KidKraft Grand Valley Retreat User manual

INSTALLATION AND OPERATING INSTRUCTIONS
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions often
and give them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 30’ 11” x 28’ area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 7’1” (2.16 m)
CAPACITY - 11 Users Maximum, Ages 3to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
Warning. Only for demestic use.
WARNING
9403175
Table of Contents
Warnings and Safe Play Instructions. . . . . . . . . . . . . . . pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance ...............pg. 4
About Our Wood – Limited Warranty ..............pg. 5
Keys to Assembly Success ......................pg. 6
Metric Conversion Sheets ..................... pg. 7,8
Part ID.......................................pg. 9
Installation of I.D./Warning Plaque ............Final Step
GRAND VALLEY RETREAT – F23175
Rev 07/01/2019
Two person
assembly
10-12 Hrs
FOR FORT & SWING
18'-11"
28'-0"
30'-11"
10'-3"
2 - 3 Hrs
FOR SLIDE
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
[email protected]
[email protected]
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
KidKraft Netherlands BV
Olympisch Stadion 29
1076DE Amsterdam
The Netherlands
[email protected]
[phone] M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/

Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 2m from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
,seni lsehtolc,seporht iwyalpotnerdl ihcwol laREVEN•
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
stemlehtropsroekibraewotnerdl ihcwol laREVEN•
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
DO NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
Never add extra length to chain or rope. The chains or ropes
provided are the maximum length designed for the swinging
element(s).
WARNING
eeS. t es-ya l pruoyf osno i t a t imi ly t i capacevresbO
front cover.
gn i so l cnet oo f l l u fdnagn i t t fil l ewh t iwne rd l i hcsse rD
footwear.
retnecehtnithgiewl lufr iehtht iwt isotnerdl ihchcaeT
of the swing seat to prevent erratic swing motion or
falling off.
, gn i ss im; doowdekcar cronekorb, de r e tn i l psrofkcehC
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
n i ahc, s r edda lepor, sepo rgn i bmi l cdednepsust ah ty f i r eV
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
r eh t odnaed i l seh tkcehc, syadt ohrodnaynnusnO
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
r aewt oo f l eehroeo tnepor aewo tne rd l i hcwo l l at onoD
like sandals, flip–flops or clogs.
dniheb,neewteb, tnorfni,klawotnerdl ihcwol latonoD
or close to moving rides.
poolroseporrosniahcgniwstsiwtnerdl ihcteltonoD
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
.noi tomnierayehtel ihwsedi rf fotegnerdl ihcteltonoD
. t ews i t inehwt nemp i uqenogn i bmi l ct imr ept onoD
an i t nemp i uqef oe sur oya l phguo rt imr ept onoD
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
.staesrosedi rytpmegniwsotnerdl ihcwol latonoD
rotsrfidaehed i l snwodogo tne rd l i hcwo l l at onoD
run up slide.
WARNING – Safe Play Instructions
Orientate slide such that it gets the least amount of exposure
to the sun.
2

One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet
high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch depth.
• Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this
should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface -- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-place surfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself” projects.
• Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of
Surfacing Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the
surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height - vertical
distance between a designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing
below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 2m from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar
from which the swing is suspended.
• For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all
directions.
From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls.
2H 2H
H
Denotes Use Zone with Protective Surfacing
Use Zone for Single-Axis Swings
6 ft.
6 ft.
6 ft.
6 ft.
Denotes Use Zone with Protective Surfacing
Use Zone for Multi-Axis Swings
6 ft. 6 ft.
6 ft.
L
3

Instructions for Proper Maintenance
HARDWARE:
Check metal parts for rust. If found,
sand and repaint using a non-lead
paint complying with 16 CFR 1303.
Inspect and tighten all hardware. On
wood assemblies DO NOT OVER-
TIGHTEN as to cause crushing and
splintering of wood.
Check for sharp edges or protruding screw threads, add
washers if required.
SHOCK ABSORBING SURFACING:
Check for foreign objects. Rake and check depth of loose
fill protective surfacing materials to prevent compaction
and maintain appropriate depth. Replace as necessary.
(See Protective Surfacing, page 3)
GROUND STAKES (ANCHORS):
Check for looseness, damage or deterioration. Should
firmly anchor unit to ground during use. Re-secure and
or replace, if necessary.
SWING HANGERS:
Check that bolts are secure and tight. Quick clips should
be completely closed and threaded clips screwed tight.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS, ROPES AND RIDES:
Reinstall if removed during cold season. Check all
moving parts including swing seats, ropes, chains and
attachments for wear, rust and other deterioration.
Replace as needed.
Check that ropes are tight, secure at both ends and
cannot loop back as to create an entrapment.
WOOD PARTS:
Check all wood members for deterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
Unprotected, they will appear weathered over time.
Periodic application of an exterior water repellent or stain
(water-based) will help improve appearance and life.
Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor
products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important
that you, the owner, properly maintain it.
Check the following at the beginning of the play season:
HARDWARE:
Inspect for tightness. Must be firmly against, but not
crushing the wood. DO NOT OVER-TIGHTEN.
This will cause splintering of wood.
Check for sharp edges or protruding screw threads.
Add washers if required.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check twice a month during play season:
SWING HANGERS:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS AND RIDES:
Check swing seats, all ropes, chains and attachments for
fraying, wear, excessive corrosion or damage.
Replace if structurally damaged or deteriorated.
Check once a month during play season:
SWINGS AND RIDES:
To prolong their life, remove swings and store inside
when outside temperature is below 32°F/0°C. Below
freezing, plastic parts may become more brittle.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check at the end of the play season:
If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable hazards
at the time it is discarded. Be sure to follow your local waste ordinances.
Use an extra
Flat Washer
If Bolt protrudes
beyond T-Nut
4

About Our Wood
KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we
take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible
to weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is
different than the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing tension which can
result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of
the product:
1. Checking is surface cracks in the wood along the grain. A post (4” x 4”)will experience more checking than a board (1” x 4”)
because the surface and interiormoisture content will vary more widely than in thinner wood.
2. Warping results from any distortion (twisting, cupping) from the original plane ofthe board and often happens from rapid
wettingand drying of the wood.
3. Fading happens as a natural change in the wood coloras it is exposed tosun-light and will turn a grey over time.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption
during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, so we recommend applying a
water repellent or stain on a yearly basis (see your local stain and paint supplier for a recommended product).
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are
concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.
Complete and mail registration card to receive important product notifications and assure prompt
warranty service.
5 Year Limited Warranty
KidKraft warrants that this product is free from defect in materials and workmanship for a period of one
year from the original date of purchase. In addition, lumber is warranted for 5 years against structural
failure due to rot and insect damage. All other parts, such as hardware, swings, rides, accessories, and
slides carry a one-year warranty only.
This warranty applies to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your Play System. This warranty does not
cover any inspection cost.
This Limited Warranty does not cover:
•Labor for replacement of any defective item(s);
•Incidental orconsequential damages;
•Cosmetic defects whichdo not affect performance or integrity;
•Vandalism; improper use or installation; acts of nature;
•Minortwisting, warping, checking,or any other natural occurring properties of wood that do not
affect performance or integrity.
KidKraft products have been designed for safety and quality. Any modifications made to the original
product could damage the structural integrity of the unit leading to failure and possible injury.
Kidkraft cannot assume any responsibility for modified products. Furthermore, modification voids
any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a
KidKraft Play System be used in public settings such as schools, churches, playgrounds, parks, day
cares and the like. Such use may lead to product failure and potential injury. Any and all public use
will void this warranty.
KidKraft disclaims all other representations and warranties of any kind, express or implied.
This Warranty gives you specific legal rights. You may have otherrights as well which vary from state to state or
province to province. This warranty excludes all consequential damages, however, some states do notallow the
limitation or exclusion ofconsequential damages, andtherefore this limitation may not apply to you.
5

 
Keys to Assembly Success
Part Identification Key
On each page, you will find the parts and
quantities required to complete the assembly
step illustrated on that page. Here is a sample.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” is slightly
larger than 1/4”.
Once the assembly is tightened, watch for exposed
threads. If a thread protrudes from the T-Nut, remove the
bolt and add washers to eliminate this condition. Extra
washers have been provided for this purpose.
This identifies information that requires special
attention. Improper assembly could lead to an
unsafe or dangerous condition.
Where this is shown, 2 or 3
people are required to safely
complete the step. To avoid
injury or damage to the
assembly make sure to get help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole before
fastening screw or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill
1/8” Bit
Tighten
Bolts
No Yes
CAUTION – Protrusion Hazard
Tools Required
6
Shovel Level #2 & #3 Phillips
or Robertson
Safety
Glasses
Drill (1/8”
3/16” Bit)
Measuring
Tape
Hammer Ratchet 1/2”,
7/16” & 9/16”
Square
Ruler
Step
Ladder
12342X Post 2 x 4 x 83”
123
6

1 inch = 25.4mm
KIDKRAFT DESIGN HARDWARE
For example:
BOLT LENGTH 4½ (4.5) inches long
114mm long
1 inch = 25.4mm
25.4mm
4.5 inches x
DIAMETER CONVERSION
LENGTH CONVERSION
=
BOLT DIAMETER 5/16 (0.31) inches 0.31 inches x 25.4mm = 8mm
For example:
HARDWARE LENGTH CHART
inches vs millimetres
6 152
5½ 140
5 127
4½ 114
4 102
3½ 89
3 76
2½ 64
2 51
1½ 38 1¼ 32
1-
1/8
29
1 25.4
7/8 22 3/4 19 1/2 12.7
1/4" (6mm) Flat Washer
1/4" (6mm) Lock Washer
1/4"(0.25) = 6mm Hex Bolt
1/4" (6mm) T-Nut
5/16"(.31) = 8mm Lag Screw
5/16" (8mm) Flat Washer
1/4"(0.25) = 6mm Lag Screw
1/4" (6mm) Flat Washer
5/16" (8mm) Flat Washer
5/16" (8mm) Lock Washer
5/16"(.31) = 8mm Hex Bolt
5/16" (8mm) T-Nut
3/8"(.38) = 9.5mm Lag Screw
3/8" (9.5mm) Flat Washer
7

1 x 2 1 x 4 1 x 5
1 x 6
1 x 3
1/2 x 4
5/4 x 6
5 1/2"
139.7
1"
25.4
11.1
.44
82.6
3 1/4"
4 x 4
3 1/2"
88.9
3 1/2"
88.9
4 1/2"
114.3
5/8"
15.9
15.9
5/8" 1 3/8"
34.9
2 x 6
5 3/8"
136.5
1 1/2"
38.1
15.9
5/8" 3 3/8"
85.7
60.3
2 3/8"
15.9
5/8"
1505mm
KIDKRAFT DESIGN WOOD PROFILES
LENGTH CONVERSION
For example:
1 inch = 25.4mm
BOARD LENGTH 59¼ (59.25) inches 59.25 inches x 25.4mm =
Dimensions in brackets [mm] represent millimetres.
5/4 x 4
3 1/2"
88.9
1"
25.4
5 3/8"
136.5
5/8"
15.9
2 x 4
3 3/8"
85.7
1 3/8"
34.9
5/4 x 5
4 1/2"
114.3
1"
25.4 2 x 3
2 1/2"
63.5
1 3/8"
34.9
5/4 x 3
63.5
2 1/2"
25.4
1"
2 x 2
1 1/2"
38.1
1 1/2"
38.1
8

Nominal Size Actual Size
5/8 x 3 19/32 x 3
1 x 4 5/8 x 3-1/4
1 x 5 5/8 x 4-1/4
1 x 6 5/8 x 5-1/4
4pc. -041 -5/8 x 3 x 15" - Window Shutter FSC - Box 1 - 4608778
1pc. -344 -1 x 5 x 33-7/8" - Crowsnest Gap FSC - Box 4 - 4638111
1pc. -153 -1 x 5 x 36" - Floor A FSC - Box 2 - 4638796
3pc. -151 -1 x 5 x 42-1/2" - Slidenest Floor A FSC - Box 2 - 4638795
3pc. -032 -1 x 6 x 20-1/2" - Rock Board A FSC - Box 2 - 4638822
3pc. -033 -1 x 6 x 20-1/2" - Rock Board B FSC
- Box 2 -
4638823
1pc. -023 -1 x 4 x 15" - Ladder Gap FSC - Box 2 - 4638828
1pc. -030 -1 x 4 x 20-1/2" - Board Access FSC - Box 2 - 4638826
4pc. -166 -1 x 4 x 26-1/2" - Wall Board FSC - Box 3 - 4638039
1pc. -345 -1 x 4 x 33-7/8" - Crowsnest Floor FSC - Box 4 - 4638108
2pc. -346 -1 x 5 x 33-7/8" - Crowsnest Floor FSC - Box 4 - 4638109
2pc. -034 -1 x 6 x 20-1/2" - Rock Board C FSC
- Box 2 -
4638824
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
4pc. -187 -1 x 4 x 8-1/2" - Side Gable FSC - Box 2 - 4638819
2pc. -186 -1 x 4 x 13-1/2" - Centre Gable FSC - Box 2 - 4638820
1pc. -031 -1 x 6 x 20-1/2" - Rock Bottom FSC
- Box 3 -
4638827
2pc. -035 -1 x 6 x 20-1/2" - Rock Board D FSC
- Box 2 -
4638825
9

Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
2pc. - 411-1 x 6 x 27-1/2" - Wall Board FSC - Box 3 - 4638881
1pc. - 410 -1 x 6 x 32" - Center Board FSC - Box 3 - 4638883
1pc. -014 -5/4 x 4 x 6-1/2"
- Bench Brace Top FSC
- Box 2 - 48039836
1pc. -025 -5/4 x 3 x 34-1/4" - Top Ladder FSC - Box 2 - 4638829
1pc. -510 -5/4 x 3 x 34-1/4" - SW Table Top FSC - Box 3 - 4638622
1pc. -112 -5/4 x 3 x 31-3/4" - SW Table Top FSC - Box 3 - 4638811
3pc. -150 -1 x 6 x 42½" - Slidenest Floor FSC - Box 2 - 4638794
1pc. -342 -5/4 x 4 x 25-1/2" - Crowsnest Short FSC - Box 4 - 4638115
2pc. -012 -5/4 x 4 x 16" - Bench Base Cafe FSC - Box 2 - 48039236
4pc. -022 -5/4 x 4 x 13-3/4" - Ladder Tread FSC - Box 2 - 4638517
2pc. -011 -5/4 x 4 x 11" - Bench Leg Cafe FSC - Box 2 - 48039936
2pc. -010 -5/4 x 4 x 7" - Bench End Support Cafe FSC
- Box 2 - 48039136
6pc. -152 -1 x 6 x 36" - Floor FSC - Box 2 - 4638797
Nominal Size Actual Size
1 x 6 5/8 x 5-1/4
5/4 x 3 15/16 x 2-1/4
2 x 3 1-1/4 x 2-1/4
5/4 x 4 15/16 x 3-1/4
2pc. -111 -2 x 3 x 42-1/4" - Diagonal FSC - Box 3 - 4638587
1pc. -180 -5/4 x 4 x 29" - Roof Support FSC - Box 4 - 4638806
10

Nominal Size Actual Size
5/4 x 4 15/16 x 3-1/4
5/ x 5 15/16 x 4-1/4
1pc. -190 -5/4 x 4 x 31" - Right Gable Angle FSC - Box 4 - 4638817
1pc. -181 -5/4 x 4 x 29" - Roof Support Left FSC - Box 4 - 4638807
1pc. -127 -5/4 x 4 x 65-1/2" - Front Top FSC - Box 3 - 4638798
1pc. -100 -5/4 x 4 x 65-1/2" - Back Top FSC - Box 3 - 4638799
1pc. -110 -5/4 x 4 x 82-5/8" - Ground SW FSC - Box 3 - 4638782
1pc. -123 -5/4 x 5 x 6-1/2" - SL Top Right FSC
- Box 2 -
4638788
1pc. -120 -5/4 x 5 x 9-3/4" - SL Top Left FSC
- Box 2 -
4638787
2pc. -122 -5/4 x 4 x 31-7/8" - Post FSC - Box 3 - 4638791
1pc. -331 -5/4 x 4 x 33-7/8" - Crowsnest Back FSC - Box 4 - 4638105
2pc. -341 -5/4 x 4 x 34¼" - Crowsnest Upright FSC - Box 3 - 4638118
1pc. -070 -5/4 x 4 x 64-1/4" - Front Ground FSC - Box 3 - 4638847
1pc. -072 -5/4 x 4 x 64-1/4" - Back Ground FSC - Box 3 - 4638848
1pc. -165 -5/4 x 5 x 12-1/8"
- Steering Wheel Dash FSC
- Box 2 - 4638609
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
1pc. -191 -5/4 x 4 x 31" - Left Gable Angle FSC - Box 4 - 4638818
2pc. -013 -5/4 x 4 x 31-7/16" - Bench Top Cafe FSC - Box 3
-
48034836
1pc. -125 -5/4 x 5 x 30-5/8" - SL Top FSC - Box 3 - 4638793
1pc. -401 -5/4 x 4 x 30-5/8" - Bottom Board FSC - Box 3 - 4638882
11

Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
2pc. -081 -2 x 3 x 3" - Table Gusset FSC - Box 2 - 4638805
1pc. -400 -2 x 4 x 26-1/4" - SL Support FSC - Box 3
-
4638168
4pc. -330 -5/4 x 6 x 18" - Crowsnest Side FSC
- Box 3 -
4638843
2pc. -185 -5/4 x 6 x 10" - Sunburst FSC
- Box 2 -
4638614
1pc. -074 -5/4 x 5 x 33-5/8" - SL Bottom FSC - Box 3 - 4638846
2pc. -347 -5/4 x 5 x 31" - Crowsnest Wall FSC - Box 2 - 4638119
1pc. -370 -5/4 x 5 x 36-1/4" - Middle Arch FSC - Box 3 - 4638800
1pc. -124 -2 x 4 x 5-1/4" - Short Floor Joist FSC
- Box 2 -
4638623
1pc. -182 -1-1/4 x 2-1/8 x 24-5/8" - Top Post Right FSC - Box 4 - 4638809
1pc. -183 -1-1/4 x 2-1/8 x 24-5/8" - Top Post Left FSC - Box 4 - 4638808
1pc. -082 -1-1/4 x 1-1/4 x 44-7/8" - SL Post FSC - Box 3 - 4638790
2pc. -200 -5/4 x 6 x 32-1/4" - Roof Spacer FSC - Box 4 - 4638777
1pc. -080 -5/4 x 5 x 35-1/2" - Table Top FSC - Box 3 - 4638801
Nominal Size Actual Size
5/4 x 5 1 x 4-1/2
5/4 x 6 1 x 5-1/2
2 x 3 1-3/8 x 2-1/2
2 x 4 1-3/8 x 3-3/8
4pc. -333 -2 x 4 x 14-5/16" - Crowsnest Joist FSC
- Box 2 -
4638113
2pc. -121 -2 x 4 x 5-1/4" - Short Joist FSC
- Box 2 -
4638789
1pc. -332 -2 x 4 x 33-7/8" - Crowsnest Front FSC - Box 4 - 4638110
1pc. -340 -2 x 4 x 33-7/8" - Crowsnest SL Top FSC - Box 2 - 4638117
1pc. -126 -2 x 4 x 28-3/4" - SL End FSC - Box 2 - 4638792
2pc. -348 -2 x 4 x 27-3/4" - Crowsnest Face FSC - Box 2
-
4638107
12

Nominal Size Actual Size
2 x 4 1-3/8 x 3-3/8
1-1/4 x 5 1-1/4 x 5
2 x 6 1-1/2 x 5-1/4
2-1/2 x 3 2-1/2 x 3
4 x 4 3 x 3
3 x 5-1/4 3 x 5-1/4
1pc. -020 -2 x 4 x 62-7/8" - Left Access Rail FSC - Box 3 - 4638145
1pc. -192 -2 x 4 x 34-1/2" - Gable Bottom FSC - Box 3 - 4638816
1pc. -271 -2-1/2 x 3 x 15" - Block SW FSC
- Box 3 -
4638507
1pc. -270 -2-1/2 x 3 x 15" - SW Block Angle FSC - Box 3 - 4638508
1pc. -280 -2-1/2 x 3 x 64" - Support Cross FSC - Box 4 - 4638510
1pc. -260 -3 x 5-1/4 x 110" - Engineered SW Beam FSC - Box 2 - 4638509
1pc. -044 -4 x 4 x 38-1/2" - SW Wall FSC - Box 3 - 4638779
1pc. -073 -2 x 4 x 64-1/4" - Back Floor FSC - Box 3 - 4638849
1pc. -071 -2 x 4 x 64-1/4" - Front Floor FSC - Box 4 - 4638844
1pc. -085 -2 x 4 x 64-1/4" - Floor Joist FSC - Box 4 - 4638845
1pc. -184 -1-1/4 x 5 x 36" - SW Top FSC - Box 3 - 4638810
2pc. -334 -2 x 6 x 15" - Crowsnest Gusset FSC
- Box 2 -
4638112
2pc. -272 -4 x 4 x 105" - SW Post FSC - Box 3 - 4638166
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
1pc. -021 -2 x 4 x 62-7/8" - Right Access Rail FSC - Box 4 - 4638146
1pc. -024 -2 x 4 x 62-7/8" - Rock Rail FSC - Box 2 - 4638139
13

Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
1pc. -051 -1-1/4 x 30 x 54-1/8"
- SL Window Side Panel FSC
- Box 2 - 47638841
1pc. -043 -1-1/4 x 36 x 87-1/4"
- SW Side Panel FSC - Box 2 - 47638775
1pc. -223 -1-1/4 x 11-1/2 x 35-7/8"
- B Transom FSC
- Box 2 - 47638839
1pc. -222 -1-1/4 x 11-1/2 x 35-7/8"
- F Transom FSC
- Box 2 - 47638840
2pc. -050 -1-1/4 x 16-3/4 x 99"
- Narrow Window Panel FSC
- Box 3 - 47638837
2pc. -210 -1-1/4 x 31-3/4 x 41"
- Large Roof Panel FSC - Box 4 - 47638756
2pc. -211 -1-1/4 x 31-3/4 x 32-1/2"
- Small Roof Panel FSC - Box 4 - 47638760
1pc. -060 -1-1/4 x 38-1/2 x 57-3/8"
- SL Panel FSC - Box 4 - 47638842
1pc. -040 -1-1/4 x 35-1/2 x 99"
- Wall Cafe Window Panel FSC- Box 2 - 47638838
14

13pc. WB7 - Wafer Bolt 5/16 x 3" - (53613330)
3pc. WB2 - Wafer Bolt 5/16 x 1-3/8" - (53613316)
13pc. WB9 - WaferBolt 5/16 x 2-1/8" - (53613324)
6pc. H2 - Hex Bolt 1/4 x 2" - (53703220)
5pc. LS9 - Lag Screw 5/16 x 4-3/4" - (52213343)
5pc. WL3 - Wafer Lag 1/4 x 1-3/8" - (52613216)
17pc. WL5 - Wafer Lag 1/4 x 2-1/2"
- (52613222)
17pc. G8 - Hex Bolt 5/16 x 2"
- (53703320)
Hardware Identification (Actual Size)
7pc. WB8 - Wafer Bolt 5/16 x 2-3/8" - (53613326)
2pc. G1 - Hex Bolt 5/16 x 1-1/2" - (53703312)
12pc. G13 - Hex Bolt 5/16 x 6-1/8" - (53703364)
4pc. G17 - Hex Bolt 3/8 x 6" - (53703860)
1pc. G20 - Hex Bolt 3/8 x 4" - (53703840)
1pc. G18 - Hex Bolt 3/8 x 9" - (53703890) 1pc. G26 - Hex Bolt 3/8 x 9-1/4" - (53703891)
4pc. G21 - Hex Bolt 5/16 x 3-3/4" - (53703333)
15

4pc. WH2 -Wafer Head Screw #12 x 1" - (52613610)
7pc. LN3 -3/8 Lock Nut - (54303800)
12pc. TS - Trim Screw #6 x 30mm - (52953911)
22pc. S13 - Pan Screw #6 x 5/8" - (52413908)
14pc. FW10 - 3/8" Flat Washer - (51103800)
13pc. PB2 - Pan Bolt 1/4 x 1-1/4"
- (53432212) 4pc. S18 - Wood Screw #6 x 1" - (52013910)
89pc. PB1 - Pan Bolt 1/4 x 3/4"
- (9274203)
8pc. FW6 - #12 Screw Bezel - (9299500)
89pc. LN1 -1/4 Lock Nut - (9283200)
1pc. PB6 - Pan Bolt 1/4 x 1" - (9274210)
36pc. S8 - Pan Screw #12 x 3/4" - (52433603)
14pc. FW0 - 3/16" Flat Washer - (51103100)
14pc. FW1 - 1/4" Flat Washer - (51103200)
89pc. FW2 - 5/16" Flat Washer - (51103300)
18pc. LW1 - 1/4" Lock Washer - (51303200)
8pc. TN1 - 1/4" T - Nut -(54503200)
59pc. TN2 - 5/16" T- Nut - (54503300)
10pc. BN1 - 1/4" Barrel Nut - (54803200)
12pc. LN2 - 5/16" Lock Nut - (54303300)
23pc. LW2 - 5/16" Lock Washer - (51303300)
220pc. S20 - Wood Screw #8 x 1-3/8" - (52043516)
14pc. S10 - Pan Screw #8 x 1"
- (52433510)
92pc. S15 - Wood Screw #8 x 1-3/4" - (52043513)
15pc. S6 - Pan Screw #12 x 1"
- (9264610)
10pc. S7 - Pan Screw #12 x 2" - (52433620)
47pc. S4 - Wood Screw #8 x 3" - (52043530)
87pc. S3 - Wood Screw #8 x 2-1/2" - (52043522)
Hardware Identification (Actual Size)
16

1x - Quadrex Driver
(9200015)
2x - Steel Hand Grip
(9200211) -Yellow
2x - Swing Belt Seat
(9320130) Green
1x - Steering Wheel
(3320255)
2x -Flower Box
(9320401)
Green
1x - Plastic Formed
Washer (18 Pk)
(3290000)
2x - Acro Handle
(9320131) Green
1x -Flat Panel Bracket (2 Pk)
(3200636)
1x - Acro Bar
(9200130)
Green
1x - Rebar Ground
Stake (6 Pk)
(3200318)
1x - DX Swing Hangers
with Quick Links (6 Pk)
(3201950)
1x - Corner
Bracket (6 Pk)
(3206570)
1X - Corner Panel
Bracket (2 Pk)
(3200638)
1X - Corner Panel
Bracket (2 Pk)
(3200637)
3x - Narrow Angle
Bracket (2 Pk)
(3200639)
1x - #2 x 2"
Robertson Driver
(9200014)
1x - Heavy G-Bracket
(9200150)
2x - Heavy L-Bracket
(9200151)
1x -Telescope w/ Mount
(3320161)
- Shelbyville Deluxe Bracket Set
1x
(3201705)
1x - Heavy Bracket Set
(3200150) Green
1x - KidKraft
ID Plaque
(9320374)
Part Identification (Reduced Part Size)
1x - Rocks (10pk)
(3320210) -Green/Yellow/Burgundy
1x - EN71 Hand Rail
(9200223) -Yellow
1x - (3pk) Swing Bracket Set
(3201530) -Green
1x -TNR 2 Slide Lt Flange
(3310122) Green
1x -TNR 2 Slide Rt Flange
(3310123) Green
9x -TNR 2 Slide Elbow
(3310121) Green
1x - TNR 2 Slide Exit
(3310120) Green
1x - TNR 2 Slide Exit Top
(3310124) Green
1x -TNR 2 Post Mount
(9200203)
1x -TNR 2 Slide Support
(9200226)
1x - Heavy T-Bracket
(9200152)
1x - Welded Chain Bag (3200170) Green
4x 9201254
54" chain -Green
2x 9201225
25" chain -Green
1x - KidKraft Logo Plaque
(3320353)
10x - TNR 2 Clamp Ring
(9300120) (Green)
10pcs number 3300120
17

B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the Consumer Relations Department directly. Call us
before going back to the store.
STOP STOPSTOP STOP
First Step: Inventory Parts - Read This Before Starting Assembly
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information on pages 1 - 6.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton. The tracking number is
located on the KidKraft ID Plaque (9320374).
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
• Please refer to Page 6 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the three digit key number stamped on the ends of the
boards. The wood pieces are referenced throughout the instructions with this number.
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 5)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 6)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3)
MODEL NUMBER: F23175
TRACKING NUMBER (from ID Plaque):
[phone]
[email protected]
For online parts replacement visit
https://parts.kidkraft.eu/
1.800.933.0771 or 972.385.0100
[email protected]
[email protected]
For online parts replacement visit
https://parts.kidkraft.com/
18

19
2 x Bench End Support Cafe FSC 5/4 x 4 x 7”
2 x Bench Leg Cafe FSC 5/4 x 4 x 11”
2 x Bench Base Cafe FSC 5/4 x 4 x 16”
012
011
010
Fig. 1.1
Wood Parts Hardware
011
012
010
Flush
Step 1: Cafe Bench Assembly
Part 1
A: Flush to the top of (011) Bench Leg Cafe place (010) Bench End Support Cafe, angled corners facing down
and centred on the legs. Attach with 1 (H2) 1/4 x 2” Hex Bolt (with lock washer, at washer and t-nut). Make
sure the top of (010) Bench End Support Cafe is level then attach with 2 (S20) #8 x 1-3/8” Wood Screws as
shown in g. 1.1.
B: Flush to the outside edge of (011) Bench Leg Cafe attach (012) Bench Base Cafe with 2 (H2) 1/4 x 2” Hex
Bolts (with lock washer, at washer and t-nut) as shown in g. 1.1.
C: Repeat Steps A and B to create a second Bench Leg Assembly so it is opposite to the rst Bench Leg
Assembly. (g. 1.2)
1/4” Flat
Washer
1/4” Lock
Washer
1/4”
T-Nut
6 x 1/4 x 2” Hex Bolt (1/4” lock washer, 1/4” at washer, 1/4” t-nut)
4 x #8 x 1-3/8” Wood Screw
H2
H2
Flush H2
Note hole
location
H2
Flush
Flush
010
1/4”
T-Nut
012
Fig. 1.2
1/4” Flat
Washer
1/4” Lock
Washer
S20
S20
S20
011

20
Hardware
013
Wood Parts
Step 1: Cafe Bench Assembly
Part 2
2 x Bench Top Cafe FSC 5 x 4 x 31-7/16”
1 x Bench Brace Top FSC 5 x 4 x 6-1/2”
014
12 x #8 x 1-3/4” Wood Screw
Fig. 1.3
010
S15 x 12
Flush
013
010 014
1/2” gap minimum both ends
D: Place 2 (013) Bench Top Cafes on both Bench Leg Assemblies so the ends on each side hang over by 1”.
Outside edges of each (013) Bench Top Cafe to be ush to outside edge of each (010) Bench End Support Cafe.
Attach each (013) Bench Top Cafe to each (010) Bench End Support Cafe with 4 (S15) #8 x 1-3/4” Wood Screws
per board. Note: leave a gap of 1/2” minimum between boards on both ends. (g. 1.3 and 1.4)
E: Pre-drill with a 1/8” drill bit then attach, centred over the pilot holes of the (013) Bench Top Cafes place (014)
Bench Brace Top underneath the boards. Attach with 4 (S15) #8 x 1-3/4” Wood Screws. (g. 1.3 and 1.4)
Fig. 1.4 013
Side View
S15
011
010
S15
1”