KidKraft NEWPORT PLAYSET F29015 User manual

INSTALLATION AND OPERATING INSTRUCTIONS
NEWPORT PLAYSET – F29015
Table of Contents
Warnings and Safe Play Instructions..........pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance .........pg. 4
About Our Wood – Limited Warranty.........pg. 5
Keys to Assembly Success ....................pg. 7
Part ID .......................................pg. 8
Step-By-Step Instructions ...................pg. 14
Installation of ID/Warning Plaque...........pg. 55
To reduce the risk of serious injury or death, you must read and
follow these instrucons. Keep and refer to these instrucons
oen and give them to any future owner of this play set.
Manufacturer contact informaon provided below.
OBSTACLE FREE SAFETY ZONE - 25’1“ x 26’ area requires Protecve Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6’ (1.8 m)
CAPACITY - 9 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.RESIDENTIAL HOME USE
ONLY. Not intended for public areas such as mul-unit residences, schools, churches, nurseries, day cares or
parks.
WARNING
Rev 06/11/20189409015
10'2"
13'1"
25'1"
26'0"
Spring Meadow
Swing Set
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
[email protected]
[email protected]
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
KidKraft Netherlands BV
Olympisch Stadion 29
1076DE Amsterdam
The Netherlands
[email protected]
[phone] M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/
2-4 Hrs
10 - 12 Hrs
FOR FORT & SWING
TWO PERSON
ASSEMBLY
10 - 12 Hrs
FOR FORT & SWING
4 - 8 Hrs

Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED.Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of seriousor fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervisionis requiredfor children of all ages.
eeS.tes-yalpruoyfosnoitatimilyticapacevresbO
front cover.
gnisolcnetoofllufdnagnittfillewhtiwnerdlihcsserD
footwear.
retnecehtnithgiewllufriehthtiwtisotnerdlihchcaeT
of the swing seat to preventerratic swing motion or
falling off.
,gnissim;doowdekcarcronekorb,deretnilpsrofkcehC
loose, or sharp edged hardware. Replace, tighten andor
sand smooth as required prior to playing.
niahc,sreddalepor,seporgnibmilcdednepsustahtyfireV
or cable are secured at both ends and cannot be looped
back on itselfas to create an entanglement hazard.
rehtodnaedilsehtkcehc,syadtohrodnaynnusnO
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with waterand wipe
dry prior to using.
raewtoofleehroeotneporaewotnerdlihcwollatonoD
like sandals, flip–flops or clogs.
dniheb,neewteb,tnorfni,klawotnerdlihcwollatonoD
or close to moving rides.
poolroseporrosniahcgniwstsiwtnerdlihcteltonoD
them over the top support bar. This may reduce the
strength of the chain or rope andcause premature failure.
.noitomnierayehtelihwsedirffotegnerdlihcteltonoD
.tewsitinehwtnempiuqenognibmilctimreptonoD
anitnempiuqefoesuroyalphguortimreptonoD
manner for which it was notintended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
.staesrosedirytpmegniwsotnerdlihcwollatonoD
rotsrfidaehedilsnwodogotnerdlihcwollatonoD
run up slide.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 2m from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
,senilsehtolc,seporhtiwyalpotnerdlihcwollaREVEN•
pet leashes, cables, chains or cord-like items when using
this play-set or toattach these items to play-set.
ponchos, hoods, scarves,capes,necklaces, items with
draw-strings, cords orties when using this play-set.
stemlehtropsroekibraewotnerdlihcwollaREVEN•
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps,increases the risk of serious injury and death to
children from entanglementand strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play settipping over and loose-fill
surfacing materials washing away during heavy rains.
DO NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
WARNING
WARNING – Safe Play Instructions
Orientate slide such that it gets the least amount of exposure
to the sun.
2 [email protected]

One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet
high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch depth.
• Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this
should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface -- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-place surfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself” projects.
• Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of Surfacing
Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the surface is intended
to protect against serious head injury. This height should be equal to or greater than the fall height - vertical distance between a
designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 2m from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar
from which the swing is suspended.
• For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all
directions.
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls
From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf
Denotes Use Zone with Protective Surfacing
Denotes Use Zone with Protective Surfacing
6 ft.
6 ft. 6 ft.
6 ft.
6 ft. 6 ft.
6 ft.
Use Zone for Multi-Axis SwingsUse Zone for Single-Axis Swings
3 [email protected]

Instructions for Proper Maintenance
HARDWARE:
Check metal parts for rust. If found,
sand and repaint using a non-lead
paint complying with 16 CFR 1303.
Inspect and tighten all hardware. On
wood assemblies DO NOT OVER-
TIGHTEN as to cause crushing and
splintering of wood.
Check for sharp edges or protruding screw threads, add
washers if required.
SHOCK ABSORBING SURFACING:
Check for foreign objects. Rake and check depth of loose
fill protective surfacing materials to prevent compaction
and maintain appropriate depth. Replace as necessary.
(See Protective Surfacing, page 3)
GROUND STAKES (ANCHORS):
Check for looseness, damage or deterioration. Should
firmly anchor unit to ground during use. Re-secure and
or replace, if necessary.
SWING HANGERS:
Check that bolts are secure and tight. Quick clips should
be completely closed and threaded clips screwed tight.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS, ROPES AND RIDES:
Reinstall if removed during cold season. Check all
moving parts including swing seats, ropes, chains and
attachments for wear, rust and other deterioration.
Replace as needed.
Check that ropes are tight, secure at both ends and
cannot loop back as to create an entrapment.
WOOD PARTS:
Check all wood members for deterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
Unprotected, they will appear weathered over time.
Periodic application of an exterior water repellent or stain
(water-based) will help improve appearance and life.
Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor
products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important
that you, the owner, properly maintain it.
Check the following at the beginning of the play season:
HARDWARE:
Inspect for tightness. Must be firmly against, but not
crushing the wood. DO NOT OVER-TIGHTEN.
This will cause splintering of wood.
Check for sharp edges or protruding screw threads.
Add washers if required.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check twice a month during play season:
SWING HANGERS:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS AND RIDES:
Check swing seats, all ropes, chains and attachments for
fraying, wear, excessive corrosion or damage.
Replace if structurally damaged or deteriorated.
Check once a month during play season:
SWINGS AND RIDES:
To prolong their life, remove swings and store inside
when outside temperature is below 32°F/0°C. Below
freezing, plastic parts may become more brittle.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check at the end of the play season:
If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable hazards
at the time it is discarded. Be sure to follow your local waste ordinances.
Use an extra
Flat Washer
If Bolt protrudes
beyond T-Nut
4 [email protected]

About Our Wood
KidKraft Premium Play Systems uses 100% FSC wood. Although we take great care in selecting the best quality lumber available,
wood is still a product of nature and susceptible to weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is
different than the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing tension which can
result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of
the product:
1. Checking is surface cracks in the wood along the grain. A post (4” x 4”) will experience more checking than a board (1” x 4”)
because the surface and interior moisture content will vary more widely than in thinner wood.
2. Warping results from any distortion (twisting, cupping) from the original plane of the board and often happens from rapid
wetting and drying of the wood.
3. Fading happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey over time.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption
during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, so we recommend applying a
water repellent or stain on a yearly basis (see your local stain and paint supplier for a recommended product).
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are
concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.
Complete and mail registration card to receive important product notifications and assure prompt
warranty service.
5Year Limited Warranty
KidKraft warrants that this product is free from defect in materials and workmanship for a period of one
year from the original date of purchase. In addition, lumber is warranted for 5years against structural
failure due to rot and insect damage. All other parts, such as hardware, swings, rides, accessories, and
slides carry a one-year warranty only.
This warranty applies to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your Play System. This warranty does not
cover any inspection cost.
This Limited Warranty does not cover:
• Labor for replacement of any defective item(s);
• Incidental or consequential damages;
• Cosmetic defects which do not affect performance or integrity;
• Vandalism; improper use or installation; acts of nature;
•Minor twisting, warping, checking, or any other natural occurring properties of wood that do not
affect performance or integrity.
KidKraft products have been designed for safety and quality. Any modifications made to the original
product could damage the structural integrity of the unit leading to failure and possible injury.
Kidkraft cannot assume any responsibility for modified products. Furthermore, modification voids
any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a
KidKraft Play System be used in public settings such as schools, churches, playgrounds, parks, day
cares and the like. Such use may lead to product failure and potential injury. Any and all public use
will void this warranty.
KidKraft disclaims all other representations and warranties of any kind, express or implied.
This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or
province to province. This warranty excludes all consequential damages, however, some states do not allow the
limitation or exclusion of consequential damages, and therefore this limitation may not apply to you.
5 [email protected]

This identifies information that requires special
attention. Improper assembly could lead to an unsafe
or dangerous condition.
Where this is shown, 2 or 3 people
are required to safely complete the
step. To avoid injury or damage
to the assembly make sure to get
help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Part Identification Key
On each page, you will find the parts
and quantities required to complete the
assembly step illustrated on that page.
Here is a sample.
Key Number: The first two digits
represent the step number. The third
digit represents the piece. Note that if
the part is used in multiple steps then
the number only reflects the first step it
is used in.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” is slightly
larger than 1/4”.
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed threads.
If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8” & 3/16” Bit
Tighten
Bolts
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• #1 Phillips, #2 Robertson
and Screwdriver
• Ratchet with extension
(1/2” & 9/16” sockets)
• Open End Wrench
(1/2” & 9/16”)
• Adjustable Wrench
• 1/8” & 3/16” Drill Bits
• 3/16” Hex Key
• 8’ Step Ladder
• Safety Glasses
• Adult Helpers
• Pencil
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
No Yes
Lag Assembly
Bolt Assembly
Flat Washer
Lag Screw
Hex Bolt
Lock
Washer
Flat
Washer
Before mounting Lag
Screw, use factory drilled
holes as guides to drill 1/8”
pilot holes
T-Nut
(Hammer into place)
Do not crush wood!
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer
6 [email protected]

1 inch = 25.4mm
KIDKRAFT DESIGN HARDWARE
For example:
BOLT LENGTH 4½ (4.5) inches long
114mm long
1 inch = 25.4mm
25.4mm
4.5 inches x
DIAMETER CONVERSION
LENGTH CONVERSION
=
BOLT DIAMETER 5/16 (0.31) inches 0.31 inches x 25.4mm = 8mm
For example:
HARDWARE LENGTH CHART
inches vs millimetres
6 152
5½ 140
5 127
4½ 114
4 102
3½ 89
3 76
2½ 64
2 51
1½ 38 1¼ 32
1-1/8 29
1 25.4
7/8 22 3/4 19 1/2 12.7
1/4" (6mm) Flat Washer
1/4" (6mm) Lock Washer
1/4"(0.25) = 6mm Hex Bolt
1/4" (6mm) T-Nut
5/16"(.31) = 8mm Lag Screw
5/16" (8mm) Flat Washer
1/4"(0.25) = 6mm Lag Screw
1/4" (6mm) Flat Washer
5/16" (8mm) Flat Washer
5/16" (8mm) Lock Washer
5/16"(.31) = 8mm Hex Bolt
5/16" (8mm) T-Nut
3/8"(.38) = 9.5mm Lag Screw
3/8" (9.5mm) Flat Washer
7 [email protected]

3pc. - 1777
CE Rock Board B (1 x 6 x 17") - Box 1 - 3561777
1pc. - 1779 CE Access Board (1 x 6 x 17")
- Box 1 - 3561779
2pc. - 1778 CE Rock Board A (1 x 6 x 17")
- Box 1 - 3561778
2pc. - 1927 Top Front Back (1 x 4 x 56-3/4") - Box 1 - 3641927
1pc. - 1922
Seat Rail (1 x 4 x 27") - Box 1 - 3131922
1pc. - 1923
Side Top (1 x 4 x 26-7/8") - Box 1 - 3131923
1pc. - 1918 Roof End (1 x 4 x 36-5/8") - Box 1 - 3641918
1pc. - 1925
Sw Top (1 x 4 x 36") - Box 1 - 3131925
1pc. - 1928
Lower Side (1 x 5 x 59-11/16") - Box 1 - 3131928
1pc. - 1917
Lower Back (1 x 5 x 56-7/8") - Box 1 - 3131917
2pc. - 0304
CE Floor Board (1 x 4 x 32-1/2") - Box 1 - 3130304
1pc. - 1914
Cafe Ground (1 x 5 x 41-1/2") - Box 1 - 3131914
1pc. - 1915 Chalk Wall Spacer (1 x 2 x 29-1/2") - Box 1 - 3641915
2pc. - 1911
Table Top (1 x 5 x 28-7/8") - Box 1 - 3561911
1pc. - 1920
Seat Bottom (1 x 5 x 17-3/4") - Box 1 - 3131920
1pc. - 1981
Top Side (1 x 4 x 36") - Box 1 - 3131981
3pc. - 1982
Wall Board (5/8 x 3 x 19") - Box 1 - 3131982
2pc. - 1980
Top Front Back (1 x 4 x 38-1/2") - Box 1 - 3131980
2pc. - 1920 $PRPVIEW:{Description}$PRPVIEW:{Desc} ($PRPVIEW:{Imp}$PRPVIEW:{Imperial}) - Box 1 - $PRPVIEW:{PN}$PRPVIEW:{PartNo}
Part Identification (Reduced Part Size)
Nominal Size
1" x 2"
1" x 4"
1" x 5"
1" x 6"
Actual Size
⅝" x 1⅜"
⅝" x 3⅜"
⅝" x 4½"
⅝" x 5⅜"
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
8 [email protected]

5pc. - 1776
Floor Board (1 x 6 x 23-1/2") - Box 1 - 3131776
1pc. - 1760
Floor (1 x 6 x 26-7/8") - Box 1 - 3131760
5pc. - 0318
Ground Stake (1-1/4 x 1-1/2 x 14") - Box 1 - 3650318
2pc. - 1766
1pc. - 1912
1pc. - 1924
SW Floor (1 x 6 x 26-7/8") - Box 1 - 3131924
1pc. - 1913
Back Floor (1 x 6 x 38-3/4") - Box 1 - 3131913
1pc. - 1767
Lower Front (1 x 6 x 39-3/4") - Box 1 - 3131767
2pc. - 1774
CE Gap Board (1 x 6 x 23-1/2") - Box 1 - 3131774
1pc. - 1910
Seat (1 x 6 x 28-7/8") - Box 1 - 3561910
1pc. - 1862
SW Support (5/4 x 4 x 46-1/2") - Box 1 - 3131862
1pc. - 1763
Floor Joist (5/4 x 2 x 38-1/2") - Box 1 - 3131763
1pc. - 1919
Roof Ridge (2 x 2 x 37-7/8") - Box 1 - 3131919
1pc. -
1761
Side Joist (2 x 2 x 34-3/4") - Box 1 - 3131761
1pc. - 1990
Back Divider (2 x 2 x 59-3/8") - Box 1 - 3131912
Corner Block (2 x 3 x 4-1/2") - Box 1 - 3131766
Chalk Wall Brace (1 x 2 x 38-1/2") - Box 1 - 3131990
2pc. - 1920 $PRPVIEW:{Description}$PRPVIEW:{Desc} ($PRPVIEW:{Imp}$PRPVIEW:{Imperial}) - Box 1 - $PRPVIEW:{PN}$PRPVIEW:{PartNo}
Part Identification (Reduced Part Size)
Nominal Size
1" x 6"
5/4" x 4"
2" x 2"
2" x 3"
Actual Size
⅝" x 5⅜"
1" x 3¼"
1½" x 1½"
1⅜" x 2½"
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
9 [email protected]

4pc. - 1500
Post (2 x 4 x 83") - Box 1 - 3131500
1pc. - 1826
Front Beam (2 x 6 x 83-5/8") - Box 1 - 3131826
1pc. - 1856
SW Upright (2 x 4 x 48-5/16") - Box 1 - 3131856
2pc. - 1863
SW Post (2 x 4 x 86-11/16") - Box 1 - 3131863
1pc. - 1825
Back Beam (2 x 6 x 83-5/8") - Box 1 - 3131825
1pc. - 4919
SW Rail Block (2 x 4 x 5-3/8") - Box 1 - 3134919
2pc. - 1926
Table Support (2 x 6 x 12-5/16") - Box 1 - 3131926
1pc. - 1916
Front Divider (2 x 4 x 59-1/4") - Box 1 - 3131916
2pc. - 0349
Rock Rail (2 x 3 x 51") - Box 1 - 3560349
2pc. - 1921
Seat Post (2 x 4 x 11") - Box 1 - 3131921
1pc. - 1764
Floor Front (2 x 3 x 38-1/2") - Box 1 - 3131764
1pc. - 0369
Lower Diagonal (2 x 3 x 37") - Box 1 - 3130369
1pc. - 0312
Gusset (2 x 3 x 16") - Box 1 - 3130312
1pc. - 1861
Sw Mount (2 x 4 x 38-1/8") - Box 1 - 3131861
Part Identification (Reduced Part Size)
Nominal Size
2" x 4"
2" x 6"
Actual Size
1⅜" x 3⅜"
1½" x 5⅜"
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
10 [email protected]

1pc. H8 -
Hex Bolt 1/4 x 4-1/4"
- (9277241)
4pc. H7 -
Hex Bolt 1/4 x 5-1/2"
- (9277252)
3pc. H4 -
Hex Bolt 1/4 x 4"
- (9277240)
8pc. LS1 - Lag Screw
1/4 x 1-1/2"
- (9262212)
9pc. LS3 - Lag Screw
1/4 x 3"
- (9262230)
27pc. H2 -
Hex Bolt 1/4 x 2"
- (9277220)
3pc. H6 -
Hex Bolt 1/4 x 4-3/4"
- (9277243)
4pc. G1 -
Hex Bolt 5/16 x 1-1/2"
- (9277312)
2pc. G8 -
Hex Bolt 5/16 x 2"
- (9277320)
4pc. G4 -
Hex Bolt 5/16 x 4"
- (9277340)
5pc. G5 -
Hex Bolt 5/16 x 4-1/2"
- (9277342)
2pc. LS2 - Lag Screw
1/4 x 2-1/2"
- (9272222)
Hardware Identification (Actual Size)
11 [email protected]

11pc. S3 - Wood Screw #8 x 2-1/2" - (52042522)
10pc. S4 - Wood Screw #8 x 3" - (52042530)
22pc. S7 - Pan Screw
#12 x 2"
- (9264620)
2pc. S6 - Pan Screw
#12 x 1"
- (52433610)
4pc. S15 - Wood Screw #8 x 1-3/4" - (52042513)
7pc. S10 - Pan Screw
#8 x 1"
- (9264510)
45pc. S5 - Pan Screw
#8 x 1/2"
- (9264504)
22pc. S1 - Wood Screw #8 x 1-1/8" - (52042514)
83pc. S2 - Wood Screw #8 x 1-1/2" - (52042512)
306pc. S0 - Truss Screw
#8 x 7/8"
- (9229505)
5pc. PB2 - Pan Bolt
1/4 x 1-1/4"
- (9274211)
13pc. LW2 - 5/16" Lock Washer - (9253300)
2pc. LN2 - 5/16" Lock Nut
-
(9283300)
13pc. TN2 - 5/16" T- Nut
-
(9285300)
5pc.
BN1 - 1/4" Barrel Nut
-
(9248200)
38pc. TN1 - 1/4" T - Nut
-
(9285200)
43pc. LW1 - 1/4" Lock Washer - (9253200)
17pc. FW2 - 5/16" Flat Washer - (9251300)
55pc. FW1 - 1/4" Flat Washer - (9251200)
1pc. - PB5 -Pan Bolt
1/4 x 2
- (9274220)
2pc. MB1 -Pan Bolt
#12 x 1/2"
- (53433602)
2pc. LN4 -
#12 Lock Nut
- (9289600)
2pc. S8 - Pan Screw
#12 x 3/4"
- (53433602)
1pc. PB6 - Pan Bolt
1/4 x 1"
- (9274210)
8pc. FW6 - #12 Screw Bezel - (9299500)
89pc. PB1 - Pan Bolt
1/4 x 3/4"
- (9274203)
35pc. FW3 - #8 Flat Washer - (9251500)
24pc. FW0 - 3/16" Flat Washer - (9251100)
Hardware Identification (Actual Size)
12 [email protected]

7310248
Yellow
é
é
9320370
Part Identication (Reduced Part Size)
13 [email protected]

B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.
STOP STOPSTOP STOP
Key Number: The rst two digits represent the step
number. The third digit represents the piece. Note
that if the part is used in multiple steps then the
number only reects the rst step it is used in.
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
Step 1: Inventory Parts - Read This Before Starting Assembly
• Please refer to Page 6 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the key number stamped on the ends of the boards.
Organize the wood pieces by step, as per the key numbering system below.
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)
MODEL NUMBER: F29015
TRACKING NUMBER (from ID Plaque):
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton.The tracking number is
located on the KidKraft ID Plaque (9320370).
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
[phone]
[email protected]
For online parts replacement visit
https://parts.kidkraft.eu/
1.800.933.0771 or 972.385.0100
[email protected]
[email protected]
For online parts replacement visit
https://parts.kidkraft.com/
14 [email protected]

xxx
x
x
xx x
xxx
x
x
xx x
xxx
x
x
xx x
Step 2: Swing Beam Assembly
Make sure triangle is
tight against beam
Fig. 2.4 WARNING: For your child’s
safety, orientate the swing hangers
as shown to ensure your swing will
have proper swing motion when
installed. Failure to do so could
result in premature failure of the
swing hanger or swing chain.
A: In the middle holes of (1825) Back Beam install
2 Bolt-Thru Swing Hangers (g. 2.4) making sure
the swing hangers are oriented in the direction
shown in g. 2.4 to maintain proper swing motion.
B: In the end holes of (1826) Front Beam install 4 Bolt-
Thru Swing Hangers (g. 2.1) making sure the swing
hangers are oriented in the direction shown in g. 2.4 to
maintain proper swing motion.
C: Attach 1 Triangle Plate
to the ends of each (1826)
Front Beam and (1825) Back
Beam using 1 (G1) 5/16 x
1-1/2” Hex Bolt (with lock
washer, at washer and
t-nut) in the hole indicated in
g. 2.2 & 2.3. Correct hole
usage is very important.
Important!
Swing End
(With Overhang)
Important!
Fort End Side
(No Overhang)
D: Attach 1 (H7) 1/4 x 5-1/2” Hex Bolt (with lock washer, at washer and t-nut) to the ends of each (1826) Front
Beam and (1825) Back Beam. The bolts do not attach to anything, but MUST be installed to the beams to prevent
splitting and checking of wood. (g. 2.2 & 2.3)
Swing End
(With Overhang)
Fort End Side
(No Overhang)
Wood Parts Hardware
Bolt-Thru Swing
Hangers
4 x 1/4 x 5-1/2” Hex Bolt
 (1/4”atwasher,1/4”lockwasher,1/4”t-nut)
4 x 5/16 x 1-1/2” Hex Bolt
 (5/16”atwasher,5/16”lockwasher,5/16”t-nut)
H7
G1
1 x Bolt-Thru Swing Hangers (pkg of 6)
1 x Triangle Plate (pkg of 4)
1 x Front Beam 2 x 6 x 83-5/8”
1 x Back Beam 2 x 6 x 83-5/8”
1826
1825
Triangle
Plates
G1 H7
1826
1825
1/4” Flat
Washer 1/4” Lock
Washer
1/4”
T-Nut
5/16” Flat
Washer
5/16” Lock
Washer
5/16”
T-Nut
1826
1825
H7
Other Parts
Fig. 2.2
Fig. 2.3
G1
H7
G1 G1
H7
Fig. 2.1
Bolt-Thru
Swing
Hangers
Triangle Plates
15 [email protected]

Step 3: Swing End Assembly
A: Attach 2 (1863) SW Posts to (1856) SW Upright using 2 (G4) 5/16 x 4” Hex Bolts (with lock washer, at
washer and t-nut). (g. 3.1)
B: Attach (1862) SW Support to both (1863) SW Posts and (1856) SW Upright using 3 (G5) 5/16 x 4-1/2” Hex
Bolts (with lock washer, at washer and t-nut). (g. 3.1)
Wood Parts Hardware
2 x 5/16 x 4” Hex Bolt
 (5/16”lockwasher,5/16”atwasher,5/16”t-nut)
3 x 5/16 x 4-1/2” Hex Bolt
 (5/16”lockwasher,5/16”atwasher,5/16”t-nut)
G4
G5
2 x SW Post 2 x 4 x 86-11/16”
1 x SW Support 5/4 x 4 x 46-1/2”
1 x SW Upright 2 x 4 x 48-5/16”
1862
1863
1856
5/16” Flat
Washer
5/16” Lock
Washer
5/16”
T-Nut
Fig. 3.1
1863 1862
1856
G4
1863
G5
5/16” Flat
Washer
5/16” Lock
Washer
5/16”
T-Nut
16 [email protected]

Step 4: Attach Swing End to Swing Beam
A: Place (4919) SW Rail Block in the centre between (1826) Front Beam and (1825) Back Beam and attach with
1 (H8) 1/4 x 4-1/4” Hex Bolt (with lock washer, at washer and t-nut). (g. 4.1 & 4.2)
B: Attach Swing Beam Assembly to the side of the Swing End Assembly with the overhang (g. 4.3 & 4.4) using
1 (G5) 5/16 x 4-1/2” Hex Bolt (with lock washer, at washer and t-nut) in the top hole of Triangle Plate and 1 (G8)
5/16 x 2” Hex Bolt (with 2 at washers and lock nut) in the bottom hole of Triangle Plate. (g. 4.4) Make sure
Swing End Assembly ares out at an angle. (g. 4.3)
Wood Parts Hardware
Fig. 4.2
1/4” Flat
Washer
1/4” Lock
Washer
1/4”
T-Nut
H8
4919
G5
5/16”
T-Nut
5/16” Flat
Washer
5/16” Lock
Washer
5/16” Flat
Washer
5/16”
Lock Nut
G8
1826
Side with
overhang
1 x SW Rail Block 2 x 4 x 5-3/8”
4919 1 x 1/4x4-1/4”HexBolt(1/4”lockwasher,1/4”atwasher,1/4”t-nut)
1 x 5/16x4-1/2”HexBolt(5/16”lockwasher,5/16”atwasher,5/16”t-nut)
1x 5/16x2”HexBolt(5/16”atwasherx2,5/16”locknut)
H8
G5
G8
Fig. 4.1
Fig. 4.3 Fig. 4.4
1825
1826
1825
100o1826
1825
17 [email protected]

Step 5: Cafe Wall Assembly
A: Attach (1914) Cafe Ground with 4 (H2) ¼ x 2” Hex Bolts (with lock washer, at washer and t-nut); (1760)
Floor using 2 (H2) ¼ x 2” Hex Bolts (with lock washer, at washer and t-nut) in the bottom holes, noticing hole
locations; (1923) Side Top with 2 (H2) ¼ x 2” Hex Bolts (with lock washer, at washer and t-nut) and (1981) Top
Side with 2 (H2) ¼ x 2” Hex Bolts (with lock washer, at washer and t-nut) to 2 (1500) Posts as shown in g. 5.1,
5.2 and 5.3.
Note: Pre-drill all holes using a 1/8” drill bit before installing the lag screws.
B: Make sure assembly is square and then fasten (1760) Floor to (1500) Posts in the top holes using 2 (LS1) ¼
x 1-1/2” Lag Screws (with at washer). (g. 5.1 and 5.3)
Wood Parts Hardware
1 x Cafe Ground 1 x 5 x 41-1/2”
2 x Post 2 x 4 x 83”
1 x Floor 1 x 6 x 26-7/8”
1 x Side Top 1 x 4 x 26-7/8”
1 x Top Side 1 x 4 x 36”
1914
1500
1760
1923
1981
10 x 1/4x2”HexBolts(1/4”lockwasher,1/4”atwasherand1/4”t-nut)
2 x 1/4”x1-1/2”LagScrews(1/4”atwasher)
H2
LS1
Fig. 5.1 Fig. 5.2
Fig. 5.3
1914
1981
1914
1760
H2
1500
1500
1500
1500
1760
1923
H2
H2
LS1
LS1
H2
1/4” Lock
Washer
1/4” Lock
Washer
1/4” Flat
Washer
1/4” Flat
Washer
1/4”
T-Nut
1/4”
T-Nut
H2
H2
Notice the
hole
location
18 [email protected]

Step 6: Swing Wall Assembly
Part 1
A: Attach (1928) Lower Side, noticing the side the bolt hole on the extended end is on, using 4 (H2) 1/4 x 2” Hex
Bolts (with lock washer, at washer and t-nut); (1924) SW Floor (in the bottom holes) and (1925) SW Top using 2
(H2) 1/4 x 2” Hex Bolts (with lock washer, at washer and t-nut) for each board to 2 (1500) Posts. (g. 6.1)
Note: Keep all bolts loose.
B: On the side indicated in g. 6.1, attach (0369) Lower Diagonal to (1928) Lower Side with 1 (H2) 1/4 x 2” Hex
Bolt (with lock washer, at washer and t-nut).
Wood Parts Hardware
1 x SW Floor 1 x 6 x 26-7/8”
1 x SW Top 1 x 4 x 36”
1 x Lower Side 1 x 5 x 59-11/16”
1 x Lower Diagonal 2 x 3 x 37”
2 x Post 2 x 4 x 83”
1924
1925
1928
0369
1500
9 x 1/4 x 2” Hex Bolts
(1/4”lockwasher,1/4”atwasherand1/4”t-nut)
H2
Fig. 6.1
Step 6 Part 1
1924
1500
1925
0369
1928
H2
H2
H2
1/4” Lock
Washer
1/4” Flat
Washer
1/4”
T-Nut
1/4”
T-Nut
Notice bolt holes
on this side
Notice the hole
locations of (1924)
SW Floor.
19 [email protected]

Step 6: Swing Wall Assembly
Part 2
C: Place (1861) SW Mount across (1924) SW Floor and (1925) SW Top and attach using 2 (G4) 5/16 x 4” Hex
Bolts (with lock washer, at washer and t-nut) as shown in g. 6.2. Notice the side hole locations are towards the
top of the board.
Note: Pre-drill all holes using a 1/8” drill bit before installing the lag screws.
D: Make sure assembly is square then fasten (1924) SW Floor to (1500) Posts in the top holes using 2 (LS1)
1/4 x 1-1/2” Lag Screws (with at washer); and (0369) Lower Diagonal to (1500) Post with 1 (LS3) 1/4 x 3” Lag
Screw (with at washer). (g. 6.2)
E: Tighten all bolts.
Wood Parts Hardware
1 x SW Mount 2 x 4 x 38-1/8”
1861 2 x 5/16x4”HexBolts(5/16”lockwasher,5/16”atwasherand5/16”t-nut)
2 x 1/4”x1-1/2”LagScrews(1/4”atwasher)
1 x 1/4”x3”LagScrews(1/4”atwasher)
G4
LS1
LS3
Step 6 Part 2
Fig. 6.2
1925
1924
1500
1861
G4
G4
LS1
LS3
LS1
5/16” Lock
Washer
5/16” Flat
Washer
1/4” Flat
Washer
1/4” Flat
Washer
5/16”
T-Nut
Notice the hole
locations
20 [email protected]