Kirby Morgan M-48 MOD-1 User manual

Kirby Morgan Dive Systems, Inc.®
1430 Jason Way Santa Maria, California 93455
Phone: [phone] Fax: [phone]
www.KirbyMorgan.com email: [email protected]
K
I
R
B
Y
M
O
R
G
A
N
D
I
V
E
S
Y
S
T
E
M
S
,
I
n
c
.
© MMXIX Kirby Morgan Dive Systems, Inc. All Rights Reserved Document #181212003 Page 1 of 8
Part #825-070 (S/M) and 825-075 (L/XL)
M-48 MOD-1 Hood Assembly with Bib Kit
Installation Guide
PART NUMBER DESCRIPTION QTY
530-037 Screw 4
530-052 Screw 4
805-070 or 805-075 MOD-1 Hood with Bib S/M or MOD-1 Hood with Bib L/XL 1
840-010 Hood Frame Bracket 4
Tools Required:
• Flathead Screwdriver
• Small Phillips Screwdriver
HOOD
FRAME
PULL TAB
EAR
POCKET
BRACKET
OUTER SEAL

Kirby Morgan Dive Systems, Inc.®
1430 Jason Way Santa Maria, California 93455
Phone: [phone] Fax: [phone]
www.KirbyMorgan.com email: [email protected]
K
I
R
B
Y
M
O
R
G
A
N
D
I
V
E
S
Y
S
T
E
M
S
,
I
n
c
.
© MMXIX Kirby Morgan Dive Systems, Inc. All Rights Reserved Document #181212003 Page 2 of 8
Assembly Procedures
1. Secure all four hood frame brackets with the small
Phillips screws to hood frame.
The hood can be installed with the mask strap on the mask.
2. Bring the hood assembly to the mask, as shown in the
picture.

Kirby Morgan Dive Systems, Inc.®
1430 Jason Way Santa Maria, California 93455
Phone: [phone] Fax: [phone]
www.KirbyMorgan.com email: [email protected]
K
I
R
B
Y
M
O
R
G
A
N
D
I
V
E
S
Y
S
T
E
M
S
,
I
n
c
.
© MMXIX Kirby Morgan Dive Systems, Inc. All Rights Reserved Document #181212003 Page 3 of 8
3. Align tabs to mask and insert screws.
4. Ensure that, on both sides of the mask, the neoprene material tucks inside of the leading edge
where the lens body and jaw frame meet.
This will permit proper removal and replacing of the POD both above and below the water.

Kirby Morgan Dive Systems, Inc.®
1430 Jason Way Santa Maria, California 93455
Phone: [phone] Fax: [phone]
www.KirbyMorgan.com email: [email protected]
K
I
R
B
Y
M
O
R
G
A
N
D
I
V
E
S
Y
S
T
E
M
S
,
I
n
c
.
© MMXIX Kirby Morgan Dive Systems, Inc. All Rights Reserved Document #181212003 Page 4 of 8
5. Stretch the pull tab away from the mask and over the apex of the lower jaw frame. Use the
nylon pocket to capture the apex of the jaw frame.
The comm ports are on the outside of the neoprene – NOT
the INSIDE of the hood.

Kirby Morgan Dive Systems, Inc.®
1430 Jason Way Santa Maria, California 93455
Phone: [phone] Fax: [phone]
www.KirbyMorgan.com email: [email protected]
K
I
R
B
Y
M
O
R
G
A
N
D
I
V
E
S
Y
S
T
E
M
S
,
I
n
c
.
© MMXIX Kirby Morgan Dive Systems, Inc. All Rights Reserved Document #181212003 Page 5 of 8
6. Ensure the leading edge of the outer seal is clear of the mask skirt. The mask skirt should touch
the diver’s face first and the hood outer seal will surround the face where the mask skirt stops.
Repetitive Dives
When doing multiple dives and if the hood is taken on and off, ensure that the hood’s outer seal is
pushed past the mask skirt before donning.
Post Dive
Depending on water conditions, the MOD-1 hood can be left in place when performing post dive
cleaning and inspection. When doing multiple dives for multiple days, it is recommended that the
hood be removed and inspected at least every seven days.

Kirby Morgan Dive Systems, Inc.®
1430 Jason Way Santa Maria, California 93455
Phone: [phone] Fax: [phone]
www.KirbyMorgan.com email: [email protected]
K
I
R
B
Y
M
O
R
G
A
N
D
I
V
E
S
Y
S
T
E
M
S
,
I
n
c
.
© MMXIX Kirby Morgan Dive Systems, Inc. All Rights Reserved Document #181212003 Page 6 of 8

This page intentionally left blank

TM
Kirby Morgan Dive Systems, Inc.
1430 Jason Way
Santa Maria, CA 93455, USA
Telephone [phone], FAX [phone]
E-Mail: [e-mail], Web Site:www.KirbyMorgan.com