KINGSIGNAL MT1 User manual

Registered trademark of KINGSINAL. All trademarks mentioned in this manual are
owned by their respective owners.
The product specifications and information mentioned in this manual are for reference only and
are subject to change without prior notice. Unless otherwise agreed, this manual is only used as
a guide, and the statements made do not constitute any form of warranty.
Address: 23-27 / F, block B, building 10, No. 1819, Shahe West Road, Nanshan District, Shenzhen,
China
Company website: http://www.kingsignal.cn
Technical support hotline: [phone]

Product appearance（1.2）
1. System LED
Green Light On —The connection between the main route and the node is normal and can be
connected to the Internet.
Blue Light Flashing —Mesh device is searching.
Red Light On —Normal connection, weak signal from slave node.
Red Light Flashing —There is no Internet connection or the slave node cannot connect to the
main route.
2. Port
POWER —Used to connect matching power adapters.
LAN —Used for connecting computer, set-top box and other wired equipment.
WAN —It is used to connect broadband Modem or block.
RESET —For restoring router to factory Settings, see FAQ for details.
Bill of materials: ·three gigabit wireless routers ·a quick installation guide.

Schematic of hardware connection（3.4）
POWER：Used to connect matching power adapters.
WAN：Used for connecting broadband interfaces such as broadband Modem or cell.
LAN：Used for connecting computer, set-top box and other wired equipment.

Set router for the first time after boot（5.6）
Set management instructions through APP
1. Connect router to factory default wireless name with mobile phone.
2. After the connection is successful, turn on the mobile phone "Elven Guest" APP and
automatically jump to the management interface; Create administrator password, click save.
3. After selecting a good time zone, click Save.
4. Manual choice of Internet access, please set the Internet access parameters according to the
actual situation. Click Save to complete the setup. The router can be used normally.
5. After entering the management password, you can open the router management interface.
Set router for the first time after boot（7.8）
Set management instructions through web
1. Connect the router with the computer / mobile phone. The default wireless name.
2. After the connection is successful, login to the management interface, create an
administrator password, and click "Next."
3. After choosing a good time zone, click next.
4. Manual choice of Internet access, please set the Internet access parameters according to the
actual situation. Click Save to complete the setup. The router can be used normally.
5. After entering the management password, you can open the router management interface.

Frequently Asked Questions（9）
Why the login page does not appear after entering the URL Http://192.168.6.1.
·Make sure the computer is set to get IP automatically.
·Make sure the browser tries to enter Http://192.168.6.1.
·Try using another browser
·Restart the router and try again.
What if there's no Internet?
·Please check that the computer is connected to Modm using a network line. If not, please
contact your network service provider.
·Login Http://192.168.6.1 again login settings
Restart the router and try again
How do I restore the router factory settings?
·When the router is running, press the "RESET" button on the back of the router for 5 seconds
until the red light starts flashing.
I forgot. What about the router code?
·Refer to "How do I restore router factory settings" to restore factory settings and log in
according to the SSID and default password on the back of the router.
I forgot my wireless code.
Login to the router's APP or web management interface, "Settings"-
` Wireless Settings "click"
Routers, red lights. What about Changliang?
·If it is the main route, make sure that the network connection is loose, the router is connected
to the Internet, or call the broadband operator to confirm whether the network is normal. If you
are a subroute, adjust the router's position and retrigger the pairing.

·Try rewiring the router or restoring factory settings
Cell phones, tablets, laptops, no Internet access?
·Make sure your device's wireless function is in normal condition. If the wireless switch is on, you
can search for wireless signals.
·Please make sure that the wireless router settings are correct. Please do not use Chinese or
special characters for wireless names.
·Please make sure you fill in the wireless password correctly.
Product warranty card（10）
Dear user, Hello!
Welcome to KINGSIGNAL products. To protect your rights and interests, please read the following
carefully after purchasing the machine:
The following are not covered by free maintenance. The company can provide paid services.
Please note:
1. The warranty period has been exceeded.
2. Failure to install, use, store, or maintain the product as required by the instructions resulted in
product failure or damage.
3. Modify and tear the bar code.
4. Unauthorized changes to the inherent setting documents and unauthorized demolition
machine maintenance.
5. Accidents lead to good and bad, such as inappropriate voltage input, water intake, mechanical
damage, fall, etc..
6. Damage caused by transportation, loading and unloading during product repair.
7. Product failure or damage caused by irresistible forces such as earthquakes, fires, floods,
lightning strikes, etc..
Second, KINGSIGNAL product after-sales service promise: one-year warranty.
Special note:
1. The external power supply warranty period is 1 year. If the power adapter has obvious hard
damage, cracks, severe deformation, and damage to the power cord due to improper use or
accidental factors by the user, the user can not replace it.
2. Warranty warranty is limited to the host, packaging and accessories are not covered by the
warranty.
3. If there are equipment performance problems within 15 days after the purchase of the product
and there is no damage to the appearance, you can directly replace the new product. During the
free warranty period, the product was tested by Jinxinnuo. After confirming the failure, the same
type of reconstructive product will be replaced. The replaced defective product will be owned by
Jinxin Nuo Company; For faultless products, it will be returned.
4. When performing warranty or warranty service, please bring the corresponding invoice. If you
can not produce the purchase certificate, the free warranty period of the product starts from the
date of production.
5. The mailing cost of the returned product is paid by the sender in one way.
Within the scope of national laws and regulations, the power of interpretation and amendment
of this promise shall be vested in Jinxinuo Company.

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Caution:
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems.