Kilews IMPACT Series User manual

IMPACT SERIES Cordless Screwdriver
OPERATION AND MAINTENANCE MANUAL
KILEWS INDUSTRIAL CO., LTD.
http://www.kilews.com
Y2F135A-E-002
SKC-PTI-100B


1
Please read manual carefully before operating the rechargeable
impact screwdriver.
Icon Instruction
Read manual Warning Recycle Indoor use only
No humidity No fire No disassemble No disposal CE certificate
Accessories
Item
Quantity
Unit
Manual
1
PCS
Guarantee Card
1
PCS
Waist hook
1
PCS
Screw M3*0.5P*10LT
1
PCS
Socket Extension (B)
1
PCS
BIT(B)
2
PCS


2
Warning
Read all instructions and make sure the appearance of the device has no damage before you use it.
Failure to follow all instructions listed below may result in electric shock fire and/or serious injury.
1. Keep the working area nice and clean.
1.1 Mess and dark areas may cause of accidents.
1.2 Keep the device away from rain or moisture to decrease the risk of electric shock or short-
circuiting occurred.
2. Be alert to workplace safety
2.1 Use the device under a well lit and clean environment.
2.2 Keep children and other people away unless the person has been assigned for the task to avoid
the danger of injury.
2.3 Do not play around while the tool is being used to avoid the danger of distractions.
2.4 Do not work with the device in potentially explosive environments in which there are
inflammable liquids, gases or dusts. Electrical power tools create sparks, which can ignite dusts
or fumes.
2.5 Do not use the device if you are tired or under the influence of drugs, alcohol or medication.
3. When the devices are not being used, store them in a safe place.
4. Use a suitable device for the job will be safer at work and have a better result.
5. Always use a screwdriver that is intended for the task you are undertaking. Do not overload or use
it improperly such as drilling or tapping.
6. Dress properly. Do not wear loose clothing or jewels while operating the tool to avoid the danger of
trapping.
7. By using the device correctly, make sure to hold it firmly with two hands in place before starting
the trigger.
8. When using the electrical power tool, take into account the auxiliary handle or waist hook is
advantage of working conditions. On the contrary, the purposes of the waist hook or driver hook is
convenient to put the device away and easier to keep it out of reach of children.
9. Look after either the device or the battery carefully and have any damaged parts repaired by an
authorized or qualified shop. Always keep the tool nice and clean; pay attention on the machine
grease which might ruin the tool.
10. Disconnect the plug from the power source after the charger has been used.
11. Take apart the battery from the device when it is not being used.
12. Use only the accessories that are detailed in the operating instructions. The use of others which are
not recommended in the operating instructions may affect the functioning of the device. It could
lead to an increased risk of personal injury as well.
13. Remain alert at all times and watch what you are doing during proceeding. Before operation,
always check every part is in good condition and move freely in order to function properly.
14. This device only applies for metal screw bits designated with their dimensions and their shape. Do
not recommend to countersink or force of loading on any material such as plastic and wooden.


3
Forward / Reverse
15. The device does not apply for elastic or tensile load with washer on.
16. To prevent parts in gearbox from damage, replace the grease at least once for every year.
17. It is necessary for the operators to read and follow up all the operating instructions in this manual.
KILEWS is not responsible for any personal injury that might cause of disobeying the safety
advices.
Function of Cordless Protection
▉Over electric current protection
▉Prevent from low power
▉Thermal Protector
▉Stall protection
▉Slow rotation protection
▉Reverse control protection
▉Battery Identification
▉Sleeping mode
Warning
Do not attempt to repair or disassemble this cordless screwdriver, the warranty will be
considered void.
1. Make sure to remove the battery pack before maintaining or repairing the device by a qualified
technician.
2. Do not attempt to disassemble or reassemble the device at will which may result in poor
performance or danger of injury, the warranty applies only to initial package.
3. Do not repair the device with other than genuine KILEWS replacement parts may result in poor
performance or danger of injury, the warranty will be considered void.
4. The temperature between 0∘C ~35∘C would be an ideal condition of carrying out the tasks on the
device.
Operation Cautions
1. Charge the battery in the charging station before first use to make sure operates at its highest
capacity. To ensure operators against injuries, release the forward/reverse lever as arrow showing
below into a center position to have trigger locked before start or disassemble the device.


4
2.1. Below illustration is showing the process of correct install & disassemble the rechargeable battery.
The beep sound comes along with a flash while the screwdriver is supplied genuine battery
installation. It could be operated once the battery has been identified.
2.2. Too slow to install the battery may cause error identification so the beep sound and flash would be
continuing. In order to function properly, re-assembling it as below process again.
Insert battery steps
(1) Insert the rechargeable battery into the device follow by the arrow as showing.
(2) Assembled completely.
Remove Battery Steps
(1) Press the release button and (2) Follow the arrow direction. (3) Removed completely
take it out of the device.
Battery
Release
Button


5
(4)
(1)
(3)
(2)
(6)
(5)
(7)
(8)
Appearance Functions Introduction
Function Name Table
No.
Description
No.
Description
(1)
Start/Stop Switch
(5)
Tool Wristband
(2)
Forward/Brake/Reverse Switch
(6)
Belt Clip
(3)
Working LED Light
(7)
Tighten/Battery Status LED
(4)
Bit Holder
(8)
Torque Adjustment Button


6
Manual / Functions
1. Impact cordless screwdriver
Screws are continually fastened up while come along with clutch PA-PA-PA sound until the device
reaches Of Five control The Stop time.
(1) Trigger switch
The LED lights on when the trigger switch has been pressed about one-third down, and then the
screwdriver starts functioning when the switch trigger has been pressed half way down; on the
contrary, it stops when the screw has been tightened up or the trigger has been released.
(2) Forward/Reverse switch
When push the Forward/Backward switch to the right. According to the symbol on the switch,
the screwdriver rotates clockwise and tightens the screws. When push the switch to the
screwdriver will rotate anti clockwise and loosen the screw. When the screwdriver is idle, set the
Forward/Reverse switch in the middle.
Forward (screw) Reverse (unscrew)
(3) LED light
While press the trigger, the LED lights up automatically to assist the job to be done; on the contrary,
it will be off once the trigger has been released.
(4) Bit sleeve
Switch the screw bit and compatibility, pull the head of the type B screwdriver, and install the bit
according to the diagram below, after installing the bit please also install the Socket Extension Insert the
sleeve type and push it in following the arrow indicated on the diagram below on Diagram 2.
Diagram 1 Diagram 2
Insert the sleeve
Socket Extension
Pull the bit holder
Insert the bit into


7
(5) Tool wristband
Use wristband with tool for more convenient and safer operation and store.
(6) Belt Clip
Use belt clip to fix tool for more convenient and safer operation and carry.
(7) Buzzer beep and LED light indicating descriptions:
Operation status
LED Lights
Buzzer Beep
Voltage 17V~17.5V
Red light flashing continue
Beep continue
Voltage under 17V
Red light continue
2 short and 1 long Beep continue
Torque reached stop
Green light flashing 1 time
Beep 1 time
Over current protection
Red light flashing 6 times
Beep 6 times
Over temperture protection
Red light flashing 9 times
Beep 9 times
Low rpm protection
Red light flashing 3 times
Beep 3 times
Stall protection
Red light flashing 3 times
Beep 3 times
Battery ID error
Red/Green light flashing continue
Beep continue
(8) Torque Adjustment Button:Five sections Bit torque setting
1).Will Forward/Reverse Lever Cut to the middle position。
2).Pressing a bit start switch button at the Wake screwdriver。
3).Pressing Torque Adjustment Button Approximately 5 seconds, Torque identification light starts
flashing, then press the torque adjustment knob to adjust the desired torque.
4).Adjust the desired torque,Pressing Torque Adjustment Button Approximately 5 seconds., LED stops
flashing and at Approximately 5 seconds after the off, adjustment is completed.
5).Confirm torque, the reverse switching lever forward or reverse position cut positive and depresses
the start switch, view the lights is lit for the torque The selected lights.
6).left small print small the of torque to 0 ~ 20 N.m, the to more Choose on the right in
lights,Torque larger Until 5 lights,Large of Word characters 0 ~ 100 N.m.
2. Please pay attention when operating the rechargeable screwdriver. Do not drop or abuse the
screwdriver.
3. Not allow to turn the H/M/L switch during operation in order to cause system malt-function.
4. During operation, the Forward/Reverse switch has been changed accidentally that the device will
enable its self-protecting mode which is power off. Re-start the tool when this happen.
5. When switches Forward/Backward switch during the screwdriver still operating, the protection
mechanism will be triggered and cause the motor to stop. Restart the screwdriver again will change
back to normal.
6. Each operational torque setting, using time and frequency may result in different level of wear and
tear, at higher torque setting and use extensively could accelerate the wearing down of tool. After
one month, the torque is getting reduce gradually at the rate of 2~3% or 3~5 %( max torque). The
longer use of the device, torque reduction will become stable and the users could measure the torque
by a tester on a regular time schedule to check if the torque power still meets the criteria.


8
Other Cautions
1. The best condition of using the tool is under 8 hours a day, do not over loaded.
2. Do not attempt to repair or disassemble this cordless screwdriver without authorization. Always
have the device serviced by assigned factory or qualified person in order to have the warranty
effective continually.
3. KILEWS is not responsible for any poor performance or damage caused by customers own
modification of the tool.
4. It is necessary for the management to have individual operators read and follow up all instructions
in this manual. Do not attempt to repair or disassemble this cordless screwdriver themselves.
5. Removing protection cap by pry open the slots located on both side of the screwdriver as indicated
in the diagram 1 below. To install the protection cap, the cap gap facing downward and push it into
the slots. As indicated in the diagram 2 below.
6. The torque measuring of SKC-PTI-100 is completed by SKIDMORE-WILHELM model J bolt
tension calibrator.
Description of battery and charger
1. KILEWS SKC-LB1820B series of batteries as options to fit in the device; you may consult with local
agent based on your task requirement.
2. The use of other than genuine KILEWS batteries or screwdrivers can’t be active due to the build-in
protection system enforce no charging.
3. SKC-P80W-D charger with LED on is recommended.
Warring beep sound
1. Screwdriver stops along with three warring beep occurs while the motor speed is lower than 1000
rpm.
2. PCB temperature detector preventing the screwdriver overheated; it stops along with three warring
beep occurs while the PCB temperature is over 70℃.
3. Restarting the screwdriver which dismissing from a safety mood may come along with three beep
sounds.
Diagram 1
Diagram 2
Slots
Insert


9
Specifications
Bits Code ~ B: Hex 6.35mm
Accessory ~ＢＩＴ no.：NO.3# apply to 3.0~4.0mm
CAUTION
KEEP THESE INSTRUCTIONS
DO NOT DESTROY
MODEL
SKC-PTI-100B
Input Voltage
DC 18V
Bit torque(N.m)
1
0~20
2
0~40
3
0~60
4
0~80
5
0~100
Rev speed at no load
n0: (r/min) )±10%
0~2300
Impact rate (B.P.M)
0~3000
Weight (Kg)
1kg( battery not include )
Length (mm)
155 mm ＊195mm
（L＊H battery not include ）
Model of rechargeable battery
SKC-LB1820B
Model of battery charger
SKC-P80W-D
Bit type