KitchenAid KBFN402ESS User manual

BOTTOM-MOUNT
BUILT-IN REFRIGERATOR
Installation Guide
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.
REFRIGERADOR EMPOTRADO CON
CONGELADOR EN LA PARTE INFERIOR
Guía de instalación
IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. LA INSTALACIÓN REQUIERE DE 2 O MÁS PERSONAS.
RÉFRIGÉRATEUR ENCASTRÉ AVEC
CONGÉLATEUR EN DESSOUS
Guide d’installation
IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L’INSTALLATION NÉCESSITE L’INTERVENTION DE 2 PERSONNES OU PLUS.
Table of Contents/Índice/Table des matières ................................................................. 2
W10721177B

2
TABLE OF CONTENTS
REFRIGERATOR SAFETY .............................................................3
MODELS..........................................................................................4
INSTALLATION REQUIREMENTS ................................................5
Tools and Parts ............................................................................5
Location Requirements................................................................6
Electrical Requirements ...............................................................7
Water Supply Requirements........................................................7
Tipping Radius .............................................................................7
Product Dimensions.....................................................................8
Door Swing Dimensions...............................................................9
Overlay Series Custom Panels ..................................................10
Custom Overlay Panel Dimensions ...........................................11
Stainless Steel and Overlay Series Both 36" and
42" models have the same cabinet side trim ............................14
INSTALLATION INSTRUCTIONS ................................................15
Unpack the Refrigerator.............................................................15
Reduce Tipping Radius..............................................................15
Move the Refrigerator into House..............................................15
Install Anti-Tip Boards................................................................16
Connect the Water Supply.........................................................16
Plug in Refrigerator.....................................................................18
Move Refrigerator to Final Location...........................................18
Level and Align Refrigerator.......................................................19
Install Overlay Custom Panels ...................................................19
Adjust Door(s).............................................................................21
Install Side Panel ........................................................................23
Install Base Grille........................................................................23
Complete Installation..................................................................24
ÍNDICE
SEGURIDAD DEL REFRIGERADOR...........................................25
MODELOS.....................................................................................26
REQUISITOS DE INSTALACIÓN.................................................28
Herramientas y piezas................................................................28
Requisitos de ubicación.............................................................28
Requisitos eléctricos..................................................................30
Requisitos del suministro de agua.............................................30
Arco de vuelco ...........................................................................31
Medidas del producto................................................................31
Medidas de oscilación de la puerta...........................................32
Paneles a la medida de la serie de paneles recubiertos...........33
Dimensiones del panel recubierto a la medida .........................34
Paneles y juegos de fábrica para las series Stainless Steel
y de paneles recubiertos (modelos de 36" [91,4 cm]) ..............37
INSTRUCCIONES DE INSTALACIÓN.........................................38
Desempaque el refrigerador ......................................................38
Cómo reducir el arco de vuelco
(si es necesario)..........................................................................38
Cómo hacer entrar el refrigerador en la casa ............................38
Cómo instalar los tableros antivuelco........................................39
Conexión del suministro de agua ..............................................39
Cómo enchufar el refrigerador...................................................42
Cómo mover el refrigerador
a su ubicación final.....................................................................42
Nivelación y alineamiento del refrigerador.................................42
Cómo instalar los paneles a la medida para
la serie de paneles recubiertos ..................................................43
Cómo ajustar la(s) puerta(s) .......................................................44
Cómo instalar el panel lateral.....................................................46
Cómo instalar la rejilla de la base ..............................................46
Cómo terminar la instalación .....................................................47
TABLE DES MATIÈRES
SÉCURITÉ DU RÉFRIGÉRATEUR ..............................................48
MODÈLES .....................................................................................49
EXIGENCES D’INSTALLATION...................................................51
Outillage et pièces......................................................................51
Exigences d’emplacement.........................................................52
Spécifications électriques..........................................................53
Spécifications de l’alimentation en eau .....................................53
Rayon de basculement ..............................................................54
Dimensions du produit...............................................................54
Dimensions pour le pivotement des portes...............................56
Panneaux personnalisés de la série Panneaux décoratifs........57
Panneaux personnalisés décoratifs—Dimensions....................58
Ensembles de panneaux d’origine de la série Stainless
Steelet Panneaux décoratifs (modèles de 36" [91,4 cm]).........61
INSTRUCTIONS D’INSTALLATION.............................................62
Déballage du réfrigérateur..........................................................62
Réduction du rayon de basculement.........................................62
Faire entrer le réfrigérateur dans le domicile .............................62
Installation de planches antibasculement..................................63
Raccordement à l’alimentation en eau ......................................63
Branchement du réfrigérateur....................................................66
Déplacement du réfrigérateur à l'emplacement final.................66
Réglage de l’aplomb et alignement du réfrigérateur .................66
Installation des panneaux personnalisés de la série
Panneaux décoratifs...................................................................67
Ajustement de la (des) porte(s)...................................................68
Installation du panneau latéral ...................................................70
Installation de la grille de la base ...............................................71
Achever l’installation ..................................................................71

3
REFRIGERATOR SAFETY
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.

4
MODELS
Stainless Steel Series (36" [91.4 cm] Models)
Features wraparound styling that complements the contoured
door handles. This series provides a warm commercial-looking
built-in refrigerator.
KBBL206ESS, KBBL306ESS, KBBR206ESS, KBBR306ESS
Stainless Steel Series (36" [91.4 cm] Models)
Features wraparound styling that complements the contoured
door handles. This series provides a warm commercial-looking
built-in refrigerator.
KBFN406ESS, KBFN506ESS
Overlay Series (36" [91.4 cm] Models)
Features factory-installed, overlay style trim, to provide a
“frameless” look. This series requires the installation of custom
panels, handles, and standoffs.
KBBL206EPA, KBBL306EPA, KBBR206EPA, KBBR306EPA
Overlay Series (36" [91.4 cm] Models)
Features factory-installed, overlay style trim, to provide a
“frameless” look. This series requires the installation of custom
panels, handles, and standoffs.
KBFN406EPA, KBFN506EPA

5
INSTALLATION REQUIREMENTS
Tools and Parts
IMPORTANT:
■Installer: Leave Installation Instructions with the homeowner.
■Homeowner: Keep Installation Instructions for future
reference. Save these Installation Instructions for the local
electrical inspector’s use.
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Parts Needed
■#8 x 3" (7.6 cm) wood screws (longer screws may be needed) (6)
■2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s) (1 or 2)
■Make custom panels or consult a qualified cabinetmaker or
carpenter to make the panels.
Overlay Series: Make custom panels, or consult a qualified
cabinetmaker or carpenter to make the panels. See
“Installation Requirements” for more information.
Stainless Series and Black Stainless Series are shipped
complete.
■If you are connecting the water line directly to copper tubing
and not to a shutoff valve, you need a ferrule, a union, and a
¹⁄₄" compression fitting.
Stainless Steel Series (42" [106.7 cm] Models)
Features wraparound styling that complements the contoured
door handles. This series provides a warm commercial-looking
built-in refrigerator.
KBFN402ESS, KBFN502ESS
Black Stainless Steel Series (42" [106.7 cm] Models)
KBFN502EBS
Overlay Series (42" [106.7 cm] Models)
Features factory-installed, overlay style trim, to provide
a “frameless” look. This series requires the installation of
custom panels, handles, and standoffs.
KBFN402EPA, KBFN502EPA
■Cordless drill ■Torx®† T15 and T27 screwdrivers
■Drill bits ■¹¹⁄₃₂" nut driver
■Adjustable
wrenches (2)
■³⁄₈", ¹⁄₄", and ¹⁄₂" open-end
wrenches
■Phillips screwdriver ■⁵⁄₃₂" hex key
■Small level ■¹⁄₄" and ⁵⁄₁₆" socket drivers
■Appliance dolly ■Tape measure
■Utility knife
†®TORX is a registered trademark of Acument Intellectual Properties, LLC.

6
Location Requirements
The refrigerator can be recessed in an opening between cabinets
or installed at the end of a cabinet run using a side panel to
enclose the refrigerator.
IMPORTANT:
■Observe all governing codes and ordinances.
■It is recommended that you do not install the refrigerator near
an oven, radiator, or other heat source.
■Do not install in a location where the temperature will fall
below 55°F (13°C).
■Floor must support the refrigerator weight, more than 600 lbs
(272 kg), door panels and contents of the refrigerator.
■Ceiling height must allow for side tipping radius. See “Tipping
Radius.”
■Location should permit door to open fully. See “Door Swing
Dimensions.”
■Location must permit top grille removal. See “Opening
Dimensions.”
Opening Dimensions
■To avoid tipping during use, the solid soffit must be within
1" (2.5 cm) maximum above the refrigerator. If the solid soffit
is higher than 1" (2.5 cm) or one is not available, then the
refrigerator must be braced.
If anti-tip boards are needed, they must be installed to the
rear wall studs so that the bottom of the anti-tip board is
84" (213.4 cm) from the floor. See “Install Anti-Tip Boards”
for more information.
NOTES:
■A clearance of ¹⁄₂" (1.3 cm) must be maintained above
the top grille in order for the top grille to be removed.
■Do not remove the foam gasket on top of the compressor
cover unless removal is necessary to fit the unit under a
soffit. Removal of the gasket will cause loss in cooling
efficiency.
■If installing under a solid soffit, after, installation raise the
leveling legs so that the gasket is pressed snugly against
the soffit.
■A grounded 3 prong electrical outlet should be placed within
4" (10.2 cm) of the right side cabinets or end panel. See
“Electrical Requirements” for additional information.
■The water shutoff should be located in the base cabinet on
either side of the refrigerator or some other easily accessible
area. If the water shutoff valve is not in the cabinets, the
plumbing for the water line can come through the floor or
the back wall. See “Water Supply Requirements” for more
specific information.
NOTE: Flooring under refrigerator must be at same level as the
room.
A. Gasket
B. Compressor cover
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
¹⁄₂"
(1,3 cm)
B
A
Model Width A (as shown above) Dimension B (as shown above)
36" 35¹⁄₂" to 35³⁄₄"
(90.2cmto90.8cm) 4" (10.2 cm)
42" 41¹⁄₂" to 41³⁄₄"
(105.4 cm to 106 cm) 7¹⁄₂" (19 cm)
6"
(15.2 cm)
24"
(60.96 cm) min.
1"
(2.54 cm)
77"
(196 cm)
6"
(15.2 cm)
6"
(15.2 cm)
A
Width
(see chart following)
B
Dimension
84" (213.4 cm)
to bottom of solid soffit

7
Electrical Requirements
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical
connection.
Recommended Grounding Method
A 115 volt, 60 Hz., AC only, 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord.
IMPORTANT: If this product is connected to a GFCI (Ground
Fault Circuit Interrupter) protected outlet, nuisance tripping of the
power supply may occur, resulting in loss of cooling. Food quality
and flavor may be affected. If nuisance tripping has occurred,
and if the condition of the food appears poor, dispose of it.
NOTE: Before performing any type of installation or cleaning,
remove the top grille and turn the master power switch to OFF
or disconnect power at the circuit breaker box.
When you are finished, turn ON the master power switch or
reconnect power at the circuit breaker box. Then reset the control
to the desired setting.
Water Supply Requirements
■ All installations must meet local plumbing code requirements.
■ The water shutoff should be located in the base cabinet on
either side of the refrigerator or some other easily accessible
area. The right-hand side is recommended. The access hole
through the cabinet must be within
¹⁄₂ " (1.3 cm) of the rear wall.
NOTE: If the water shutoff valve is in the back wall behind the
refrigerator, it must be at an angle so that the tube is not
kinked when the refrigerator is pushed into its final location.
■If the water shutoff valve is not in the cabinets, the plumbing
for the water line can come through the floor. A ¹⁄₂" (12.7 mm)
hole for plumbing should be drilled at least 6" (15.2 cm) from
the right-hand or left-hand side cabinet or panel. On the floor,
the hole should be no more than 1" (2.54 cm) away from the
back wall. See “Connect the Water Supply.”
■If additional tubing is needed, use copper tubing and check
for leaks. Install the copper tubing only in areas where the
household temperatures will remain above freezing.
■Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve
which reduces water flow and clogs more easily.
NOTE: Your refrigerator dealer has a kit available with a
¹⁄₄" (6.35 mm) saddle-type shutoff valve, a union, and copper
tubing. Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes.
Water Pressure
A cold water supply with water pressure between 30 and 120 psi
(207 and 827 kPa) is required to operate the water dispenser and
ice maker. If you have questions about your water pressure, call a
licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and
827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
■Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
■Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
■If your refrigerator has a water filter cartridge, it may further
reduce the water pressure when used in conjunction with a
reverse osmosis system. Remove the water filter cartridge.
If you have questions about your water pressure, call a licensed,
qualified plumber.
Tipping Radius
Be sure there is adequate ceiling height to stand the refrigerator
upright when it is moved into place.
■The dolly wheel height must be added to the tipping radius
when a dolly is used.
■If needed, the tipping radius can be reduced. See “Reduce
Tipping Radius.”
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
24"
(60.96 cm) min.
1"
(2.54 cm) 6"
(15.2 cm)
6"
(15.2 cm)
6"
(15.2 cm)

8
Side Tipping Radius (36" [91.4 cm] Models)
Side Tipping Radius (42" [106.7 cm] Models)
Product Dimensions
Side View
■The depth from the front of the top grille to the back of the
refrigerator cabinet is 25³⁄₈" (64.5 cm).
■The power cord is 84" (213 cm) long.
■Height dimensions are shown with leveling legs extended
¹⁄₈" (3 mm) below the rollers.
*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below
rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.
Top View
36" (91.4 cm) Models
42" (106.7 cm) Models
A. Tip this side only.
A. Tip this side only.
90 ¹⁄₂ "
(229.9 cm)
A
93"
(236.2 cm)
A
A
23¹⁄₂"
(59.7 cm)
84" (213.4 cm)
Power Cord
*83³⁄₈"
(211.8 cm)
*3¹⁄₂" (8.9 cm)
25³⁄₈"
(64.5 cm)
35¹⁄₄"
(89.5 cm)
25³⁄₈"
(64.5 cm)
41¹⁄₄"
(105 cm)

9
Front View
■Width dimensions were measured from trim edge to trim
edge.
■Height dimensions are shown with leveling legs extended
¹⁄₈" (3 mm) below the rollers.
36" (91.4 cm) Models
*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below
rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.
42" (106.7 cm) Models
*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below
rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.
Door Swing Dimensions
The location must permit the door to open to a minimum of 90°.
Allow 5" (12.7 cm) minimum space between the side of the
refrigerator and a corner wall.
NOTE: The required thickness for all panels is ³⁄₄" (1.91 cm). More
clearance may be required if you are using overlay panels or
custom handles.
To adjust the door swing, see “Adjust Door Swing.”
36" (91.4 cm) Single Door Models
36¹¹⁄ " (92.3cm)
*83³⁄₈"
(211.8 cm)
32
42¹¹⁄ " (107.5 cm)
*83³⁄₈"
(211.8 cm)
32
110˚
90˚
23"
(58 cm)
max.
51"
(130 cm)
59"
(150 cm)
130˚

10
36" (91.4 cm) French Door Models 42" (106.7 cm) French Door Models
Overlay Series Custom Panels
Custom overlay panels allow you to blend the exterior of your
refrigerator into the overall kitchen décor and to use custom
handles for additional design flexibility.
The custom panels must have backer panels attached in order
to mount them to the refrigerator. It is most common to work with
three panels, as shown in the following graphic: a decorative
overlay panel, a ¹/₈" (3.18 mm) spacer panel or spacer strips
and a ¹/₄" (6.35 mm) backer panel.
In some cases, your cabinet manufacturer may choose to work
with one panel routed for the different dimensions. Follow these
panel dimension and placement instructions to be sure that the
custom overlay panels will fit properly.
IMPORTANT:
■For 36" (91.4 cm) single-door models, the refrigerator door
overlay panel cannot exceed 50 lbs (23 kg) and the freezer
drawer overlay panel cannot exceed 20 lbs (9.1 kg).
■For 36" (91.4 cm) and 42" (106.7 cm) French-door models,
the refrigerator door overlay panel cannot exceed 30 lbs
(13.5 kg) and the freezer drawer overlay panel cannot exceed
25 lbs (11.4 kg).
■The weight of the top grille overlay panel cannot exceed
10 lbs (4.5 kg) for both models.
To minimize panel weight, you may use 2" (5.08 cm) spacer
strips around the perimeter in place of full-sheet solid spacer
panels. The spacer strips must be set in at least 1" (2.54 cm)
from the top, bottom and side edges of the backer panel. If
you use spacer strips, it is also recommended that you use two
2" (5.08 cm) strips horizontally centered for added support.
110˚
90˚
110˚
90˚
39³⁄₄"
(101 cm)
41"
(104 cm)
110˚
90˚
110˚
90˚
42³⁄₄"
(108.6 cm)
44¹⁄₄"
(112.3 cm)
Overlay Panel Spacer Panel
Backer Panel
⁵⁄₈" to ³⁄₄"
(15.88 to
19.05 mm) ¹⁄₈"
(3.18 mm)
¹⁄₄"
(6.35 mm)
1" minimum
(2.54 cm)
Door/Grille Trim
Spacer Panel
Offset Dimension
¹⁄₈"
(3.18 mm)
Overlay Panel
Backer Panel

11
Custom Overlay Panel Dimensions
Custom Overlay Panels
(36" [91.4 cm] Single Door Models) Custom Backer Panels (36" [91.4 cm] Single Door Models)
34³⁄₄"
(88.27 cm)
7¹⁄₄"
(18.42 cm)
34³⁄₄"
(88.27 cm)
34³⁄₄"
(88.27 cm)
51¹⁄₈"
(129.86 cm)
20³⁄₄"
(52.71 cm)
TOP GRILLE PANEL
Maximum Weight: 10 lbs (4.5 kg)
FREEZER DOOR PANEL
Maximum Weight: 20 lbs (9.1 kg)
REFRIGERATOR DOOR PANEL
Maximum Weight: 50 lbs (23 kg)
33³⁄₄"
(85.73 cm)
6³⁄₁₆"
(15.72 cm)
Bottom Offset
³⁄₈" (9.5 mm)
49¹⁄₈"
(124.78 cm)
20³⁄₁₆"
(51.28 cm)
34¹⁄₄"
(87.00 cm)
34¹⁄₄"
(87.00 cm)
Bottom Offset
⁷⁄₁₆" (11.1 mm)
Bottom Offset
¹⁄₄" (6.35 mm)
Center
Backer
Panel
left to
right
Center
Backer
Panel
left to
right
Center
Backer
Panel
left to
right

12
Custom Overlay Panels
(36" [91.4 cm] French Door Models) Custom Backer Panels (36" [91.4 cm] French Door Models)
3417⁄32"
(87.7 cm)
171/6"
(43.3cm) 171/6" (43.3cm)
3417⁄32"
(87.7 cm)
7¹⁄₄"
(18.4 cm)
513⁄8"
(130.5 cm) 513⁄8" (130.5 cm)
207⁄16"
(51.9 cm)
TOP GRILLE PANEL
Maximum Weight: 10 lbs(4.5 kg)
FREEZER DOOR PANEL
Maximum Weight: 25 lbs(11.4 kg)
REFRIGERATOR
DOOR PANEL
Maximum Weight:
30 lbs(13.5 kg)
REFRIGERATOR
DOOR PANEL
Maximum Weight:
30 lbs(13.5 kg)
33
23
/ 32 "
(85.6 cm)
6
1
/ 4 "
(15.9 cm)
Bottom Offset
1
/ 2 " (1.27 cm)
49
5
/ 16 "
(125.2 cm)
20
3
/ 32 "
(51.0 cm)
16
11
/ 16 "
(42.4 cm)
34
7
/ 32 "
(86.9 cm)
Bottom
Offset
5
/ 8 "
(1.6 cm)
49
5
/ 16 "
(125.2 cm)
Bottom
Offset
5
/ 8 "
(1.6 cm)
Bottom offset
3
/ 16 " (4.7 mm)
Exterior
Panel
extends
above
door.
Side Offset
7
/ 16 " (1.1 cm)
16
11
/ 16 "
(42.4 cm)
Side
Offset
3
/ 16 "
(4.7 mm)
Side
Offset
3
/ 16 "
(4.7 mm)
Side
Offset
5
/ 32 "
(4 mm)

13
3-Piece Grille Overlay Panel Configuration 3-Piece Door Overlay Panel Configuration
1-Piece Overlay Panel Configuration
In some cases, your cabinet manufacturer may choose to work
with one panel routed for the different dimensions. Follow these
panel dimensions and placement instructions to be sure that the
custom overlay panels will fit properly.
Custom Overlay Panels (42" [106.7 cm] French Door Models) Custom Backer Panels (42" [106.7 cm] French Door Models)
Spacer Panels (all models)
NOTE: Spacer panels must be at least 1" (2.54 cm) from the top, bottom, and side edges of the backer panel.
40⁷⁄₁₆"
(102.7 cm)
20"
(50.8 cm) 20" (50.8 cm)
40⁷⁄₁₆"
(102.7 cm)
7¹⁄₄"
(18.4 cm)
51¹⁄₄"
(130.2 cm) 51¹⁄₄" (130.2 cm)
20¹⁄₄"
(51.4 cm)
TOP GRILLE PANEL
Maximum Weight: 10 lbs (4.5 kg)
FREEZER DOOR PANEL
Maximum Weight: 25 lbs (11.4 kg)
REFRIGERATOR
DOOR PANEL
Maximum Weight:
30 lbs (13.5 kg)
REFRIGERATOR
DOOR PANEL
Maximum Weight:
30 lbs (13.5 kg)
395 / 8"
(100.6 cm)
61 / 4"
(15.9 cm)
Bottom Offset
1
/ 2" (1.27 cm)
493 / 16"
(124.93 cm)
197 / 8"
(50.48 cm)
195 / 8"
(49.85 cm)
40"
(101.6 cm)
Bottom
Offset
1
/ 2"
(1.27 cm)
493 / 16"
(124.93 cm)
Bottom
Offset
1
/ 2"
(1.27 cm)
Offset all sides
3
/ 16" (4.7 mm)
Exterior
Panel
extends
above
door.
Side Offset
3
/ 8" (9.5 mm)
195 / 8"
(49.85 cm)
Side
Offset
3
/ 16"
(4.7 mm)
Side
Offset
3
/ 16"
(4.7 mm)
Top View Side View
A. Offset dimension
B.
¹₄ " (6.25 mm) Backer panel
C.
¹₈ " (3.18 mm) Spacer panel
D.
³₄ " (1.92 cm) Decorative overlay
panel
1"
(2.54 cm)
D
C
B
A
A. Offset dimension
B.
¹₄ " (6.25 mm) Backer panel
C.
¹₈ " (3.18 mm) Spacer panel
D.
³₄ " (1.92 cm) Decorative overlay panel
1"
(2.54 cm)
DA C
B

14
Stainless Steel and Overlay Series Both
36" and 42" models have the same
cabinet side trim
All factory parts are available through your KitchenAid dealer or
by calling KitchenAid Parts and Accessories at 1-800-442-9991.
In Canada, call 1-800-807-6777.
Overlay Series Door Handle Kits
The following handle style is available. Contact your KitchenAid
dealer or KitchenAid Parts and Accessories at
1-800-442-9991. In Canada, call 1-800-807-6777.
Refrigerator and Side Trim Dimensions
The width and height of a side panel are determined by the type
of installation you are planning.
NOTES:
■The dimensions shown are actual product dimensions
and may not reflect the needed panel installation
dimensions.
■The side panel should be a minimum of ¹⁄₂" (1.27 cm) thick
to avoid warping.
■If the opening depth is 25" (63.5 cm) or more, you may
want to install a support board on the rear wall.
Refrigerator
Installation Dimensions - Option 1
1. Measure the distance from point A (as shown) to the back
wall. Add 1⁄16" (1.6 mm) to this measurement to allow the side
panel to fit into the trim.
2. If the panel is more than ¹¹⁄₃₂" (8.7 mm) thick, rout the front
edge to allow the side panel to fit into the trim.
Installation Dimensions - Option 2
1. Measure the distance from point A (as shown) to back wall.
2. Rout the front edge of the support board or attach a
¹¹⁄₃₂" (8.7 mm) board to hold the panel in the cabinet side trim.
Knurl grip handle with chrome endcaps
W10782871 - French Door Bottom Mount Handle Kit
W10782874 - Two Door Bottom Mount Handle Kit
11/16"
(18.0 mm)
1/2"
(12.2 mm)
9/16"
(13.9 mm)
5/8"
(15.7 mm)
A
A

15
INSTALLATION
INSTRUCTIONS
Unpack the Refrigerator
IMPORTANT:
■Do not remove the film covering until the refrigerator is in its
operating location.
■All four leveling legs must contact the floor to support and
stabilize the full weight of the refrigerator.
■Keep the cardboard shipping piece or plywood under the
refrigerator until it is installed in the operating location.
1. Remove and save the literature package bag taped to the
side of the refrigerator and the parts bag behind the grille.
Remove the four brackets (two on each side) that attach the
shipping base to the refrigerator bottom.
NOTE: Do not remove tape and door bracing until the
refrigerator is in its final location.
2. If necessary, reduce the tipping radius. See “Tipping Radius”
for ceiling height requirements or “Reduce Tipping Radius”
for step-by-step instructions. If you do not need to reduce the
tipping radius, proceed to “Move the Refrigerator into
House.”
Reduce Tipping Radius
(if required)
Before bringing the refrigerator into the home, be sure there is
adequate ceiling height to stand the refrigerator upright. See
“Tipping Radius” in the “Installation Requirements” section for
more information.
If you do not have adequate ceiling height to stand the
refrigerator upright, the tipping radius can be reduced by
removing the top grille and side trims (see the following chart).
1. Grasp both ends of the top grille.
2. Push the top grille straight up; then pull straight out.
Lay the grille on a soft surface.
3. Remove the 6 screws attaching each cabinet side trim to the
refrigerator and remove the side trims.
Move the Refrigerator into House
1. Place an appliance dolly under the left-hand side of the
refrigerator as shown. Place the corner posts from the
packing materials over the trims and handles as appropriate
to avoid damage. Slowly tighten the strap.
NOTE: Pass the dolly strap under the handles.
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
Model Reduced Tipping Radius
36" 89" (226.1 cm)
42" 90" (228.6 cm)
A. Top grille
B. Cabinet side trim
B BA
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.

16
36" (91.4 cm) Single Door Models
36" (91.4 cm) and 42" (106.7 cm) French Door Models
2. Place pieces of the shipping carton on the floor when rolling
the dolly and refrigerator into the house. Move the refrigerator
close to the built-in opening.
3. Place top of cardboard carton or plywood under refrigerator.
4. Stand the refrigerator up. First, place the left bottom edge of
the refrigerator on the floor, stand the refrigerator upright and
then lower the right-hand side of the refrigerator to the floor.
5. Do not remove film or cover.
6. Reassemble the trim and top grille after the dolly has been
removed from the refrigerator.
Install Anti-Tip Boards
IMPORTANT:
■To avoid tipping during use, the solid soffit must be within
1" (2.5 cm) maximum above the refrigerator. If the solid soffit
is higher than 1" (2.5 cm) or one is not available, then the
refrigerator must be braced.
■It is recommended that board(s) be installed before the
refrigerator is installed.
■Board(s) must be long enough to fully cover the width of the
compressor cover.
■Locate the board(s) so the bottom surface(s) of the board(s) is
(are) 84" (213 cm) from the floor.
■During installation, raise the refrigerator up so there is
¹⁄₄" (6.35 mm) maximum between the top of the refrigerator
and the bottom of the anti-tip board(s). Do not crush the
compressor cover when raising the rear leveling legs.
NOTE: The foam gasket, on top of the compressor cover, will
compress to fit under the anti-tip board(s). There is no need
to trim the gasket.
To Install Anti-tip Boards
1. Mark the stud locations on rear wall.
2. Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x
81 cm) boards to wall studs behind refrigerator. Use six
#8 x 3" (7.6 cm) (or longer) wood screws. The wood screws
must be screwed into the studs at least 1½" (3.8 cm). The
board(s) must overlap the compressor cover.
Connect the Water Supply
Read all directions before you begin.
IMPORTANT: If you turn the refrigerator on before the water line
is connected, turn the ice maker OFF.
Connect to Water Line
Parts Needed
■Minimum 7 ft (2.13 m) flexible, codes-approved water
supply line
Style 1—Shutoff Valve Connection
NOTE: If your water line connection does not look like Style 1,
see “Style 2—Copper Line Connection.”
1. Unplug refrigerator or disconnect power supply.
IMPORTANT:
■There is not enough clearance to achieve a flush installation
if a water shutoff valve is located in the wall behind the
refrigerator. The water shutoff should be located in the base
cabinet on either side of the refrigerator.
■Before attaching the tubing to shutoff valve, flush the main
water supply line to remove particles and air in the water line.
Allow enough flow so that water becomes clear. Flushing the
water line may help avoid filters and/or water valves from
becoming clogged.
A. Center board ¹⁄₄ " (6.35 mm) max. above
refrigerator
B. Two 2" x 4" x 32" (5 cm x 10 cm x
81 cm) boards
C. Attach to studs with six
#8 x 3" (7.6 cm) screws
D. Compressor cover
BA
C
2" (5 cm)
D

17
2. Connect the flexible, codes-approved water supply line to the
water shutoff valve by threading the provided nut onto the
shutoff valve as shown.
3. Place the end of the tubing into a bucket, and turn shutoff
valve ON.
4. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Style 2—Copper Line Connection
NOTE: If there is a water supply line that meets the specifications
in “Water Supply Requirements,” proceed to “Connecting to
Refrigerator.” If not, use the following instructions to connect to
the household cold water supply.
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a ½" to 1¹⁄₄" (1.3 cm to 3.18 cm) vertical cold water
pipe near the refrigerator.
IMPORTANT:
■Make sure it is a cold water pipe.
■Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and keep normal sediment from collecting in the
valve.
4. Determine the length of copper tubing you need. Measure
from the connection on the refrigerator to the water pipe.
Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D.
(outside diameter) copper tubing. Be sure both ends of
copper tubing are cut square.
5. Using a cordless drill, drill a ¹⁄₄" (6.35 mm) hole in the cold
water pipe you have selected.
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so washer makes a watertight seal.
Do not overtighten.
IMPORTANT: Before attaching the tubing to shutoff valve, flush
the main water supply line to remove particles and air in the water
line. Allow enough flow so that water becomes clear. Flushing the
water line may help avoid filters and/or water valves from
becoming clogged.
7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten
the clamp or the sleeve. This will crush the copper tubing.
8. Turn off the shutoff valve on the water pipe. Coil the copper
tubing.
9. Connect the flexible, codes-approved water supply line to the
water shutoff valve by threading the provided nut onto the
shutoff valve.
10. Place the end of the tubing into a bucket, and turn shutoff
valve ON.
11. Check for leaks around the saddle valve. Tighten any nuts or
connections (including connections at the valve) that leak.
Connect to Refrigerator
Parts Supplied
■¹⁄₄" to ¹⁄₄" (6.35 mm to 6.35 mm) male-to-male coupling
NOTE: The flexible, codes-approved water supply line should
connect to the supply valve through the floor.
1. Unplug the refrigerator or disconnect power.
2. Connect the 7 ft (2.13 m) flexible codes-approved water tube
to the water supply valve.
3. Flush the main water supply line to remove particles and air
in the water line. Allow enough flow so that water becomes
clear.
A. Bulb
B. Nut
C. Water tubing
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
E. Compression sleeve
F. Shutoff valve
G. Packing nut
A
B
C
A
B
C
DEF
G
1"
(2.54 cm)
7"
(17.78 cm)
6"
(15.2 cm)
6"
(15.2 cm)

18
4. Tape the 7 ft (2.13 m) flexible codes-approved water supply
line to the floor, 7" (17.78 cm) from the left side of the
refrigerator. Tape along the length of the tubing, which will
allow it to pass beneath the refrigerator without interference.
NOTE: Allow a minimum of 26" (66.04 cm) of flexible codes -
approved water supply line to be loose at the front of the
refrigerator for connecting to the refrigerator.
5. Connect the 7 ft (2.13 m) flexible codes-approved water
supply line to the refrigerator.
NOTE: If the main water shutoff valve is behind the
refrigerator, a secondary water shutoff valve may be installed
in line with the water supply line at the front of the product.
Overmold Coupling (on some models)
Discrete Coupling (on some models)
6. Turn on the water supply valve and check all connections
for leaks.
Plug in Refrigerator
1. Set control switch at top of cabinet to the OFF position.
2. Plug into a grounded 3 prong outlet.
Move Refrigerator to Final Location
IMPORTANT: To avoid floor damage, make sure levelers are
raised (not touching floor) and refrigerator is on rollers before
moving.
1. Place top of cardboard carton or plywood under refrigerator.
Remove dolly.
2. Do not remove film or cover.
3. Move the refrigerator straight back and evenly into the
opening. Be sure that the refrigerator side trims are not
interfering with the door opening. Also, be sure that the
water tubing is not kinked and the power supply cord is
on top of the refrigerator.
A. Household water line
B. Nut (purchased)
C. Ferrule (purchased)
A. Household water line
B. Nut (purchased)
C. Ferrule (purchased)
D. Coupling
E. Bulb
F. Nu t
G. Refrigerator water tubing
AB C
ABCD
EFG
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.

19
Level and Align Refrigerator
IMPORTANT: All four leveling legs must contact the floor to
support and stabilize the full weight of refrigerator. Rollers are for
moving refrigerator and not for permanent support.
After moving the refrigerator to its final location:
1. Use a ⁵⁄₁₆" socket driver to turn the leveling bolts clockwise to
extend the legs to the floor as shown. The rollers should be
off the floor.
2. Adjust the leveling legs to level and align the refrigerator from
left to right and front to back so that the refrigerator is level
and aligned with the cabinetry. The cabinetry surface must be
plumb for the ideal fit of the refrigerator side trim.
3. Continue adjusting all of the leveling legs to raise the
refrigerator until the top is within at least 1" (2.54 cm) of
the top soffit.
NOTE: If an anti-tip board has been used, adjust the leveling
legs until the top of the refrigerator is within ¹⁄₄" (6.35 mm) of
the bottom of the anti-tip board as shown. Do not crush the
compressor cover.
IMPORTANT: Adjust in small increments to keep from
damaging the cabinet trim and causing problems with
the door alignment or top grille fit. To avoid damage to
the cabinet or leveling legs, do not apply more than
50 inch-pounds (5.65 Nm) of torque to the leveling
bolts. The leveling legs can be extended to a maximum
of 1¹⁄₄" (3.18 cm) below the rollers.
4. For Overlay models, additional adjustments may be needed
after the custom panels are installed.
Install Overlay Custom Panels
IMPORTANT:
■Install the custom handles prior to installing the panels on
the refrigerator. For more information on KitchenAid
custom handle selection, refer to the KitchenAid Catalog,
visit www.kitchenaid.com, or call 1-800-422-1230.
In Canada, visit www.kitchenaid.ca, or call
1-800-807-6777.
■Create custom door overlay panels according to the
specifications in the “Overlay Series Custom Panels”
section.
■KitchenAid is not responsible for the removal or addition
of molding or decorative panels that would not allow
access to the refrigerator for service.
A. Rear leveling bolt
B. Front leveling bolt
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
A B A
B
A. Center board ¹⁄₄ " (6 mm) max. above refrigerator
B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards
C. Attach to studs with six #8 x 3" (7.6 cm) screws
D. Compressor cover
BA
C
2" (5 cm)
D
¹⁄₄" (6 mm)
max.

20
Door Panel Installation
1. Remove all tape and door bracing from the refrigerator
door(s) and freezer drawer.
2. Open the refrigerator door(s) and freezer drawer and remove
the trims and corner caps on each door as shown.
3. Slide the custom panels into the trims on the refrigerator
door(s) and freezer drawer, making sure that the backer panel
fits into the hinge side trims.
4. Reinstall the trims and corner caps.
5. Remove the film from the screw covers. Snap the screw
covers into the handle trim section.
Top Grille Panel
1. Grasp both ends of the top grille.
2. Push straight up; then pull straight out. Place the top grille
panel-side down on a soft working surface.
3. Remove one end cap by loosening the nuts and sliding the
end cap off.
4. Slide the custom panel into the top grille channel and
reattach the end cap.
A. Corner caps
B. Refrigerator door trims
C. Freezer drawer trim
A. Panels
B
A
B
A
C
AA
AA
A. Top grille
B. Cabinet side trims
A. Bottom rail
B. Nuts
C. End cap
D. Top rail
A. Custom panel
B BA
C
B
A
D
A