KidKraft P280115 User manual

INSTALLATION AND OPERATING INSTRUCTIONS
10/25/20199400115
Table of Contents
Warnings and Safe Play Instructions..........pg. 2
Keys to Assembly Success ....................pg. 3
About Our Wood – Limited Warranty.........pg. 4
Part ID .................................... pg. 5-7
Step-By-Step Instructions ................ pg. 8-32
COOPER PLAYHOUSE FSC EU - P280115
2 - 3 Hrs
TWO PERSON
ASSEMBLY
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
[email protected]
[email protected]
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
KidKraft Netherlands BV
Olympisch Stadion 8
1076 DE Amsterdam
The Netherlands
[email protected]
[phone] M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/
3’8”
1.12m
16’9.5”
5.12m
17’1.1”
5.21m
3’11.7”
1.21m
FOR OUTDOOR FAMILY
DOMESTIC USE ONLY
WARNING To reduce the risk of serious injury or death, you must read and follow these instrucons.
Keep and refer to these instrucons oen and give them to any future owner of this play set.
Manufacturer contact informaon provided below.
OBSTACLE FREE SAFETY ZONE - 16’9.5” x 17’1.1” (5.12 x 5.21 m)
CAPACITY - 3 Users Maximum, Ages 2 to 10.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
WARNING. Only for domesc use.

2
Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have
occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards.
Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children
using this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
Dress children with well fitting and full foot enclosing
footwear.
Check for splintered, broken or cracked wood; missing,
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
Replace defective parts in accordance with manufaturer’s
instructions.
Do not allow children to wear open toe or heel footwear
like sandals, flip–flops or clogs.
Do not permit climbing on equipment when it is wet.
Do not permit rough play or use of equipment in a manner
for which it was not intended. Standing or climbing on or
jumping from the roof.
WARNING – Safe Play Instructions
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
STRANGULATION HAZARD
•NEVER allow children to play with ropes,
clotheslines, pet leashes, cables, chains or cord-like
items when using this playhouse or to attach these
items to the playhouse.
•NEVER allow children to wear loose fitting clothing,
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this playhouse.
•NEVER allow children to wear bike or sport helmets
when using this playhouse.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can
reduce the likelihood of the playhouse tipping over
and loose-fill surfacing materials washing away during
heavy rains.
DO NOT allow children to play on the playhouse until
the assembly is complete.
PLACEMENT
Place the toy on a level surface at least 2m from any
structure or obstruction such as fences, garages, house,
overhanging branches, laundry or electical wires.
WARNING
HARDWARE:
Check metal parts for rust. If found,
sand and repaint using a non-lead paint
complying with 16 CFR 1303.
Inspect and tighten all hardware. On
wood assemblies DO NOT OVER-
TIGHTEN as to cause crushing and
splintering of wood.
Check for sharp edges or protruding screw threads, add
washers if required.
WOOD PARTS:
Check all wood members for deterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
Applying a water repellent or stain (water-based) on a yearly
basis is important maintenance to maintain maximum life
and performance of the product.
Instructions for Proper Maintenance
Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with
all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your
Playhouse, it is important that you, the owner, properly maintain it.
Check the following at the beginning of the play season:
Check twice a month during play season:
HARDWARE:
Inspect for tightness. Must be firmly against, but not crushing the wood.
DO NOT OVER-TIGHTEN. This will cause splintering of wood.
Check for sharp edges or protruding
screw threads. Add washers if required.
If you dispose of your playhouse: Please disassemble and dispose of your unit so that it does not create any unreasonable
hazards at the time it is discarded. Be sure to follow your local waste ordinances.
2

3
Part Identification Key
On each page, you will find the parts
and quantities required to complete the
assembly step illustrated on that page.
Here is a sample.
Key Number: The first two digits
represent the step number. The third
digit represents the piece. Note that
if the part is used in multiple steps
then the number only reflects the
first step it is used in.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot holes to
avoid splitting wood. Only a flat washer
is required. For ease of installation
liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” is slightly
larger than 1/4”.
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed
threads. If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.
This identifies information that requires special
attention. Improper assembly could lead to an
unsafe or dangerous condition.
Where this is shown, 2 or 3
people are required to safely
complete the step. To avoid
injury or damage to the
assembly make sure to get
help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8” & 3/16” Bit
Tighten
Bolts
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Tape Measure
• Standard or Cordless Drill
• Pencil
• Safety Glasses
• Adult Helpers
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
No Yes
Lag Assembly
Bolt Assembly
Flat Washer
Lag Screw
Hex Bolt
Lock
Washer
Flat
Washer
Before mounting Lag
Screw, use factory drilled
holes as guides to drill 1/8”
pilot holes
T-Nut
(Hammer into place)
Do not crush wood!
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer

4
About Our Wood
KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use.
Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to
weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is
different than the interior of the wood. As the climate changes, moisturemoves in or out of the wood, causing tension which can
result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of
the product:
1. Checking is surface cracks in the wood alongthe grain. A post (4” x 4”)will experience more checkingthan aboard (1” x 4”)
becausethesurface and interior moisture content will vary morewidely than in thinner wood.
2. Warping results from any distortion (twisting, cupping) fromtheoriginal plane of theboard and often happens fromrapid
wetting and dryingof the wood.
3. Fading happens as anatural change in the wood color as it is exposed to sun-light and will turn a grey over time.
province to province. This warranty excludes all consequential damages, however, some states do not allow the
limitation or exclusion of consequential damages, and therefore this limitation may not apply toyou.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption
during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, applying a water repellant or
stain on a yearly basis is important maintenance. (see your local stain and paint supplier for a recommended product)
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are
concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.
warranty service.
5Year Limited Warranty
KidKrat warrants that this product is free from defect in materials and workmanship for a period of
one year from the original date of purchase. In addition, lumber is warranted for 5years against
structural failure due to rot and insect damage. All other parts, such as hardware, swings, rides,
accessories, and slides carry a one-year warranty only.
This warranty applies to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your Play System. Failure by the owner
to maintain the product according to the maintenance requirements may void this warranty. This
warranty does not cover any inspection cost.
This LimitedWarranty does not cover:
•Labour for replacement of any defective item(s);
•Incidental or consequential damages;
•Cosmetic defects which do not affect performance or integrity;
• Vandalism; improper useor installation; acts of nature;
• Minor twisting, warping, checking, or any other natural occurring properties of wood that do not
affect performance or integrity.
KidKraft products have been designed for safety and quality. Any modifications made to the
original product could damage the structural integrity of the unit leading to failure and possible
injury. KidKraft cannot assume any responsibility for modified products. Furthermore, modification
voids any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a KidKrat Play
System be used in public settings such as schools, churches, playgrounds,parks, day cares and the like. Such
use may lead to product failure and potential injury. Any and all public use will void this warranty.
KidKraft disclaims all other representations and warranties of any kind, express or implied.

5
Part Identification (Reduced Part Size)
2pc. - 0921 - 31.8 x 76.2 x 740 mm - FSC - 48092137
2pc. - 0922 - 31.8 x 76.2 x 740 mm - FSC - 48092237
1pc. - 0923 - 34.9 x 85.7 x 1054 mm - FSC - 48092337
2pc. - 0926 - 12.7 x 25.4 x 1066.8 mm - FSC - 48092637
2pc. - 0920 - 31.8 x 31.8 x 1020.9 mm - FSC - 48092037
2pc. - 0927 - 12.7 x 50.8 x 762 mm - FSC - 48092737
2pc. - 0928 - 12.7 x 50.8 x 355.6 mm - FSC - 48092837
2pc. - 0924 - 15.9 x 85.7 x 365.8 mm - FSC - 48092437
4pc. - 0925 - 15.9 x 85.7 x 133.4 mm - FSC - 48092537
2pc. - 0929 - 25.4 x 50.8 x 1052 mm - FSC - 48092937
3pc. - 0930 - 23.8 x 23.8 x 400 mm - FSC - 48093056
1pc. - 0931 - 23.8 x 23.8 x 1065 mm - FSC - 48093156
1pc. - 0933 - 23.8 x 57.2 x 674.5 mm - FSC - 48093373
1pc. - 0935 - 15.9 x 76.2 x 1050 mm - FSC - 48093537
1pc. - 0936 - 15.9 x 59.3 x 1050 mm - FSC - 48093637
1pc. - 0932 - 23.8 x 23.8 x 508 mm - FSC - 48093256
1pc. - 0871 - 25.4 x 425.5 x 947.2 mm
- FSC - 478087173
1 x 16-3/4 x 38-11/32"
1pc. - 0934 - 23.8 x 63.5 x 127 mm - FSC - 48093456
1-1/4 x 3 x 29-1/8"
1-1/4 x 3 x 29-1/8"
1-3/8 x 3-3/8 x 41-1/2"
1/2 x 1 x 42"
1-1/4 x 1-1/4 x 40-3/16"
1/2 x 2 x 30"
1/2 x 2 x 14"
5/8 x 3-3/8 x 14-3/8"
5/8 x 3-3/8 x 5-1/4"
1 x 2 x 41-13/32"
15/16 x 15/16 x 15-3/4" 15/16 x 15/16 x 20"
15/16 x 15/16 x 41-15/16"
15/16 x 2-1/4 x 26-9/16" 15/16 x 2-1/2 x 5"
5/8 x 3 x 41-11/32"
5/8 x 2-3/8 x 41-11/32"

6
1pc. - 0872
- 106.8 x 1117.6 x 1092.2 mm
- FSC - 478087273
4-3/16 x 44 x 43"
Part Identification (Reduced Part Size)
0872
0869
0870
0867
0868
0865
0866
0867
0868
9325687
If you need to order parts,
please order below part#
9325687 - Wall Hinge - 1pc.
S39 - 52012903 - Wood Screw #5 x 3/4" - 1pc.
0865 - 478086556 - Front Wall Panel - FSC - 1pc.
0866 - 478086656 - Frame - FSC - 1pc.
0867 - 478086756 - Side Panle A - FSC - 1pc.
0868 - 478086856 - Side Panel B - FSC - 1pc.
0869 - 478086956 - Back Wall Left - FSC - 1pc.
0870 - 478087056 - Back Wall Right - FSC - 1pc.

7
Part Identification (Reduced Part Size)
Hardware Identification (Actual Size)
2x
- (9207711)
1x
- (9207713)
1x
- (P-U-4825)
1x
- (9330459) (2pk)
2x
- (9207712)
1x
- (3200710)
4pc. S33 - #8 x 1" (25.4mm) - (52043510) 32pc. S0 - #8 x 7/8" (22.2mm) - (52933505)
4pc. S5 - #8 x 1/2" (12.7mm) - (52433502)
44pc. S20 - #8 x 1-3/8" (34.9mm) - (52043516)
18pc. S37 - #7 x 5/8" (15.9mm) - (52433009)
36pc. S15 - #8 x 1-3/4" (44.5mm) - (52043513)
1pc. D4 - #2 x 2 (50.8mm)- (9200014)
24pc.
S3
- #8 x 2-1/2" (63.5mm) - (52043522)
14pc. S11
- #8 x 2" (50.8mm) - (52043520)
2pc. S38
- #7 x 1-1/8" (28.6mm) - (52433014)
Note: Hardware bag includes extra hardware
1x
- (9320371)

8
B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.
Quantity Key Number Part Description,
Part Size
1X 131 Cafe Top 15.9 x 127 x 1225.6 mm
Step 1: Inventory Parts - Read This Before Starting Assembly
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton.
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
• Please refer to Page 3 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the key number stamped on the ends of the boards.
Organize the wood pieces by step, as per the key numbering system below.
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)
MODEL NUMBER: P280115
[phone]
[email protected]
For online parts replacement visit
https://parts.kidkraft.eu/
1.800.933.0771 or 972.385.0100
[email protected]
[email protected]
For online parts replacement visit
https://parts.kidkraft.com/

9
Step 2
0872
0872
1 x - 4-3/16 x 44 x 43” (106.8 x 1117.6 x 1092.2 mm)
0872
Wood Parts

10
Step 3
S15
S15
S15
S15S15S15S15
S15
0930
0930
0930
0930
2 x 15/16 x 15/16 x 15-3/4” (23.8 x 23.8 x 400 mm)
Wood Parts Hardware
0930 8 x #8 x 1-3/4” (44.5mm)
S15

11
Step 4
0930
0931
0930
0931
S15
S15 S15
S15
S15
S15
S15
S15
1 x 15/16 x 15/16 x 15-3/4” (23.8 x 23.8 x 400 mm)
1 x 15/16 x 15/16 x 41-15/16” (23.8 x 23.8 x 1065 mm)
Wood Parts Hardware
0930
0931
8 x #8 x 1-3/4” (44.5mm)
S15

12
Step 5
S3
S3
S3
S3
S3
S3
S3
S3
S3
S3
S3
S3
S3
S3
S3
Hardware
12 x #8 x 2-1/2” (63.5mm)
S3

13
Step 6
0932
S15 S15 S15 S15
1 x 15/16 x 15/16 x 20” (23.8 x 23.8 x 508 mm)
Wood Parts Hardware
0932 4 x #8 x 1-3/4” (44.5mm)
S15
S15
S15
S15
S15
0932

14
Step 7
0933
0933
S15
S15
S15
S15
S11
S11
S11
S11
1 x 15/16 x 2-1/4 x 26-9/16” (23.8 x 57.2 x 674.5 mm)
Wood Parts Hardware
0933 2 x #8 x 1-3/4” (44.5mm)
2 x #8 x 2” (50.8mm)
S15
S11

15
Step 8
S37
S37
S37
S37
Hardware
9207711
2 x #7 x 5/8” (15.9mm)
S37
Other Parts
1 x
9207711
22” (560mm)
0871
1 x 1 x 16-3/4 x 38-11/32” (25.4 x 425.5 x 974.2 mm)
Wood Parts
0871
0871

16
Step 9
22” (560mm)
15” (381mm)
S37
S37 S37
S37
9207711
9207711
9207713
9207713
Hardware
9207711
9207713
4 x #7 x 5/8” (15.9mm)
S37
Other Parts
1 x
1 x
0871
S37 S37
S37
S37

17
Step 10
Hardware
2 x #8 x 1/2” (12.7mm)
S5 P-U-4825
Other Parts
1 x
P-U-4825
P-U-4825
S5
S5
S5
S5

18
Step 11
Hardware
9207712
6 x #7 x 5/8” (15.9mm)
S37
Other Parts
2 x
20mm
25/32”
S37
S37
9207712
S37
9207712
S37

19
Step 12
S37
S37
S37
5/8”
15.9mm
Hardware
6 x #7 x 5/8” (15.9mm)
S37

20
Step 13
S38
S15
S15
S38
Hardware
2 x #8 x 1-3/4” (44.5mm)
2 x #7 x 1-1/8” (28.6mm)
S15
S38
9207713
Other Parts
1 x
9207713
0934
0934
9207713
1 x 15/16 x 2-1/2 x 5” (23.8 x 63.5 x 127 mm)
Wood Parts
0934
Important: Use a hand
held screw driver and
DO NOT over tighten.