KidKraft CASTLEWOOD User manual

INSTALLATION AND OPERATING INSTRUCTIONS
CASTLEWOOD- F25890
To reduce the risk of serious injury or death, you must
read and follow these instructions. Keep and refer to
these instructions often and give them to any future owner of this play system. Manufacturer contact
information provided below.
OBSTACLE FREE SAFETY ZONE - 28’’8” (8.7m) x 27’ (8.2m) area requires Protective Surfacing. See
Owner’s Manual.
MAXIMUM VERTICAL FALL HEIGHT - 6’9”(2.06m)
CAPACITY - 10 Users Maximum, Ages 3to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day
cares or parks.
Warning. Only for domesc use.
2-4 Hrs
Two person
assembly
TUBE SLIDE
WARNING
27’-0”
[8.2M]
28’-8” [8.7M]
Obstacle Free Safety Zone
28’ 8” [8.7M] x 27’ [8.2M]
-
SPEY
10-14 Hrs
TWO PERSON
ASSEMBLY
FORT
Rev 09/15/2020
Table of Contents
Warnings and Safe Play Instructions. . . . . . . . . . pg. 2
Protective Surfacing Guidelines...............pg. 3
Instructions for Proper Maintenance .........pg. 4
About Our Wood – Limited Warranty.........pg. 5
Keys to Assembly Success ....................pg. 7
Metric Conversion Sheets ....................pg. 8
Part ID .......................................pg. 10
Installation of I.D./Warning Plaque ..........pg. 89
Fort Guides ..................................pg. 90
9405890
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
[email protected]
[email protected]
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
KidKraft Netherlands BV
Olympisch Stadion 8
1076 DE Amsterdam
The Netherlands
[email protected]
[phone] M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/

2
Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 2m from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
,senilsehtolc,seporhtiwyalpotnerdlihcwollaREVEN•
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
stemlehtropsroekibraewotnerdlihcwollaREVEN•
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose- ll
surfacing materials washing away during heavy rains.
D
Never add extra length to chain or rope. The chains or ropes
provided are the maximum length designed for the swinging
element(s).
O NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
WARNING
eeS.tes-yalpruoyfosnoitatimilyticapacevresbO
front cover.
gnisolcnetoofllufdnagnittllewhtiwnerdlihcsserD
footwear.
retnecehtnithgiewllufriehthtiwtisotnerdlihchcaeT
of the swing seat to prevent erratic swing motion or
falling off.
,gnissim;doowdekcarcronekorb,deretnilpsrofkcehC
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
niahc,sreddalepor,seporgnibmilcdednepsustahtyfireV
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
rehtodnaedilsehtkcehc,syadtohrodnaynnusnO
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
raewtoofleehroeotneporaewotnerdlihcwollatonoD
like sandals, ip– ops or clogs.
dniheb,neewteb,tnorfni,klawotnerdlihcwollatonoD
or close to moving rides.
poolroseporrosniahcgniwstsiwtnerdlihcteltonoD
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
.noitomnierayehtelihwsedirffotegnerdlihcteltonoD
.tewsitinehwtnempiuqenognibmilctimreptonoD
anitnempiuqefoesuroyalphguortimreptonoD
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
.staesrosedirytpmegniwsotnerdlihcwollatonoD
rotsrdaehedilsnwodogotnerdlihcwollatonoD
run up slide.
WARNING – Safe Play Instructions
Orientate slide such that it gets the least amount of exposure
to the sun.

3
One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• M
aintain a minimum depth of 9 inches (23 cm) of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet (2,45 m) high; and 9 inches (23 cm) of sand or pea gravel for equipment up to 5 feet (1,5 m)
high. NOTE: An initial fill level of 12 inches (31 cm) will compress to about a 9-inch (23 cm) depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch (23 cm) depth.
• U
se a minimum of 6 inches (16 cm) of protective surfacing for play equipment less than 4 feet (1,22 m) in height. If maintained properly, this
should be adequate. (At depths less than 6 inches (16 cm), the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface-- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fillsurfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-placesurfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself ” projects.
• Review surfacespecifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of Surfacing
Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the surfaceis intended
to protect against serious head injury. This height should be equal to or greater than the fall height - vertical distance between a
designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 6 feet (1,8 m) from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top
bar from which the swing is suspended.
• F
or tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet (1,8 m) in all directions.
Protective Surfacing-Reducing Risk of Serious Head Injury From Falls
From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf
Denotes Use Zone with Protective Surfacing
Denotes Use Zone with Protective Surfacing
6 ft.
6 ft.
6 ft. (1,8m)
6 ft. (1,8m)
(1,8m)
6 ft.
(1,8m)
(1,8m)
6 ft.
(1,8m)
6 ft.
(1,8m)
Use Zone for Multi-Axis SwingsUse Zone for Single-Axis Swings

4
Instructions for Proper Maintenance
sand and repaint using a non-lead paint
splinteringof wood.
Check for sharp edges or protrudingscrew threads, add
washers if required.
fill protective surfacing materials to prevent compaction and
Check for looseness, damage ordeterioration. Should firmly
if necessary.
Check that bolts are secure and tight. Quick clips should be
completely closed and threaded clips screwed tight.
parts including swingseats, ropes, chains and attachments
Check that ropes are tight, secure at both ends and cannot
loop back as to create an entrapment.
Check all wood members fordeterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
basis is important maintenance to maintain maximum life
and performance oftheproduct.
Check the following at the beginning of the play season:
This will causesplinteringof wood.
Check for sharp edges orprotrudingscrew threads.
Add washers ifrequired.
materials to prevent compaction and maintain appropriate
Check twice a month during play season:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
Check swingseats, all ropes, chains and attachments for
fraying, wear, excessive corrosion ordamage.
Check once a month during play season:
To prolongtheir life, remove swings and store insidewhen
plasticparts may become morebrittle.
materials to prevent compaction and maintain appropriate
Check at the end of the play season:
If you disposeof your play set:
hazards at thetime it is discarded. Besure to follow yourlocal wasteordinances.
beyond T-Nut
flat washer
Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with
all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your
Play Set, it is important that you, the owner, properly maintain it.

5
About Our Wood
KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your
children’s use. Although we take great care in selecting the best quality lumber available, wood is still a
product of nature and susceptible to weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood
at the surface is different than the interior of the wood. As the climate changes, moisture moves in or out
of the wood, causing tension which can result in checking and or warping. You can expect the following
due to weathering. These changes will not affect the strength of the product:
1. Checking is surface cracks in the wood along the grain. A post (4” x 4”) will experience more checking
than a board (1” x 4”) because the surface and interior moisture content will vary more widely than in
thinner wood.
2. Warping results from any distortion (twisting, cupping) from the original plane of the board and often
happens from rapid wetting and drying of the wood.
3. Fading happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey
over time.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount
of water absorption during rain or snow thus decreasing the tension in the wood. Sunlight will break down
the coating, so we recommend applying a water repellent or stain on a yearly basis (see your local stain
and paint supplier for a recommended product).
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your
child. However if you are concerned that a part has experienced a severe weathering problem please call
our consumer relations department for further assistance.
Complete and mail registration card to receive important product notifications and assure prompt
warranty service.

6
KidKraft Limited Warranty
MISSING OR DAMAGED PARTS:
KidKraft will replace any parts within 90 days from date of purchase found to be missing from or
damaged in the original packaging. See Fig.1
Fig. 1 Product Age (All Parts) Consumer Pays
0-90 Days from date of purchase $0 for Part + Free Shipping
DEFECTS IN MATERIAL AND WORKMANSHIP:
KidKraft warrants that this product is free from defects in materials and workmanship for a period of one
(1) year from the original date of purchase (dated sales receipt and/or product registration is required).
This one (1) year warranty covers all parts including wood, hardware, and all accessories (Such as
swings, rides, and slides). See Fig. 2
Fig. 2 Product Age (All Parts) Consumer Pays
91 Days to 1 Year $0 for Part + Free Shipping
WOOD ROT, DECAY, AND INSECT DAMAGE:
All wood carries a five (5) year warranty against rot, decay, and insect damage (dated sales receipt
and/or product registration is required). Refer tothe schedule below for charges associated with
replacement of wood parts under this Limited Warranty. See Fig. 3
Fig. 3 Product Age (Wood Parts) Consumer Pays
0 Days to 1 Year $0 for Part + Free Shipping
After 1 Year to 5 Year $0 for Part + Shipping & Handling
Over 5 Years 100% for Part (if available) + Shipping & Handling
This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance
is required to ensure the integrity of this product. Failure by the owner to maintain the product according
to the maintenance requirements may void this warranty.
This Limited Warranty does NOT cover:
• Any inspection cost
• Labor and/or costs for replacement of any defective item(s), including but not limited to,
professional installer costs
• Incidental or consequential damages, including but not limited to, as a result of set relocation,
move and/or reinstall
• Cosmetic defects which do not affect performance or integrity of a part or the entire product
• Vandalism, improper use or installation, or acts of nature, including but not limited to, high winds,
fire, and flood
• Minor twisting, warping, checking, or any natural occurring properties of wood that do not affect
performance or integrity.
• Any KidKraft product purchased, including but not limited to, a non-approved retailer, auction
houses, second-hand, and as-is clearance items.
KidKraft products have been designed for safety and quality. Modifications made to the original product
may damage the structural integrity of the unit leading to failure and possible injury. KidKraft cannot
assume any responsibility for the modified products. Furthermore, modifications void all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a KidKraft
product be used in public settings such as schools, churches, playgrounds, parks, home and
professional day cares and the like. Such use may lead to product failure and potential injury. Public use
will void this warranty. KidKraft disclaims all other representations and warranties of any kind, express or
implied.

7
This identifies information that requires special
attention. Improper assembly could lead to an unsafe
or dangerous condition.
Where this is shown, 2 or 3 people
are required to safely complete the
step. To avoid injury or damage
to the assembly make sure to get
help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Part Identification Key
On each page, you will find the parts
and quantities required to complete the
assembly step illustrated on that page.
Here is a sample.
Key Number: The first two digits
represent the step number. The third
digit represents the piece. Note that if
the part is used in multiple steps then
the number only reflects the first step it
is used in.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” is slightly
larger than 1/4”.
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed threads.
If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8”& 3/16” Bit
Tighten
Bolts
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
No Yes
Lag Assembly
Bolt Assembly
Flat Washer
Lag Screw
Hex Bolt
Lock
Washer
Flat
Washer
Before mounting Lag
Screw, use factory drilled
holes as guides to drill 1/8”
pilot holes
T-Nut
(Hammer into place)
Do not crush wood!
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer
• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• Rubber Mallet
• #1 Phillips, #2 Robertson
and Screwdriver
• Ratchet with extension
(1/2” & 9/16” sockets)
• Open End Wrench
(1/2” & 9/16”)
• Adjustable Wrench
• 1/8” & 3/16” Drill Bits
• 3/16” Hex Key
• 8’ Step Ladder
• Safety Glasses
• Adult Helpers
• Pencil

8
1 inch = 25.4mm
SOLO)WAVE DESIGN HARDWARE
For example:
BOLT LENGTH 4½ (4.5) inches long
114mm long
1 inch = 25.4mm
25.4mm
4.5 inches x
DIAMETER CONVERSION
LENGTH CONVERSION
=
BOLT DIAMETER 5/16 (0.31) inches 0.31 inches x 25.4mm = 8mm
For example:
HARDWARE LENGTH CHART
inches vs millimetres
6 152
5½ 140
5 127
4½ 114
4 102
3½ 89
3 76
2½ 64
2 51
1½ 38 1¼ 32
1-1/8 29
1 25.4
7/8 22 3/4 19 1/2 12.7
1/4" (6mm) Flat Washer
1/4" (6mm) Lock Washer
1/4"(0.25) = 6mm Hex Bolt
1/4" (6mm) T-Nut
5/16"(.31) = 8mm Lag Screw
5/16" (8mm) Flat Washer
1/4"(0.25) = 6mm Lag Screw
1/4" (6mm) Flat Washer
5/16" (8mm) Flat Washer
5/16" (8mm) Lock Washer
5/16"(.31) = 8mm Hex Bolt
5/16" (8mm) T-Nut
3/8"(.38) = 9.5mm Lag Screw
3/8" (9.5mm) Flat Washer
KIDKRAFT HARDWARE

9
1 x 2 1 x 4 1 x 5
1 x 6
1 x 3
1/2 x 4
5/4 x 6
5 1/2"
139.7
1"
25.4
11.1
.44
82.6
3 1/4"
4 x 4
3 1/2"
88.9
3 1/2"
88.9
4 1/2"
114.3
5/8"
15.9
15.9
5/8" 1 3/8"
34.9
2 x 6
5 3/8"
136.5
1 1/2"
38.1
15.9
5/8" 3 3/8"
85.7
60.3
2 3/8"
15.9
5/8"
1505mm
SOLO)WAVE DESIGN WOOD PROFILES
LENGTH CONVERSION
For example:
1 inch = 25.4mm
BOARD LENGTH 59¼ (59.25) inches 59.25 inches x 25.4mm =
Dimensions in brackets [mm] represent millimetres.
5/4 x 4
3 1/2"
88.9
1"
25.4
5 3/8"
136.5
5/8"
15.9
2 x 4
3 3/8"
85.7
1 3/8"
34.9
5/4 x 5
4 1/2"
114.3
1"
25.4 2 x 3
2 1/2"
63.5
1 3/8"
34.9
5/4 x 3
63.5
2 1/2"
25.4
1"
2 x 2
1 1/2"
38.1
1 1/2"
38.1
KIDKRAFT WOOD PROFILE

10
1x - Base Clock
(9320124)
1x - Clock Subset
(3320329)
1x - Rebar Ground
Stake (6 Pk) (3200318)
1x - Beam Brkt.Set (3200143)
1x - Rocks (5pk)
(3320386)
1x - Swing Hanger (6 Pk)
(3206106)
1x - Beam L Brkt.
(3200145) (2pk)
2x - Acro Handle
(9320131) Green
1x - Acro Bar
(9200130)
Green
2x 9201225
25" chain -Green
2x - Swing Belt Seat
(9320130) Green
1x - Quick Link
with Thread (6 Pk)
(3206020)
1x - Clicker Phone
(3320252)
1x - Deep Sink,
Faucet, Knobs
1x - Deluxe Kitchen Set (3320969)
1x - Deluxe Stove Assembly
1x - Chimney Wall
(9320606)
1x - Welded Chain Bag (3200170) Green
1x - Jamb Mount
(4 Pk) (3206302)
1x - Utensil Shelf
1x - 3 Pane Modular Transon Window (2pk)
(3320538)
(2) 2756
Siding Assembly 1¼ x 19-15/16 x 39-3/16"
(32 x 506 x 995mm) 37632756
1x - Mailbox
(3320107)
4x 9201254
54" chain -Green
1x - KidKraft
ID Plaque
(9320374)
Part Identification (Reduced Part Size) -Box 1 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
1x - Cedar Summit
Plaque
(9320358)

11
(1) 2602 - 1-1/4 x 3 x 35-15/16" Upper Jamb 3632602
(1) 2601 - 1-1/4 x 3 x 41-15/16" Lower Jamb 3632601
(1) 0475 - 15/16 x 4-1/4 x 6-1/4" - Chimney Top 38047567
Part Identification - Box 1
(2) 2717 - 3/4 x 1-3/4 x 9-3/4" Clock Block
3632717
(4) 0457 - 1 x 2 x 8-1/4" - Counter Joist 38045736
(1) 2687 - Counter Back 1 x 4 40-5/8" 3632687
(2) 0461 - 1 x 2 x 12-9/16" - Counter Brace 38046136
(1) 2685 - Counter Top 1 x 4 x 40-5/8" 3632685
(1) 2686 - Counter Front 5/8 x 2-3/4 x 40-5/8" 3632686
(2) 2716 - Counter Mid Top 1 x 4 x 17-5/8" 3632716
(1) 2720
Lower Window Insert 1.27 x 18.8 x 41.91"
37632720
(2) 0455 - Counter Side 5/8 x 2 x 6-3/4" 38045536
(1) 649A Short Half Wall
1.27 x 18.8 x 20-15/16" (32 x 477 x 532mm)
37632649A
(2) 2719
Upper Window Insert 1.27 x 18.8 x 35.86"
(32 x 478 x 911mm) 37632719 (1) 2665 Half Wall Insert 1.4 x 20-1/4 x 38.8"
(35 x 514 x 985mm) 37632665
ID#1 - F25890 06-06-2016

12
- (53703320)
4pc. G8 - Hex Bolt 5/16 x 2"
(8 x 51mm)
Hardware - Box 1 (Actual Size)
48" High Rail Slide -7310248
(8 x 25mm)
- (53703340)
3pc. G4 - Hex Bolt 5/16 x 4"
(8 x 102mm)
- (53703352)
14pc. G7 - Hex Bolt 5/16 x 5-1/2"
(8 x 140mm)
- (53703223)
4pc. H11 - Hex Bolt 1/4 x 2-3/4"
(6 x 70mm)
- (53703221)
4pc. H10 - Hex Bolt 1/4 x 2-1/4"
(6 x 57mm)
- (52613222)
16pc. WL5 - Wafer Lag 1/4 x 2-1/2"
(6 x 64mm)
- (53703333)
7pc. G21 - Hex Bolt 5/16 x 3-3/4"
(8 x 95mm)
3pc. WB7 - Wafer Bolt 5/16 x 3" (8 x 76mm) - (53613330)
- (52213230)
2pc. LS3 - Lag Screw 1/4 x 3"
(6 x 76mm)
2pc. WB1 - Wafer Bolt 5/16 x 1" - (53613310)
- (53703211)
24pc. H9 - Hex Bolt 1/4 x 1-1/4"
(6 x 32mm)

13
37pc. LW1 - 1/4"(6mm) Lock Washer -
(51303200)
56pc. FW2 - 5/16" (8mm) Flat
Washer - (51103300)
50pc. FW1 - 1/4"(6mm) Flat Washer -
(51103200)
Hardware - Box 1 (Actual Size)
- (52043522)
12pc. S3 - Wood Screw #8 x 2-1/2"
- (52043530)
4pc. S4 - Wood Screw #8 x 3"
9pc. S7 - Pan Screw #12 x 2" - (52433620)
2pc. S6 - Pan Screw #12 x 1"
(52433610)
8pc. S10 - Pan Screw #8 x 1"
(52433510)
5pc. PB2 -
Pan Bolt 1/4 x 1-1/4" (53433212)
62pc. S5 - Pan Screw #8 x 1/2" - (52433502)
20pc. TS - Trim Screw #6 x 30mm - (52953911)
- (52043520)
4pc. S11 - Wood Screw #8 x 2"
5pc. FW0 - 3/16" (5mm) Flat Washer -
(51103100)
70pc. S0 - Truss Screw #8 x 7/8" - (52933505)
23pc. LN2 - 5/16"(8mm) Lock Nut
(54303300)
10pc. TN2 - 5/16" (8mm) T- Nut
(54503300)
5pc. LW2 - 5/16" (8mm) Lock Washer -
(51303300)
5pc. BN1 - 1/4" (6mm) Barrel Nut
(54803200)
32pc. TN1 - 1/4" (6mm) T - Nut
(54503200)
1pc. D4 - 2 x 2 Robertson Driver Bit (9200014)
- (52043517)
56pc. S30 - Wood Screw #8 x 1-1/16"
- (52043516)
90pc. S20 - Wood Screw #8 x 1-3/8"
16pc. S8 - Pan Screw #12 x 3/4"
(52433603)
4pc. S18 - Wood Screw #6 x 1" - (52013910)
10pc. S13 - Pan Screw #6 x 5/8" - (52413908)
ID#1 - F25890 06-06-2016
-
-
16 79

14
2pc. -2774 - Upright 1¼ x 3 x 42" (32 x 76 x 1067mm) 3632774
1pc. -2630 - SW Top 1¼ x 5½ x 42" (32 x 140 x 1067mm) 39632630
2pc. -2768 - Panel Floor 1¼ x 3 x 42"
(32 x 76 x 1067mm) 3632768
5pc. -2769 - Panel BT Frame 1¼ x 3 x 42" (32 x 76 x 1067mm)
3632769
2pc. -2613 - 2 x 3 x 86-11/16" (51 x 76 x 2202mm) - Heavy SW Post 3632613
3pc. -2770 - End Post Left 1¼ x 2½ x 87" (32 x 64 x 2210mm) 3632770
3pc. -2771 - End Post 1¼ x 2½ x 87" (32 x 64 x 2210mm) 3632771
1pc. -2616 - 5/4 x 4 x 46-1/2" (25 x 89 x 1181mm) SW Support 3632616
2pc. -2607 - 1-1/4 x 3 x 22" (32 x 76 x 559mm) - Diagonal 3632607
2pc. -2778 - 5/4 x 4 x 14¼" (25 x 89 x 362)
SW Ground MOD 3632778
2pc. -2777 - 2 x 2 x 40-1/4" (38 x 38 x 1022mm) - Side Joist MOD 3632777
2pc. -2780 - 1 x 6 x 19" (16 x 137 x 483mm)
RK Board A 3632780
3pc. -2781 - 1 x 6 x 19" (16 x 137 x 483mm)
RK Board B 3632781
2pc. -2779 - 1 x 6 x 19"(16 x 137 x 483mm )
Access Board 3632779
1pc. -2758
RT Post Assembly
1¼ x 2½ x 87"
(32 x 64 x 2210mm )
37632758
1pc. -2757
LT Post Assembly
1¼ x 2½ x 87"
(32 x 64 x 2210mm )
37632757
1pc. -2608 - 1-1/4 x 3 x 40-3/4" (32 x 76 x 1035mm) - Floor Joist 3632608
1pc. -2648 - 1 x 4 x 40-5/8 (16 x 86 x 1032mm )- Floor Board 3632648
8pc. -2609 - 1 x 5 x 40-5/8"(16 x 114 x 1032mm ) - Floor Board 3632609
2pc. 2775 Panel Cross Support 1¼ x 3 x 42"
(32 x 76 x 1067mm) 3632775
Part Identification - Box 2
1pc. -2614 - 4 x 6 x 88" - (76 x 133 x 2235mm) Engineered Beam3632614
1pc. -2615 - 4 x 4 x 50-15/16" - (76 x 76 x 1294mm) SW Upright 3632615
2pc. -2776 - Rock Rail 1¼ x 2½ x 51" (32 x 64 x 1295mm) 3632776
2pc. -2772 - Panel Floor Support 1¼ x 3 x 42" (32 x 76 x 1067mm)
3632772
ID#2 - F25890 06-06-2016

15
Part Identification - Box 3
(1) 2718
Door Window Panel
1¼ x 15¾ x 40¾
37602718B
(1) -2601 -1-1/4 x 3 x 41-15/16" Lower Jamb 3632601
(1) Narrow Angle Bracket (3 Pk)
(3200640)
(4) 2759 Roof End 1-1/4 x 3 x 10" (32 x 76 x 254mm) 3632759
(1) 2752 -MOD Roof Front 1¼ x 20-7/16 x 44"
37632752
(2) 2751 -MOD Roof Bottom 1-3/16 x 16 25/32 x 44"
37632751
(1) 2753 -MOD Roof Back 1¼ x 20-13/64 x 44"
37632753
(4) H3 - Hex Bolt 1/4 x 2-1/2" - 53703222
(23) S0 - Truss Screw #8 x 7/8" - 52933505
(2) 2761 -Roof Sleeper C ¾ x 2 x 35" (19 x 51 x 889mm ) 3632761
(2) Jamb Mount (9206300)
(1) 2720
Lower Window Insert 1.27 x 18.8 x 41.91"
37632720
(2) Peak Detail
(3330121)
(1) 2715 -5/4 x 3 x 10" - Door Stop
3632715
- 52043522(8) S3 - Wood Screw #8 x 2-1/2"
- 52043520(27) S11 - Wood Screw #8 x 2"
- 52043516(8) S20 - Wood Screw #8 x 1-3/8" 1x Magnetic Catch
1x Catch Plate
(2) S4 - Wood Screw #8 x 3" - 52043530
9207713
Door Catch
Door Hinge
2x 9201712
2x 9201711
Door Handle
1x - Door Hardware (3201710)
(4) S18 - Wood Screw #6 x 1" - 52013910
(16) S13 - Pan Screw #6 x 5/8" - 52413908
(4) 2 60 Roof Support 1¼ x 2¼ x 37½" 3632760
ID#2 - F25890 06-06-2016

16
1x- TNR3 Extend Flange Lt
(3310230)
1x - MOD Side Lite
(9320516)
Part Identification (Reduced Part Size)
(1) Rebar Ground Stake
(9290318)
1x - TNR3 Short Exit
(3310232)
9x - TNR 2 Slide Elbow
(3310221)
1x - TNR3 Post Mount
(9203602)
1x - TNR 3 Tube Support
(9203601)
1x- TNR3 Extend Flange Rt
(3310231)
1x - TNR 2 Slide Clamp Ring
(10 pk) (9300220)
1x - TNR 2 Slide Exit Top
(3310224)
ID#2 - F25890 06-06-2016

17
18 - Truss Screw #8 x 7/8"
(#8 x 22mm)
(52933505)
- Quadrex
Driver Bit (9200015)
- Hex Bolt1/4 x 4¼" (6 x108mm)- (53703241)
(1) Wafer Lag Screw 1/4 x 2-1/2"
(6 x 64mm) (52613222)
- Wood Screw#8 x 3"(#8 x 76mm) (52043530)
19 - Pan Screw#12 x 1"
(#12 x 25mm)
(52433610)
- 1/4" (6mm) T - Nut
(54503200)
- 1/4" (6mm) Lock Washer
(51303200)
- 1/4" (6mm) Flat Washer (51103200)
- Pan Bolt1/4 x 1" (6 x 25mm)
(53413210)
94 -1/4" (6mm) Lock Nut
(54303200)
- #12 Screw Bezel - (9299500)
- Pan Bolt1/4 x 1-1/4" (6 x 32mm)
(53433212)
- Wood Screw#8 x 2" (#8 x 51mm)(52043520)
- Pan Bolt1/4 x 3/4" (6 x 19mm)
(53453203)
- Pan Screw#12 x 2"
(#12 x 51mm) (52433620)
ID#2 - F25890 06-06-2016

18
B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
First Step: Inventory Parts - Read This Before Starting Assembly
• Please refer to Page 7 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the key number stamped on the ends of the boards.
Organize the wood pieces by step, as per the key numbering system below.
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 5)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 6)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3)
MODEL NUMBER: F25890
TRACKING NUMBER (from ID Plaque):
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information on pages 1 - 7.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton.The tracking number is
located on the KidKraft ID Plaque (9320374).
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
[phone]
[email protected]
For online parts replacement visit
https://parts.kidkraft.eu/
1.800.933.0771 or 972.385.0100
[email protected]
[email protected]
For online parts replacement visit
https://parts.kidkraft.com/

19
It is important to assemble the frame on a at, smooth surface.
A: Place (2771) End Post and (2770) End Post Left side by side with the grooves facing up and in. Put (2770)
End Post Left on the right hand side. Place (2775) Panel Cross Support in the top grooves, (2772) Panel Floor
Support in the middle grooves and (2769) Panel BT Frame in the bottom grooves. (g. 1.1).
B: Make sure assembly is square then attach with 4 (S30) Wood Screws per board. (g. 1.1)
C: Tap 3 (TN1) T-nuts in (2775) Panel Cross Support and (2772) Panel Floor Support and 2 in (2769) Panel BT
Frame. (g. 1.1 and 1.2)
24 x Wood Screw
16 x T-nut
2 x End Post
2 x End Post Left
2 x Panel Cross Support
2 x Panel Floor Support
2 x Panel BT Frame
S30
2775
Wood Parts Hardware
2772
2771
2770
2769
Fig. 1.2
Fig. 1.1
Bottom
Top
2772
2775
2770
2771
2769
S30
S30
x 3
x 3
x 2
x 4 x 4 per
board
Flush
Flush
Step 1: Front and Back Wall Prep
Part 1
TN1
TN1
TN1
TN1
TN1

20
It is important to assemble the frame on a at, smooth surface.
D: Turn the assembly over, place (2774) Upright in the middle groves of (2775) Panel Cross Support and (2772)
Panel Floor Support then attach all boards with 8 (H9) Hex Bolts (with lock washer and at washer) connecting to
the previously installed t-nuts. (g. 1.3 and 1.4)
E: Repeat steps A-D for a second assembly.
16 x Hex Bolt
 (lockwasher&atwasher)
2 x Upright
H9
Wood Parts Hardware
2774
Fig. 1.4
Fig. 1.3
2772
Flush
2775
2774
H9
H9
H9
H9
x 3
x 3
x 2
Step 1: Front and Back Wall Prep
Part 2
2770
2771
FW1
LW1