty/
Customer Service:
1(800) 933-0771 or [phone]

15
1 x 1 x 3 x 34” (25.4 x 76.2 x 863.6 mm)
2 x 1-3/8 x 3-3/8 x 43” (34.9 x 85.7 x 1092.2 mm)
2 x 1-3/8 x 3-3/8 x 43” (34.9 x 85.7 x 1092.2 mm)
1 x 1 x 3 x 34” (25.4 x 76.2 x 863.6 mm)
Step 2
Wood Parts Hardware
9655 9805
9656
9657
TN1
TN1
TN1
TN1
H8
H8 H8
H8
FW1
FW1
FW1
FW1
FW1
LW1
LW1
LW1
LW1
LW1
8 x 1/4 x 4-1/4” (108mm)
(FW1, LW1, TN1)
H8
Note hole orientation
AI-1
H8x8 (FW1 TN1 LW1)
9656
9657
9656
9657
FW1
FW1
LW1
LW1
FW1
LW1
9805
9655

16
Step 3
2 x 1 x 3 x 37” (25.4 x 76.2 x 939.8 mm)
Wood Parts Hardware
9590
H10
H10
H10
H10
4 x 1/4 x 2-1/4” (57.1mm) (FW1, LW1, TN1)
4 x #8 x 3” (76.2 mm)
4 x #8 x 2” (50.8 mm)
H10
S4
S11
S4
S4
S4
S4
S11
S11
S11
S11
9590
H10
S4
S11
TN1 FW1 LW1
TN1
TN1
TN1
TN1
A-2
H10x4 (FW1 TN1 LW1)
S4x4 S11x4
9590
9590

17
AI-3
H7x4(FW1 TN1 LW1)
Step 4
LW1
LW1
FW1
FW1
2 x 1 x 3 x 10-5/8” (25.4 x 76.2 x 269.9 mm)
2 x 1-3/8 x 3-3/8 x 46-1/2” (34.9 x 85.7 x 1181.1 mm)
1 x 1 x 3 x 34” (25.4 x 76.2 x 863.6 mm)
1 x 1 x 3 x 34” (25.4 x 76.2 x 863.6 mm)
Wood Parts Hardware
9598 9665
9658
9664
4 x 1/4 x 5-1/2” (139.7 mm) (FW1, LW1, TN1)
H7
9658
9658
9658
9665
9664
9598
H7
H8
H8
H7
TN1
TN1
TN1
TN1
9664
LW1
LW1
FW1
FW1
H7
H7
TN1
TN1
9665
9598
9598
9598
LW1
LW1
FW1
FW1
2 x 1/4 x 4-1/4” (108mm) (FW1, LW1, TN1)
H8

18
Step 5
1 x 1-3/8 x 3-3/8 x 46-1/2” (34.9 x 85.7 x 1181.1 mm)
1 x 1-3/8 x 3-3/8 x 46-1/2” (34.9 x 85.7 x 1181.1 mm)
Wood Parts Hardware
9659
9661
LW1
LW1
FW1
FW1
H8
H8
TN1
TN1
2 x 1/4 x 4-1/4” (108mm) (FW1, LW1, TN1)
H8
AI-4
H8x4 (FW1 TN1 LW1)
9659
9661

19
AI-5
S4x2
Step 6
1 x 1 x 3 x 37” (25.4 x 76.2 x 939.8 mm)
Wood Parts Hardware
9613 2 x #8 x 3” (76.2 mm)
S4
9613 S4
S4

20
Step 7
2 x 1-1/4 x 3 x 15-9/16” (31.8 x 76.2 x 395.2 mm)
Wood Parts Hardware
9648
AI-6
S4x4 WL5 x2(FW2)
AI-6
S4x4 WL5 x2(FW2)
FW2
FW2
WL5
WL5
S4
S4
S4
S4
2 x 1/4 x 2-1/2” (63.5 mm) (FW2)
4 x #8 x 3” (76.2 mm)
WL5
S4
9648
9648
AI-6
S4x4 WL5 x2(FW2)
Pre-drill each hole
using a 1/8” drill bit for WL5.
Pre-drill each hole
using a 1/8” drill bit for WL5.