King Tony Garage Series User manual

Garage Series
Warning: Excessive weight
hazard!
Use two or more people to move,
assemble, or install cabinets and locker
to avoid back injury.
Do not leave children unattended near
cabinets.
REV.00

INDEX
Tools Required/Hardwares Needed 1
Worktops/Weight Capacity 2
Installation options for Cabinets 3
Installing Leveling Feet (Optional Accessory) 4
Installing Pillars 5
Installing Hanging Panels 6
Attaching Cabinets together 7
Attaching Cabinets together/Removing Drawers 8
Mouting the Woktop 9
Attaching Pillars together 10
Installing Wall Cabinet 11
Installing Corner Wall Cabinet 12

Tools Required
Hardwares Needed
Hex Bolt
(M6x16)
Nut
(M6) Plastic Pin Hex Bolt
(M8x16)
Washer
(D8)
Spring Washer
(D8)
Wood Screw
(ST6x16)
Sunk Screw
(M6x16)
Pencil
Tape Measure
Magnetic Leveler
Phillips Bit
socket
Cordless Power Drill
Adjustable wrench
Socket driver
wrench
Masonry Bit
Phillips head
screw driver
Set Square
1
1 2 3
2
3
1

30Kg
15Kg
10Kg
30Kg 30Kg
30Kg
30Kg
30Kg
30Kg
30Kg
30Kg
Worktops
26" Worktop. Fits over 1 Cabinet 53" Worktop. Fits over 2 Cabinets
80" Worktop. Fits over 3 Cabinets
Corner Worktop
Weight Capacity
Double-door Locker
Max 300Kg
Single-door Locker
Max 180Kg
Wall Cabinet
Max 15Kg
Hanging Panel
Max 10Kg
Base Cabinet
Max 60Kg Drawer Cabinet
Max 150Kg
Trash Bin Cabinet
Max 90Kg
50Kg
50Kg
50Kg
50Kg
50Kg
50Kg
30Kg
30Kg
30Kg
30Kg
30Kg
30Kg
30Kg
2

Installation options for Cabinets
Important information: Please read
before beginning installation.
Layouts shown are only examples.
Based on customer's purchase,
cabinets can be configured in a
varietyof different layouts.
Consider the location of electrical
outlets when planning layout.
•
•
3

Installing Optional accessory
Begin by attaching the leveling feet (optional accessory).
Please skip and turn to Page 5 if no leveling feet are purchased.
4

Installing Pillars
Hardwares Needed.
Rivet Nut
For Locker and
Support Bracket
Hex Bolt
(M6x16)
Nut
(M6)
5

Installing Hanging Panels
Hardwares Needed.
Hex Bolt
(M6x16)
Nut
(M6)
6

Attaching Cabinets together
Hardwares Needed.
Position and secure remaining cabinets to wall. Install cabinets one at a time.
Please adjust four leveling feet to make sure it's even to the ground.
Attach Locker and Base Cabinet
Attach Drawer and Base Cabinets
Attach Corner and Base Cabinets Attach Base Cabinet and Support Brackets
Attach Sink and Base Cabinets
Rivet Nut
Hex Bolt
(M6x16)
Nut
(M6)
7

Attaching Cabinets together
Removing Drawers
Attach Base Cabinet and Work Bench
Press the drawer's side parts as shown
simultaneously to remove the drawers.
Left Side Right Side
8

Mouting the Woktop
Hardwares Needed.
On the Cabinet On the Support Bracket
5
Hex Bolt
(M6x16)
Wood Screw
(ST6x16)
9

Attaching Pillars together
Hardwares Needed.
Hex Bolt
(M6x16)
Nut
(M6)
No need to fasten
in the corner.
10

Installing Wall Cabinet
Hardwares Needed.
Hex Bolt
(M8x16)
Washer
(D8)
Spring Washer
(D8)
Hex Bolt
(M6x16)
Nut
(M6)
Pre-assemble the Bolt
and washer on the Panel
Hang on the Wall
Cabinet and fasten
the bolt.
NOTE: This step is for 3 types of wall cabinet.
11

Installing Corner Wall Cabinet
Hardwares Needed.
Hex Bolt
(M8x16)
Washer
(D8)
Spring Washer
(D8)
Sunk Screw
(M6x16)
12