Kidzpace Family Activity Center Quick start guide

FAMILY ACTIVITY CENTER
INSTALLATION & OPERATIONAL
INSTRUCTIONS
SOCCER/FOOSBALL

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
2
Assembly Instructions
UNPACKING AND TABLE SETUP
List of tools needed:
Wire Cutters
Large Phillips head Screwdriver
Adjustable wrench
These instructions should be followed to correctly unpack and assemble your new
Soccer/Foosball table:
NOTE: For reasons of safety and efficiency, Kidzpace strongly recommends that a
minimum of 2 people be involved in the setup of our Soccer/Foosball table.
(Weighs 225 lbs)
Once assembled, your Soccer/Foosball table is quite large and may not fit through your
doors. For this reason we recommend that you assemble your table in the room you
intend it to be used.
Unpacking and Table Setup
Lay the box flat on the floor -- note: one section of the box will be labeled "This Side Up." Cut
the banding straps and remove the top portion of the box completely. Lower the sides of the
box bottom by cutting or tearing vertically at all four (4) corners.
Keep the table cabinet lying on the carton and
look for the keys attached to one of the
bead score counters at each end of the table.
Open your Soccer/Foosball table by
unlocking and lifting the top upward. Locate
the wooden prop arm fixed to the cabinets
inside left corner. Use the prop arm to
support the top section of the table open.

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
3
Remove the following items from the inside
of the table.
Hardware Pouch Contains:
• Eight (8) Leg Bolts
• One (1) Allen Key
• Thirty-three (33) screws (one spare)
• Four (4) Red & Yellow player control
rod caps.
• Nine (9) Red & Yellow bearing spacers
with long pins. (one spare/ color)
• Nine (9) Red & Yellow bearing spacers
with short pins. (one spare/ color)
• Four (4) Red & four (4) Yellow
Handles.
• Eight (8) Black Bearings.
• Ten (10) Balls.
Player Control Rods Pouch Contains:
• Four (4) Red & four (4) Yellow player
control rods.
• One (1) Goalie each. (1 player / rod)
• One (1) Defense each. (2 players / rod)
• One (1) Mid Fielder each. (5 players /
rod)
• One (1) Forward each. (3 players / rod)

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
4
Leg Leveler Pouch Contains:
• Four (4) Leg Levelers
• Four (4) Threaded Inserts
• Four (4) Lock Nuts
• Two (2) Sets of Legs
• Two (2) Ball Ramps
Coin Denomination Package (for approved countries)
Included are:
• Coin Mechanism that accepts coin or tokens (available from Kidzpace)
• Three (3) large and three (3) small stickers. (.50, .75, 1.00)
After removing all parts, close tabletop and lock with key provided.
Leg Assembly
Carefully stand the table on its end, using the cardboard box under the table to protect it from
scratches.
• Attach the four (4) leg levelers to the bottoms of the legs.
Begin by tapping the threaded insert into the
hole with a hammer until the insert is
completely inside.

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
5
Insert the lock nuts on the leg levelers threaded
end.
Screw the leg leveler ¾ of the way into the
metal insert. The depth will determine how high
or low your table will stand.
Attach the legs to the table using the Allen
bolts and the L-shaped wrench, and tighten.
Note: Legs are to be attached with an outward angle for stability.
• Restore table to its upright position.
• Level the table by adjusting the nut located at the leveler base with a wrench.
• Once level, tighten the lock nut at the legs base to prevent the leveler from moving.
• With the table upright and level, open the top again by unlocking and support with prop
arm. Set both ball chutes in the right position, by making sure they rest on their holders.
• Then close and lock the table to proceed to installing the player rods.

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
6
Installing Player Rods
Before installing the player rods it is necessary to remove the glass top from the table.
Unscrew the two (2) bolts on each side of one
end of the upper part.
Take away the wooden locking rail and slide
the tempered glass top out.
Remove the glass top carefully from the table.
Set the glass top vertically in a safe place while
player rods are installed.
Important!!
Locate the Player Field Diagram (next page) for the proper locating and positioning of the
eight (8) player control rods.

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
7
Installing Player Rods (cont)
Player Field Diagram
Yellow
Counter
Red
Counter
Coin Mech.
Yellow
Handle
Side
Red
Handle
Side
Placement of player control rods
• Goalies (1 player per rod) are located at each end of the table. Yellow goalie
defends the Yellow counters facing the play field and the Red goalie defends the red
counters facing the playing field.
• Defense (2 players per rod) are located directly in front of the same color goalie and
facing the same direction. Red in front of Red and yellow in front of yellow.
• Forwards (3 players per rod) are located in front of and opposing the other colors
defense. For instance, the red forwards would face the yellow goal.
• Mid Fielders (5 players per rod) are on the same side of the field as their goalie and
face in the direction of the opposing goal.

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
8
Installing Player Rods (cont)
Insert the end without the bushing (handle end)
of rod through the appropriate hole and side of
table, ensuring the player is facing the correct
direction and color.
Insert the opposite end with the bushing into
the hole on the other side of the table.
Line up the pins of the covering cap into the
holes.
Insert screws into the holes, not tightening until
all rods are installed.
• Repeat for all player control rods, following the player field diagram ensuring all
players are in the proper location and facing the correct direction and color.

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
9
Installing Player Rods (cont)
Slide the bearing onto the player control rod
from the handle end and locate inside the
tables edge, leveling the rod.
Start with the long pin spacers (same color as
players) on the inside of the player field with
the pins pointing towards handle location.
Snap together both halves and slide pins into
holes on inside of the table.
Snap together both spacer halves with short
pins (same color as players) and slide onto rod
from handle end, inserting pins into holes on
the outside of the table.
Insert screws into the holes from the outside of
the table to secure the retainer in place, be
sure not to tighten yet.
• Repeat bearing assembly for all player control rods.

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
10
Installing Player Rods (cont)
With all spacers and caps in place, assuring all
players are in their correct positions, begin to
tighten the screws.
Holding the spacer with your fingers on the
inside of the table will keep it in place while
tightening.
Repeat for all caps and spacers
Handle Installation
Align the same color handles to players, push
the telescoping rods completely in before
gently tapping the handle onto the rod, making
sure to cover the ridges on the rod.
After handle installation, try to pull off each of
them. If installed correctly they will not move.
Caution: Do not install handles if the plastic feels cold, allow them to warm before installing.
Replacing Glass Cover to Table
Prior to replacing glass top to table, make sure that the players and play field have been cleaned
of any debris during the setup process. Also, clean both sides of the glass top before replacing.
(See table-cleaning instructions)
Slide glass top carefully into the groves of the
table.
Replace the end bracket by securing the two
(2) screws removed earlier.
NOTE: If this end bracket does not line up easily, check the opposite end of the table to ensure
the glass top has fit into the end grove. To do so push down gently on the metal edging and slide
glass top in.

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
11
Installing Ball Ramps
• Unlock table with key and secure open with wooden prop arm.
One ball ramp has to be set into place at each
end of the table. With the wide end of the
ramp facing the end of the table, insert the
downward flange into the slot inside the table.
• Test the ramps by dropping a couple of balls down each ramp to see them come to rest
in the ball storage area.
• With the ramps working, load the rest of the balls into the storage area, lower tabletop
and lock.
Coin and/or Token Option. (For approved countries only)
• Our coin/token mechanism gives your Soccer/Foosball table two (2) possibilities other
than Free Play.
- Coin/Token Option: your table would accept coins or tokens, up to three (3)
coins/tokens.
• This mechanism allows the use of coins or tokens (purchased from Kidzpace), giving you
reward and marketing opportunities to your customers.
Installing Coin Mechanism.
• Remove the free play block, by removing the screws from the inside of the table.
Remove lever taped to the top of coin box.
Add lever to coin mechanism and secure
with lock nuts.

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
12
Installing Coin Mechanism (cont)
With lever and coin mechanism together,
swing lever to photos position.
Insert lever and coin mechanism through
opening from front of the table. If it seems
tight, bend the lower flange up slightly and
insert as shown. Remember to readjust
flange after installed.
With lever and coin mechanism inserted
through opening. Swing lever around and
under the release bar and tighten the nut
securing the lever.
With lever secured insert four (4) coin
mechanism screws and tighten.
Table Test
• With the table assembled it now time to test you're Soccer/Foosball table.
• Press the free play button or insert correct coinage into coin mechanism and push
completely in. It takes a firm push to release the balls from storage to the on
deck area.
• Count the balls to ensure all ten (10) have been released.
• Slide one (1) ball into the play field and play!

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
13
Push Chute Coin vend change instructions and Parts diagram

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
14
Game Counter
Each table is equipped with a counter inside
the table.
Each time a player pushes the free play
button or pays for a game, the releasing of
the balls triggers the counter.
Example: In one collection period, the game counter reads 500 plays (the difference between the
previous and present counter readings) and the coin box has $250.00 dollars inside for a table
set up for $.50 cents per play.
Table Cleaning Instructions
Exterior
• Basic cleaning of the exterior of the table, (glass surface, sides and handles) to be
cleaned with a daily sanitizer.
• A more thorough cleaning is recommended with degreaser.
• Internal cleaning should be performed inside the table cabinet.
Table Cleaning Instructions (cont)
Interior
• To clean the Player Field under the glass top, you begin by unlocking the tabletop and
support it with the prop arm.
Locate the Player Field locks, one at each
end.
Pull lock lever to release, repeat at other
end and carefully lower player field.

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
15
Clean as needed, being careful not to rub
the white lines with alcohol or alcohol-based
detergents, which may cause them to fade.
• Close and lock the player field to the top section of the table.
• Lower prop arm and close tabletop and lock with key.
Trouble Shooting
Jammed Push Chute
• Open the table and support with the prop arm.
• Locate the coin mechanism inside the table and clear the debris that is causing the jam.
Please refer to your Push Chute Parts diagram for identification of the following
instructions.

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
16
Parts Diagram

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
17
Part no.
1 front lower wooden part
2 back lower wooden part
3 upper front wooden part
4 upper back wooden part
5 centre wooden part
6 upper wooden part either end
7 glass mounthing either end
8 wooden goalmouth
9 threaded insert for leg leveler
10 leg leveler
11 plastic laminate playfield with Kidzpace logo
12 wooden game bottom
13 wooden legs
16 white plastic corner for playfield (left)
17 white plastic corner for playfield (right)
18 complete ball release mechanism (metal box)
18 bis coin counter
19 ball chute (left / right)
20 cash box
21 inside goal net in metal
22 score counter (red / yellow)
24 bolt for lowering playfield
27 metal part no. 27 (hinge)
28 metal part no. 28 (hinge)
29 metal part no. 29 (hinge)
30 metal part no. 30 (hinge)
31 lock with keys
32 couple of bars for lock (56mm & 66mm)
33 metal part no. 33
34 metal part no. 34
35 metal part no. 35
37 metal part no. 37
40 coin mechanism
41 ball chute holder
53 plastic handle (red / yellow)
59 metal part no. 59 for art. 18
60 metal part no. 60 for art. 18
61 top glass wooden locking rail
62 metal part no. 62 for art. 31
65 metal part no. 65 for art. 20
71 metal plate for legs
74 bolt for leg
76 sheet of glass for covering the playfield
80 outer ball security cage
82 metal part no. 82
83 metal part no. 83
90 metal part no. 90
91 metal part no. 91
92 metal part no. 92 for art. 28
95 metal part no. 95 for art. 27

KIDZPACE INTERACTIVE INC. P.O. Box 550 Collingwood, Ontario, Canada L9Y 4B2
NORTH AMERICA - Tel: [phone] * Fax: [phone] * Toll-Free 1- 800-668-0206
INTERNATIONAL – Tel: [phone] * Fax: [phone]
18
Kidzpace Service Program
Interactive Play - Coin Operated Equipment
Contact
Telephone
Numbers
Warranty
Maintenance
& Cleaning
Procedures
To order new and replacement parts, warranty
parts or technical assistance call: Scott Marritt
Kidzpace Interactive, Inc.
55 Sanford Fleming Dr.
Collingwood, Ontario L9Y 5A6
Tel: [phone]
Fax: [phone]
1-800-668-0206
Web Site: www.kidzpace.com
Kidzpace warranty
90 Days – Parts only, from time of delivery.
Daily: Glass surface, sides, Handles, posts
should be cleaned daily with sanitizer.
Monthly: a more thorough cleaning is
recommended with degreaser including the glass
surface, handles and counters.
Y
early: an internal cleaning should be performed
inside the table cabinet.
Cleaners should be applied directly to the
cleaning cloth, not the surface.
Rubbing alcohol or McDonald’s sanitizer -
degreaser is best for cleaning the table surface
from stubborn stains.
Contact Scott Marritt at the above number for
more details.
DO NOT USE AMMONIA-BASED CLEANERS,
SCOURING COMPOUNDS, OR SOLVENTS, SUCH AS
A
CETONE, GASOLINE, ETC. AS THESE WILL DAMAGE
Y
OUR UNIT.
Important Staff Notice
Please Post.