Kiramek Vision 1460H Series User manual

© 2020 KIRAMEK, INC., Aichi Japan
Ver. 1.6, JUN.2020
FACTORY KEYLESS UPGRADE SECURITY
1460H / H+
series

Thank you for purchasing this VISION
1460H series Vehicle Security System.
The 1460 is a state of the art device that
will provide you with years of trouble
free service if used properly. Please fa-
miliarize yourself with the content of this
Owner’s Guide to get the most out of
your new system. We trust you will enjoy
using the product.

© 2020 KIRAMEK, INC.
NOTICE! Although reasonable efforts have been taken to ensure accuracy in this
Owner’s Guide, Kiramek Inc. shall not be held liable for any errors, omissions, prop-
erty damage, or injury resulting from the use of this information.
All product specifications and features are subject to change without notice.
TA B L E OF CO N T E N T S
Limited Lifetime Warranty ................................... 1
Included Items ............................................ 2
Arming & Disarming ....................................... 3
Arming ................................................ 3
Confirmation Chirps .................................... 3
Disarming ............................................. 4
Manual Disarming ...................................... 5
Main Features ............................................ 6
Trunk Release Bypass .................................... 6
Door Trigger ........................................... 6
2-Stage Shock Sensor ................................... 6
Ignition Trigger ......................................... 7
(+)12v Trigger .......................................... 8
Error Chirp ............................................. 8
GWA (Ground When Armed) ............................. 8
SBS (Sector Bypass System) ............................... 8
Status LED (Trigger Memory) .............................. 9
Light Flash ............................................ 10
Resume .............................................. 10
Valet Mode........................................... 10
Programmable Features ................................... 11
Reset to Factory Defaults ............................... 13
Troubleshooting .......................................... 14
Options ................................................. 16

1
© 2020 KIRAMEK, INC.
Limited Lifetime Warranty
The VISION 1460 Control Module is backed by a limited lifetime war-
ranty against defective components and/or improper product assembly
to the original purchaser for as long the vehicle is owned by that same
purchaser, contingent upon installation by an Authorized VISION Deal-
er. All product warranties become void if the VISION 1460 system was
not sold and installed by an Authorized VISION Dealer or the system
is moved to another vehicle. All other parts and/or accessories that
connect to VISION 1460 systems, including but not limited to the Shock
Sensor (1460H+) and LED Program Switch, are warranted for one (1)
year from the original date of purchase.
During the warranty period, Kiramek Inc. will repair or replace, at its
sole discretion, any system component that is found defective in mate-
rial or assembly during the warranty period, provided that the product
is returned to Kiramek Inc. by an Authorized VISION Dealer and is ac-
companied by a clear and legible copy of the original purchaser’s receipt.
Any damage to your VISION 1460 system that results from normal
wear-and-tear, accidents, improper use, neglect, faulty wiring, incorrect
installation, modication, removal or defacement of the product serial
number, alteration or repair outside Kiramek Inc or its Authorized VI-
SION Dealers immediately voids this warranty.
This warranty is limited to defective parts only and does not provide
any compensation whatsoever for damages associated with the VISION
1460 system or its accessories. This warranty does not cover installa-
tion labor, product removal and/or reinstallation fees. This warranty
is valid for the original purchaser only and may not be transferred to
another party. Kiramek Inc makes no warranty against theft or vandal-
ism of the vehicle in which the VISION 1460 system was installed. This
warranty shall not be interpreted as an insurance policy against loss,
nor shall Kiramek Inc be liable any in way for such loss, nancial or
otherwise.
WARNING! DO NOT ATTEMPT TO INSTALL THIS VISION 1460 PRODUCT YOUR-
SELF BECAUSE SUCH WILL IMMEDIATELY VOID THE WARRANTY. THIS SECU-
RITY SYSTEM MUST BE PROFESSIONALLY INSTALLED BY YOUR AUTHORIZED
VISION DEALER TO VALIDATE YOUR WARRANTY.
KIRAMEK may opt to validate the above Warranty, in writing, for shipments outside Ja-
pan, in cases where there is no local VISION Dealer available to perform the install.

2
VISION 1460H/H+ OWNER’S GUIDE
INCLUDED ITEMS
LED Program Switch Parts
Status LED
Program Switch
Control Module (1pc) Shock Sensor (1pc) LED Program Sw. (1pc)
Sensor Harness (1pc)
Sensor Tape (1pc) Window Decals (2pc) Guides (2pc)
VISION
IR SHOCK SENSOR
25cm Wire Ties (2pcs)
FACTORY KEYLESS UPGRADE SECURITY
1460
DIGILINK
∞
SMART
FACTORY KEYLESS UPGRADE SECURITY
1460
series
DIGILINK
∞
SMART
Control Mod. Harnesses (3pcs)
Main
Harness
1460H+ only

VISION 1460H/H+ OWNER’S GUIDE
3
Arming & disarming
ARMING
CONFIRMATION CHIRPS
NORMAL ARMING
Close all doors and then LOCK by your factory
keyless remote or by SmartKey door handle
touch. Hazard lights will ash, doors will lock, and
the Horn will chirp 1 time (if Conrmation Chirps are
ON). The Status LED will light for 5s, during which
time all triggers are disabled. Then the Status LED
will start ashing and Ignition, Door, Trunk and Hood
triggers become enabled. The Shock Sensor (1460H+ only) is enabled 5s
after the LED starts ashing (10s after you Lock).
SENSOR BYPASS ARMING
This procedure lets you temporarily disable
the Shock Sensor for a single Arming session:
1) With Ignition OFF, press the Program Switch twice.
2) Within 20s, press LOCK on the factory remote to Arm.
The system is now Armed in Sensor Bypass Mode, and all triggers are active
except the shock sensor (1460H+) and other external sensors. Note that when
you Disarm and then Arm again normally, the shock sensor will be enabled.
(ON by default)
This procedure lets you enable or disable the
Arm/Disarm chirps. (Note that the Horn
will still honk when the 1460 is triggered.)
1) With Ignition OFF, press the Program Switch once.
2) Within 20s, press LOCK on the factory remote to Arm.
The conrmation chirp state has now toggled and the system is Armed. Re-
peat the above procedure to toggle the conrmation chirp state back again.
PROGRAMMABLE
OFF
OFF
LOCK
2 Pushes
1 Push

© 2020 KIRAMEK, INC.
4
arming & disarming
DISARMING
NORMAL DISARMING
UNLOCK by your factory keyless remote or by
SmartKey door handle touch. Vehicle hazard
lights will then ash, doors will unlock, the Horn
will chirp 3 times (if Conrmation Chirps are ON),
and the Status LED will turn off. The 1460 is now
Disarmed and you may enter the vehicle.
If the Horn chirps 4 times when you Disarm, it means something had trig-
gered while you were away from the vehicle. In this case, the Status LED
will ash to tell you what caused the trigger (see Trigger Memory, page 9).
Some vehicles equipped with remote engine starters do not allow you to
Unlock while the engine is running. In such a case, you will not be able
to Disarm the 1460 until you shut off the engine.
REMOTE STARTER NOTE
Programmable Feature No.2 prevents Relay Attacks by requiring 2
presses of Unlock on the factory remote to Disarm. See pages 11~12.
THWART RELAY ATTACKS
You cannot Disarm simply by pressing UNLOCK in cases where the
1460’s Horn was triggered by the opening of a door or the trunk or the
hood or the Ignition ON. You must follow the above 4-step procedure!
IMPORTANT!
DISARMING AFTER A DOOR/HOOD/TRUNK/IGNITION TRIGGER
If the Horn is triggered by the opening of a Door or the back hatch
(Trunk) or the Hood or by the Ignition being switched ON, you
must perform the following procedure to Disarm:
1) UNLOCK with factory keyless (with doors/hood/trunk closed).
2) Open the driver’s side door, enter the car, then close the door.
(The Horn will honk when you do this, if it is not already honking.)
3) Ensure the Ignition is OFF, then switch the Ignition ON then OFF.
4) UNLOCK again with factory keyless. The system should Disarm.
Shock Sensor Triggered or Nothing Triggered.
UNLOCK

5
© 2020 KIRAMEK, INC.
arming & disarming
MANUAL DISARMING
You can manually Disarm using a secure code in the event your
factory remote’s battery dies (see Note 2 below). The factory
code is “6”, but you can change this code to another number of
your choosing for greater security (see the bottom of this page).
1) Enter the car. (The Horn will honk. You can leave the door open or closed.)
2) Turn ON the Ignition.
3) Within 30s, press the Program Switch the same number of times as
your Disarm Code. (Factory Default Code = 6)
4) Turn OFF the Ignition. (The 1460 should Disarm and the horn should
stop.)
1) If the 1460 won’t Disarm in Step-4 above, you entered the code incor-
rectly. Start over from Step-2.
2) Many Push Start cars don’t allow the Ignition to be switched on in
the absence of the Factory Remote. So if you lose or destroy your car’s
remote, you may not be able to Manually Disarm the 1460. But if your
factory remote merely has a dead battery, you will be able to switch on
the Ignition and Manually Disarm using the 4 steps above.
NOTES
MANUAL DISARM CODE MODIFICATION
The factory code is “6” but you should change it to another number between 1 & 30:
1) With the 1460 Disarmed, switch ON the Ignition.
2) Press the Program Switch for 6s, until the Horn chirps 3 times.
3) Release the Program Switch after you hear the 3 chirps, then turn OFF
the Ignition. The Status LED will light for 5s.
4) Quickly switch ON the Ignition again (while the LED is lit for 5s).
5) When the LED turns off, wait about 5s and you will see the LED start to
ash. Take note of the ashes as the number of ashes will be the num-
ber of your Disarm Code. Turn OFF the Ignition to program your code.
The LED will then ash the same number of times as your Disarm Code.
If you added any optional VISION transmitters, you must relearn them.
PROGRAMMABLE

6
VISION 1460H/H+ OWNER’S GUIDE
MAIN FEATURES
Some cars don’t support the automatic trigger bypass feature of the
1460. In that case you will need to rst Unlock/Disarm before you can
use your factory Trunk Release feature (otherwise the Horn will trigger).
NOTE
If you have a Trunk Release button on your
factory remote, pressing it while the 1460 is
Armed will bypass the doors/trunk for 5 sec-
onds. The Shock Sensor will be bypassed until you
close the trunk. The Ignition switch is never by-
passed. Five(5) seconds after you close the trunk,
the shock sensor will be automatically re-activated.
TRUNK RELEASE BYPASS
The Horn will honk for 30s when any door is opened
while the system is Armed. Vehicle hazard lights may
also ash. See bottom half of page 4 on how to Disarm
in this case. Also see Table-1, pg.9.
2-STAGE SHOCK SENSOR
1st Stage (“Warning Chirps”). Each time the Shock
Sensor detects a light impact to the vehicle body, the
Horn will chirp 5 times. The Shock Sensor will not trig-
ger the Horn while in Sensor Bypass Mode.
2nd Stage (“Full Trigger”). When the Shock Sensor de-
tects a hard impact to the vehicle body, the Horn will
honk for 30s (or until Disarmed with the factory remote).
The Shock Sensor will not trigger the Horn while in Sen-
sor Bypass Mode. Also see Table-1, pg.9.
See page 15 for common shock sensor problems and solutions.
5 Chirps
30s Blast
The Horn will honk for 30s when the trunk is opened
(without the remote) while the system is Armed. Ve-
hicle parking lights may also ash. See bottom half of
pg.4 on Disarming in this case. Also see Table-1, pg.9.
TRUNK TRIGGER
DOOR TRIGGER
TRUNK
1460H+ only

7
© 2020 KIRAMEK, INC.
main features
IGNITION TRIGGER
IG PROTECT MODE (default)
The Horn will honk for 30 seconds when the
Ignition (IG) is switched ON while the system
is Armed. Vehicle parking lights may ash. See bottom half of page 4 on
how to Disarm in this case. Also see Table-1, pg.9.
REMOTE START COMPATIBILITY MODE (RSCM) (user-programmable)
When the Ignition switches ON while Armed in
this mode, the Horn will not trigger. Instead,
Shock Sensor (1460H+) and Ignition triggers are
bypassed, while Door, Hood & Trunk triggers re-
main active. This allows 3rd party remote starters
to start the engine without triggering the Horn. The vehicle is still pro-
tected though, and any attempt to open a door or the trunk will trigger the
Horn**. And when the remote starter stops the engine (i.e., Ignition turns
off), Sensor and Ignition triggers are automatically re-activated.
IIP (Intelligent Ignition Protect)
IIP activates when you enable RSCM. The purpose of IIP is to tem-
porarily switch back to IG Protect Mode after a Horn trigger.
Purpose. Most “remote start compatible” car alarms bypass all trigger
inputs after the Ignition is switched ON. So if a thief opens a door the
Horn will trigger; but the thief can then close the door, turn on the Igni-
tion, wait until the Horn stops, then drive away in silence because the
Ignition-ON state prevents the Horn from triggering again! Yet other
car alarms that always trigger the Horn when the Ignition turns ON
offer no remote start compatibility at all. IIP solves this problem by
offering compatibility with Remote Start, with complete security.
How it works. Normally, if the Ignition is turned ON while in RSCM,
the system automatically bypasses the Sensor & Ignition triggers but
keeps Door, Hood and Trunk triggers active. But if the 1460 is triggered
by a Door before the Ignition is turned ON**, IIP automatically switches
back to IG Protect Mode, and the Horn will be triggered if the Ignition
is turned on. Disarming and Arming again will revert to RSCM.
**Door-open response depends on the setting of Feature No.6, described on pages 11-12.
PROGRAMMABLE
IG ON
IG ON
L
O
C
K
A
C
C
O
N
S
T
A
R
T
START
STOP

8
VISION 1460H/H+ OWNER’S GUIDE
main features
GWA (Ground When Armed)
The 1460 feeds a (–) Ground output while the system is Armed.
Optional devices can be activated by this control line, such as
a Starter Kill Immobilizer Relay or LED scanners. When the
system is Disarmed, GWA is switched OFF and all attached devices turn
off. See the Installation Guide for electrical specications.
A “sector” is the Ignition, Hood, any Door, or attached Sensors.
When a sector triggers the Horn a certain number of times (see
below), that sector is bypassed (disabled) until you Disarm and
Arm again. This limits noise pollution caused by multiple Horn
triggers in a short period of time (such as when you park near
construction sites or if animals jump on the vehicle repeatedly).
DOOR/TRUNK/HOOD — If left OPEN, the Horn blasts up to 5 times
(30s each time), then the Doors/Trunk/Hood are bypassed until closed. (The
(+)12v Trigger WHT/BLK input is bypassed after triggering 10 times).
IGNITION — If the Ignition is left ON, the Horn blasts up to 10 times (30s
each time) and then the Ignition is bypassed until you Disarm & Arm again.
SENSOR — Warning triggers (5 chirps) and Full Triggers (30s of Horn
Honking) are independently bypassed after 10 times. You must Disarm
and then Arm again to re-activate. (1460H+ only)
SBS (Sector Bypass System)
HOOD TRIGGER
On compatible vehicles (or on any vehicle when the op-
tional analog Hood input is connected), the Horn will
honk for 30 seconds when the hood is opened while
Armed. See bottom half of page 4 on how to Disarm.
ERROR CHIRP
If a Door or the Hood or Trunk is open when you Lock/Arm, you will hear
1 chirp (if Conrmation Chirps are enabled) followed by 2 chirps (even if
Conrmation Chirps are disabled). The 2 chirps are Error Chirps that noti-
fy you the doors/trunk/hood will be bypassed (they won’t trigger the Horn)
because they are open. But 5s after you close the door/trunk/hood, they
will then trigger the Horn if later opened. You will only hear Error Chirps
on cars that allow Lock/Unlock when the doors/trunk/hood are open.
OFF

VISION 1460H/H+ OWNER’S GUIDE
9
main features
The Status LED ashes slowly about once per second while the system is
Armed, acting as a visual theft deterrent. The LED turns off when the
system is Disarmed, unless there was a Horn trigger.
TRIGGER MEMORY
The LED ashes rapidly while the full 30s Horn blast is going off
and keeps ashing rapidly even after the Horn stops. When you
Disarm, the Status LED will change its ashing pattern according
to Table-1 below, showing you what triggered the Horn.
If the Horn triggered more than once, the LED will show you what caused
the last 3 triggers. Trigger Memory will displayed repeatedly on the LED
until the Ignition is switched ON or until you Arm again.
STATUS LED
TABLE-1 Status LED Trigger Memory
LED Flashes What Triggered the Horn
2Door or Trunk (or Hood)
3(+)12v Trigger (see NOTE below)
6Ignition
7Sensor (Full Trigger only)
There are no LED Flashes if the power is cut and then restored.
Three (3) ashes are reported on the Status LED only if the 1460’s
WHT/BLK (+)12v Trigger input is connected. This is optional connec-
tion behaves exactly like the (–) Door/Trunk/Hood trigger input, but
the polarity is (+) postive instead of (–) negative. It’s used in cases where
you wish to connect to a “(+) positive controlled” switch or device in the
car that you want to trigger the 1460’s Horn (while Armed).
Also note that if the optional TR537S Paging System is installed,
(+)12v triggers on the WHT/BLK wire (while Armed) will cause the
Pager’s “Trunk” icon to ash, even if you’ve connected to something
other than the trunk.
(+)12v Trigger NOTE

© 2020 KIRAMEK, INC.
10
Valet mode shuts down all functions of the security system, ensuring the
Horn will never trigger. Valet Mode is useful when you must hand over
your car keys to a valet or car maintenance technician, so there is no worry
they will trigger the Horn by accident.
Activation: With the Ignition switched OFF and the 1460
Disarmed, press and hold the Program Switch for more
than 6s, until the Status LED turns OFF. (When the LED
turns OFF, release the Program Switch.)
Deactivation: Press and hold the Program Switch again
for 6s, until the LED turns OFF. Security features are now restored. (You may
hear 2 quick chirps the rst time you Arm, to inform you that you have just exited
Valet Mode.)
main features
LIGHT FLASH
When so installed, vehicle Parking lights will ash continuously for the
entire 30s duration of full Horn triggers, and will ash 5 times when shock
sensor Warning Chirps are triggered. But note that some cars do not sup-
port Parking light ash unless an optional relay is installed.
When you activate Valet Mode, the Status LED will not blink and you
will not receive any indication of being in Valet Mode. The security
system will be completely turned off. This also means that someone
could break into your car. Our company accepts no liability whatsoever
if your car is stolen or vandalized or its contents stolen due to your hav-
ing entered Valet Mode. You use this feature at your own security risk.
CAUTION!
Valet Mode PROGRAMMABLE
RESUME
RESUME is a form of State Memory that remembers if the system was
Armed or Disarmed when the main power is cut. When power is restored,
the 1460 will power-up Disarmed if it was disarmed in its previous state.
If originally Armed, it will power-up Armed and with the Horn honking.
Push 6s

11
© 2020 KIRAMEK, INC.
11
PROGRAMMABLE FEATURES
You can change some features of the 1460 by using the Program
Switch. Perform the following 4-step procedure to change the fea-
tures shown in Table-2:
1. Start the engine and then Stop the engine. (Only required for Hybrid cars.)
2. With the Ignition OFF, Arm the 1460 and then immediately Disarm.
3. Within 20s, turn ON the Ignition.
4. Press the Program Switch the same number of times as the feature you
want to program — refer to the “No.” column in Table-2 below. (For
example, to change “Auto Arm,” push the Program Switch 8 times.)
5. Turn OFF the Ignition.
TABLE-2 Feature Selection Menu
No. Feature Description Toggle Settings
2 Require 2 Unlocks to Disarm OFF ON
3 Ignition Trigger IG Protect RSCM
4 Safety Lights During Remote Start OFF ON
5 Error Chirp ON OFF
6 Ignore Factory Unlock (Disarm) Signal NO YES
7 Safety Lights: Flashing or Solid-ON Solid-ON Flashing
8 Auto Arm OFF ON
9 Horn (Pulsed) or Siren (Continuous) Output Pulsed Continuous
10 Auto Rearm OFF ON
17 Exterior Illumination OFF ON
FACTORY DEFAULT SETTINGS SHOWN IN BOLD TEXT ABOVE
1) After you complete Step-5 above, the Status LED will ash the same
number of times as the feature you just programmed. Because the set-
tings merely “toggle,” there will not be any indication of the “Toggle
Setting” you just programmed. Test your 1460 system to conrm your
programmed settings. To program another setting, repeat the steps.
2) To Reset to Factory Defaults, see method on page 14.
NOTES

12
VISION 1460H/H+ OWNER’S GUIDE
programmable features
When set to ON, and when the system is Armed, parking lights will illu-
minate for safety while the Ignition is turned on by a remote start system.
(This feature only works if program the Ignition Trigger to RSCM.)
4Safety Lights During Remote Start
When set to IG Protect Mode (default), the system will trigger the Horn
when the Ignition (IG) turns ON while Armed, as described on page 7.
When set to RSCM (Remote Start Compatibility Mode), the system will by-
pass the Shock Sensor (1460H+) and Ignition triggers when the Ignition
turns ON while Armed, as described on page 7.
3Ignition Trigger
You cannot Arm if IG is ON
2Require 2 Unlocks to Disarm
OFF by default. Set to ON to stop Keyless Relay Attacks*. When ON, press-
ing Unlock only 1 time will NOT Disarm. To Disarm you must press Un-
lock 2 times on your factory remote within 3 seconds. This prevents
Relay Attacks. Even if a Relay Attack thief touches the outside door handle
many times, only one Unlock signal is sent. Unlike the door handle, your
factory remote sends a signal each time you press Unlock on the remote.
So pressing 2 times on your outside door handle to Unlock will NOT Dis-
arm the 1460. You must press Unlock twice on your factory remote.
If you program Feature No.2 to be ON, you then cannot program Feature
No.6 to be ON. Conversely, if you have Feature No.6 programmed to be
ON, you cannot program Feature No.2 to be ON until you turn OFF Fea-
ture No.6. *Relay Attack Info: http://bit.ly/21TuqCF
If your car has wireless keyless entry (pressing Lock/Unlock on your factory
key locks/unlocks doors) but does NOT allow you to Lock/Unlock by merely
touching the outside door handle, Relay Attacks are impossible on your car
and therefore you can leave Feature No.2 set to OFF.
NOTE

VISION 1460H/H+ OWNER’S GUIDE
13
13
programmable features
9Horn or Siren Output
When set to Pulsed (default), the system will feed a pulsed (–)GND (3A
max.) output to honk the vehicle’s Horn. (Connect to the Horn relay.)
When set to Continuous , the system will feed a continuous (–)GND (1A
avg.) output to sound an optional siren for 30s (Full Trigger).
This feature automatically Arms the system when you do the following:
(1) turn Ignition ON & OFF then (2) Open & Close any Door. Upon seeing
these events, the system will Arm 20s after the last door is closed. The
doors will NOT be locked so you won’t be locked out if you leave your keys
in the car, but the system will be Armed and will trigger if a door is opened.
8Auto Arm
7Safety Lights: Flashing or Solid-ON
When set to Flashing, vehicle parking lights will ash for safety while a 3rd
party remote start system is active (remotely running the engine). And
when left set to the factory default of Solid-ON, parking lights illuminate
continuous (without ashing) when the remote starter is active.
ON by default. See Error Chirp description on page 8. When set to OFF,
any open doors/hood/trunk when you Arm will still be bypassed but you
will not hear the Error Chirp sound anymore — useful for some cars with
automatic sliding doors that take time to close.
5Error Chirp
6Ignore Factory Unlock (Disarm) Signal
Set to YES to prevent Keyless Relay Attacks* by not Disarming when you
press Unlock. (Ignores BLU/YEL Door Unlock input.) After you Unlock and
open a door you will have 20s to Disarm, either Manually (pg.5) or with
an optional remote, otherwise the Horn will honk. NOTE: Feature No.2
is more convenient (see pg.12) if your vehicle can produce 2 unlock pulses.

© 2020 KIRAMEK, INC.
14
This feature automatically Rearms the system 60s after it is Disarmed,
unless a Door is opened or the Ignition goes ON during the 60s. Doors will
be locked when the system Rearms.
10 Auto Rearm
If set to ON , when you Disarm, vehicle parking lights will illuminate for
30s or until a Door is opened or until the Ignition is switched ON, in order
to illuminate the area around the vehicle for greater visibility and security.
NOTE: Exterior Illumination behavior depends on the setting of Feature
No. 7, Safety Lights: Flashing or Solid-ON.
17 Exterior Illumination
Consult the manual that came with your transmitter (2-way pager or 1-way
3-button remote) to learn how to reprogram them. Also note that RESET
will restore the Manual Disarm Code to “6” (factory default).
NOTE
RESET Programmable Features to Factory Defaults.
NOTE#1: You must reprogram all your optional transmitters after Reset.
NOTE#2: You must know where the 1460 control module is located to Reset.
1. Disarm and ensure Ignition is OFF.
2. Disconnect the 1460’s main harness. (White connector with 6 thick wires.)
3. Push-and-hold the Program Switch.
4. Reconnect the 1460’s main harness. NOTE: The Horn will honk.
5. Release the Program Switch. NOTE: The Horn will stop, LED turns On.
6. Switch ON the Ignition. NOTE: Horn will chirp 3 times, LED turns Off.
7. Switch OFF the Ignition. NOTE: LED will light 5s, then ash 6 times
(Manual Disarm Code resets to 6). RESET complete.
programmable features

15
© 2020 KIRAMEK, INC.
TROUBLESHOOTING
FACTORY KEYLESS REMOTE WAS LOST, DISARMING
If the factory remote was lost, you may not be able to Disarm if you have
a Push Start car that requires the factory remote to turn on the Ignition.
In such a case, you must to contact your dealer for a replacement factory
remote. But if you have an older turn-to-crank style Ignition, you can
Disarm the 1460 by Manual Disarming, as described on page 5.
SOMETIMES CAN’T ARM/DISARM WITH THE FACTORY REMOTE
• On some cars, if you rapidly press Lock and Unlock on the factory re-
mote, the 1460 may stop responding to the remote. In this case the x
is simple — just wait longer between Lock and Unlock presses.
• If Conrmation Chirps (pg.3) are enabled, did you hear a single Horn
chip when you tried to Arm? If not, the Ignition may be ON. You can-
not Arm the system while the Ignition is ON (see “Ignition Trigger”
atop page 12), unless you have an optional TR537S or TR365 remote.
• You cannot Unlock to Disarm with feature No.6 set to ON. See pg. 11.
THE SYSTEM IS DEFINITELY ARMED, BUT IT WON’T TRIGGER THE HORN!
• It may be in Valet Mode. See page 10.
• It may be in Sensor Bypass Mode. See page 3.
HORN HONKS WHEN THE TRUNK IS OPENED
• You cannot open the trunk with the key or the Horn will honk. Use
your factory remote. If your keyless remote doesn’t have a trunk open
feature, then you need to Disarm the system rst (Unlock button on
your factory remote) and then open the trunk.
• If you open the trunk with your factory remote and the Horn triggers,
it could be the trunk release timing is too long. After pressing Trunk
Release on your factory remote, the trunk must open within 5s or the
Horn will sound.
• Some cars simply have a trunk release feature that is incompatible
with the 1460. In this case, rst Unlock/Disarm, then open the trunk.
I HAVE PROBLEMS WHEN MY TURBO TIMER IS USED
The 1460 is incompatible with all Turbo Timers. Only Remote Starters
are supported (see pages 7 & 11-12).
CANNOT DISARM WHILE THE HORN IS HONKING
• You must follow the 4-step procedure “DISARMING AFTER A DOOR/
HOOD/TRUNK/IGNITION TRIGGER” on page 4.
• Your factory remote’s battery may be dead. Use Manual Disarming (p5).

16
VISION 1460H/H+ OWNER’S GUIDE
SHOCK SENSOR 1st STAGE “WARNING” TRIGGER DOESN’T WORK
Examine the shock sensor and look closely at the two LEDs.
When you lightly tap on the sensor, do you ever see a Green LED light?
• If you never see Green light, adjust the sensitivity knob on the sensor.
• If after increasing sensitivity you still don’t see the Green LED, it
could be that the suspended element inside the sensor body was shifted
out of place. See page 15 in the Install Guide on how to resolve this.
• If you do see a Green light, the sensor is functioning properly. That
means there is like a wiring problem. Check that the sensor wire har-
ness is properly connected at both ends.
FULL 30s HORN HONK WITH ONLY LIGHT IMPACT TO THE VEHICLE
• You mounted the shock sensor to metal. Remount on a plastic part.
• Turn down the shock sensor sensitivity to 50% or less.
• If you added an optional Ultrasonic sensor, it is very likely that the
controller of the ultrasonic sensor (not the emitters) was placed too
close to the shock sensor. The Ultrasonic sensor’s controller should be
placed more than 30cm (1 foot) away from the shock sensor to avoid
interference.
• Check your Shock Sensor wire harness, end-to-end from the sensor
itself to the 1460 control module, and ensure no other wires are touch-
ing or in close proximity to it (some wiring can cause interference that
can false trigger the shock sensor). Also make sure no RF transmitting
devices are in close proximity to the shock sensor or its wire harness.
CAN’T ARM WITH IGNITION ON
Even if you programmed the Ignition Trigger to RSCM (see page 11),
you cannot Arm using the factory remote Lock button while the Ignition
is ON. However, if you purchase the optional TR537S 2-way paging sys-
tem or the TR365-series 1-way remote, you will then be able to Arm with
the Ignition ON if RSCM is enabled. (Even with the optional remote, you
cannot Arm with IG ON if “IG Protect” mode is enabled.)
TROUBLESHOOTING

© 2020 KIRAMEK, INC., Aichi Japan
Ver.1.4, JUN. 2020
FACTORY KEYLESS UPGRADE SECURITY
series
1460H / H+