KitchenAid KXI9736YSS0 Product information sheet

I_Jtc enAid _
36" (91.4 CM) AND 48" (121.9 CM)
DESIGNER COMMERCIAL-STYLE ISLAND-
MOUNT CANOPY HOOD
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230
or visit our website at www,kitchenaid,com
In Canada, for assistance, installation and service, call: 1-800-807-6777
or visit our website at www, KitchenAid,ca
P
HO I'I'E D'EXTRACTION STYLISEE POUR
APPLICATIONS COMMERCIALES DE
36" (91,4 CM) ET 48" (121,9 CM)POUR CUISINE
CONFIGUREE EN ILOT
Au Canada, pour assistance, installation ou service composez le 1-800-807-6777
ou visitez notre site web &www, KitchenAid,ca
Table of Contents/Table des matieres ............................................................................. 2
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.
FOR RESIDENTIAL USE ONLY.
IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.
POUR UTILISATION RI'--SIDENTIELLE UNIQUEMENT.
LI3ZH B/W10331010C

TABLEOF CONTENTS
RANGE HOOD SAFETY ................................................................. 2
INSTALLATION REQUIREMENTS ................................................ 4
Tools and Parts ............................................................................ 4
Location Requirements ................................................................ 4
Venting Requirements .................................................................. 5
Electrical Requirements ............................................................... 6
INSTALLATION INSTRUCTIONS .................................................. 7
Prepare Location .......................................................................... 7
Install Range Hood ....................................................................... 7
Install Range Hood Internal Blower Motor ................................... 9
Install Range Hood In-Line (External Type)
Blower Motor .............................................................................. 11
Make Electrical Connections for In-Line Blower
Motor System ............................................................................. 12
Make Electrical Power Supply Connection to Range Hood ..... 14
Install Chimney Covers .............................................................. 14
Complete Installation and Check Operation .............................. 15
RANGE HOOD USE ...................................................................... 15
Range Hood Controls ................................................................ 16
RANGE HOOD CARE ................................................................... 16
Cleaning ...................................................................................... 16
WIRING DIAGRAM ....................................................................... 17
ASSISTANCE OR SERVICE ......................................................... 18
In the U.S.A................................................................................ 18
In Canada ................................................................................... 18
Accessories ................................................................................ 18
WAR RANTY .................................................................................. 19
TABLEDES MATIERES
SECURITE DE LA HOTTE DE CUISINIERE ............................... 20
EXIGENCES D'INSTALLATION ................................................... 22
Outils et pieces ........................................................................... 22
Exigences d'emplacement ......................................................... 22
Exigences concernant I'evacuation ........................................... 23
Specifications electriques .......................................................... 25
INSTRUCTIONS D'INSTALLATION ............................................. 26
Preparation de I'emplacement ................................................... 26
Installation de la hotte ................................................................ 27
Installation du moteur du ventilateur interne de la hotte ...........28
Installation du moteur du ventilateur en ligne (externe)
de la hotte ................................................................................... 30
Realisation des connexions electriques du systeme
du moteur du ventilateur en ligne .............................................. 31
Connexion de I'alimentation electrique & la hotte ..................... 32
Installer les cache-cheminee ...................................................... 33
Achever I'installation et verifier le fonctionnement .................... 34
UTILISATION DE LA HOTTE ....................................................... 35
Commandes de la hotte de cuisiniere ....................................... 35
ENTRETIEN DE LA HO'R'E .......................................................... 36
Nettoyage ................................................................................... 36
SCHI_MA DE CABLAGE ............................................................... 37
ASSISTANCE OU SERVICE ......................................................... 38
Au Canada .................................................................................. 38
Accessoires ................................................................................ 38
GARANTIE ..................................................................................... 39
RANGE HOOD SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
2

iMPORTANT SAFETY iNSTRUCTiONS
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
[] Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
[] Before servicing or cleaning the unit, switch power off at
service panel and lock the service disconnecting means to
prevent power from being switched on accidentally. When
the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such as a tag,
to the service panel.
[] Installation work and electrical wiring must be done by
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction.
[] Do not operate any fan with a damaged cord or plug.
Discard fan or return to an authorized service facility for
examination and/or repair.
[] Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent backdrafting. Follow the
heating equipment manufacturer's guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
[] When cutting or drilling into wall or ceiling; do not damage
electrical wiring and other utilities.
[] Ducted fans must always be vented outdoors.
CAUTION: For general ventilating use only. Do not use
to exhaust hazardous or explosive materials and vapors.
CAUTION: To reduce risk of fire and to properly exhaust
air, be sure to duct air outside - do not vent exhaust air into
spaces within walls or ceilings, attics or into crawl spaces,
or garages.
WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
WARNING: TO REDUCE THE RISK OF A RANGE TOP
GREASE FIRE:
[] Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
[] Always turn hood ON when cooking at high heat or when
flambeing food (i.e. Crepes Suzette, Cherries Jubilee,
Peppercorn Beef Flamb6).
[] Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.
[] Use proper pan size. Always use cookware appropriate for
the size of the surface element.
WARNING: TO REDUCE THE RISK OF INJURY TO
PERSONS IN THE EVENT OF A RANGE TOP GREASE
FIRE, OBSERVE THE FOLLOWING: a
[] SMOTHER FLAMES with a close fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO
PREVENT BURNS. If the flames do not go out
immediately, EVACUATE AND CALL THE FIRE
DEPARTMENT.
[] NEVER PICK UP A FLAMING PAN - you may be burned.
[] DO NOT USE WATER, including wet dishcloths or towels -
a violent steam explosion will result.
[] Use an extinguisher ONLY if:
- You know you have a class ABC extinguisher, and you
already know how to operate it.
- The fire is small and contained in the area where it
started.
- The fire department is being called.
- You can fight the fire with your back to an exit.
aBased on "Kitchen Fire Safety Tips" published by NFPA.
[] WARNING: To reduce the risk of fire or electrical shock,
do not use this fan with any solid-state speed control
device.
READ AND SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS
__ _ _ .,S_ x'_@_
a 0 _: t>
Gather the required tools and parts before starting installation.
Read and follow the safety instructions provided with any tools
listed here.
•Horizontal support
• 4- 5 x 45 mm mounting screws
• 72 - 4.2 x 8 mm mounting screws
• T-20 TORX®tadapter
Tools needed
• Level
• Drill
• 1V4" (3.0 cm) drill bit
• Pilot hole drill bits (determined by chimney support
attachment method)
• 3/16"(5 ram) drill bit if installing in-line blower motor system
• Pencil
• Wire stripper or utility knife
• Tape measure or ruler
• Pliers
• Caulking gun and weatherproof caulking compound
• Jigsaw or keyhole saw
• Flat-blade screwdriver
• Phillips screwdriver
• Vent clamps
• Metal snips
Parts needed
• 1 UL listed or CSA approved, 1/2"(12.5 ram) strain relief
• 3 UL listed wire connectors
• Home power supply cable
• 4 Concrete anchors for 1/4"x 4" hex head lag bolts
(for concrete installation)
• 1 Wall or roof cap
• Metal vent system
• Blower motor system - internal or external (See "Blower
Motor System" in the "Accessories" section.)
Parts supplied
Remove parts from packages. Check that all parts were included.
• Hood canopy assembly with ventilator and light bulbs
installed
• 2 Grease Filters for 36" (91.4 cm) models
3 Grease Filters for 48" (121.9 cm) models
• Mounting template
• 2 Support brackets
• 8 Vertical supports
• 2 Vent cover supports
• 2 Upper chimney covers
• 2 Lower chimney covers (front and rear)
• Upper horizontal support bracket
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility to comply with installation clearances
specified on the model/serial rating plate. The model/serial rating
plate is located inside the range hood on the rear wall of the
range hood.
Island hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions provide minimum clearance.
It is recommended that the hood be fastened into solid wood.
The island hood is factory set for venting through the roof or
through the wall.
All openings in ceiling and where island hood will be installed
must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.
Product Dimensions
Vented Installations
19" (48.2
f
441%e'' (114.1 crn) max.
31W' (80 crn) min.
36" (91.4
48" (121.9 cm) !7%6"(70.0 crn)
1-®TORX is a registered trademark of Saturn Fasteners, Inc.

Installation Clearances
T
x
l
T
See NOTE*
36" (91.4 cm)
Countertop
height
IMPORTANT:
Minimum distance "X": 24" (61.0 cm) to electric cooking
surface
Minimum distance "X": 30" (76.2 cm) to gas cooking surface
Suggested maximum distance "X": 36" (91.4 cm)
The chimneys can be adjusted for different ceiling heights. See
the following chart.
Vented Installations
Min. ceiling height Max. ceiling height
Electric cooking 7' 8" (2.34 m) 9' 8" (2.95 m)
surface
Gas cooking 8' 2" (2.49 m) 9' 8" (2.95 m)
surface
*NOTE: The hood chimneys are adjustable and designed to meet
varying ceiling or soffit heights depending on the distance "X"
between the bottom of the hood and the cooking surface. For
higher ceilings an extension kit (Part Number W10352732) is
available, see your dealer. The chimney extension replaces the
upper chimney shipped with the hood.
Vent system must terminate to the outside.
Do not terminate the vent system in an attic or other enclosed
area.
• Do not use 4" (10.2 cm) laundry-type wall caps.
• Use metal vent only. Rigid metal vent is recommended. Do
not use plastic or metal foil vent.
• The vent system must have a damper. If the roof or wall cap
has a damper, do not use the damper supplied with the range
hood.
For the most efficient and quiet operation:
• Use no more than three 90° elbows.
• Make sure there is a minimum of 24" (61 cm) of straight vent
between the elbows if more than 1 elbow is used.
• Do not install 2 elbows together.
• Use clamps to seal all joints in the vent system.
• Use caulking to seal exterior wall or roof opening around the
cap.
• The size of the vent should be uniform.
Cold Weather Installations
An additional back draft damper should be installed to minimize
backward cold air flow and athermal break should be installed to
minimize conduction of outside temperatures as part of the vent
system. The damper should be on the cold air side of the thermal
break.
The break should be as close as possible to where the vent
system enters the heated portion of the house.
Makeup Air
Local building codes may require the use of makeup air systems
when using ventilation systems greater than specified CFM of air
movement. The specified CFM varies from locale to locale.
Consult your HVAC professional for specific requirements in your
area.
Venting Methods
Typical Internal Blower Motor System Venting Installations
A 10" (25.4 cm) round vent system is needed for installation (not
included). The hood exhaust opening is 10" (25.4 cm) round.
NOTE: Flexible vent is not recommended. Flexible vent creates
back pressure and air turbulence that greatly reduce
performance.
Vent system can terminate either through the roof or wall. Tovent
through a wall, a 90° elbow is needed.
Roof Venting Wall Venting
AI
B1
( ; 1
1
A. Roof cap
B. 10" (25.4 cm) round vent A. Wall cap B. 10" (25.4 cm) round vent

Typical In-line Blower Motor System Venting Installations
G
H
A
A. 10" (25.4 cm) round vent
B. Mount on top of ceiling joists.
C. Roof caps
D. Plywood (optional for some installations)
E. Mount on underside of roof rafters.
F. Mount from cross-members tied to trusses.
G. Duct horizontal; mount to cross-members
tied to trusses.
H. Waft cap
Calculating Vent System Length
To calculate the length of the system you need, add the
equivalent feet (meters) for each vent piece used in the system.
Vent piece
45° elbow 2.5 ft
(0.8 m)
90° elbow 5.0 ft
(1.5 m)
Observe all governing codes and ordinances.
Ensure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA 70 (latest
edition), or CSA Standards C22.1-94, Canadian Electrical Code,
Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes
and ordinances.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
• A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is
required.
• If the house has aluminum wiring, follow the procedure
below:
1. Connect a section of solid copper wire to the pigtail
leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors and/or tools
designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer's recommended
procedure. Aluminum/copper connection must conform with
local codes and industry accepted wiring practices.
Wire sizes and connections must conform with the rating of
the appliance as specified on the model/serial rating plate.
The model/serial plate is located behind the filter on the rear
wall of the range hood.
Wire sizes must conform to the requirements of the National
Electrical Code, ANSI/NFPA 70 (latest edition), or CSA
Standards C22.1-94, Canadian Electrical Code, Part 1 and
C22.2 No. 0-M91 (latest edition) and all local codes and
ordinances.
The maximum equivalent vent lengths are:
10" (25.4 cm) round vents - 60 ft (18.3 m)
Example Vent System
90oe,bow _ 6ft(1.8m)__ I .........Wal, cap
The following example falls within the maximum vent length of
60 ft (18.3 m).
1 - 90° elbow
1 - wall cap = 0.0 ft (0.0 m)
8 ft (2.4 m) straight = 8.0 ft (2.4 m)
System length = 13 ft (3.9 m)
6

INSTALLATION INSTRUCTIONS
• It is recommended that the vent system be installed before 1.
the range hood is installed.
• Before making cutouts, make sure there is proper clearance 2.
within the ceiling for exhaust vent.
• Range hood is to be installed 24" (61.0 cm) min. for electric
cooking surfaces, 30" (76.2 cm) min. for gas cooking
surfaces, to a suggested maximum of 36" (91.4 cm) above
the cooking surface. 3.
• Check your ceiling height and the range hood height
maximum before you select your hood. 4.
1. Disconnect power. 5.
2. Determine which venting method to use: roof or wall.
3. Select a flat surface for assembling the range hood. Place
covering over that surface.
Excessive Weight Hazard
Use two or more people to move and install
range hood.
Failure to do so can result in back or other injury.
4. Using 2 or more people, lift range hood onto covered surface.
5. Remove knockout in the back of the terminal box and install a
UL listed or CSA approved 1/2"strain relief.
Range Hood Mounting Screws Installation
1. Determine and mark the centerline on the ceiling where the
range hood will be installed, considering the requirements for
ceiling support structures. See the "Location Requirements"
section. Make sure the range hood is centered over the
cooking surface.
2. Tape template in place on the ceiling at the marked
centerline.
3. Use a pencil to mark the mounting screws, wire access and
duct hole locations on the ceiling.
NOTE: Mounting hole locations should be into the ceiling
support structure.
Remove the template.
4. Drill 4 - ¾e" (4.8 mm) pilot holes for mounting the upper
horizontal support.
Complete Preparation
Determine the required location for the home power supply
cable and drill a 1/2"(1.3 cm) diameter hole for wire access.
Run wire through the home power supply cable according to
the National Electrical Code or CSA Standards and local
codes and ordinances. There must be enough 1/2"conduit
and wires from the fused disconnect (or circuit breaker) box
to make the connection in the hood's electrical terminal box.
NOTE: Do not reconnect power until installation is complete.
Use caulk to seal all openings.
Using a jigsaw or keyhole saw, cut a 10W' (26.0 cm) diameter
hole for the vent duct.
Attach the upper horizontal support bracket with 4 - 5 x
45 mm wood screws.
A. Upper horizontalsupport
IMPORTANT: All screws must be installed into wood. If there
is no wood to screw into, additional wall framing supports
may be required.
.......... iiIoo+1
NOTE: Your range hood requires you to purchase either an
internal type or an in-line (external type) blower motor system.
For internal blower systems, there are blower motor mounting
parts in the blower motor installation packet that must be added
to the range hood prior to mounting the range hood to the ceiling.
See the "Install Range Hood Internal Blower Motor" section and
the instructions supplied with the blower motor.
1. Before installing the range hood, remove the lower support
bracket that is secured with 4 screws on the inside of the
range hood.

2. Installthetransitionpieceusing3-4.2x8mmmounting
screwstotherangehoodcanopy.
3. InstallthelowersupportbracketremovedinStep1usingthe
10-4.2x8mmmountingscrewstotherangehoodcanopy.
i __ _ _ _
g..................... _ i
A
i
i
i
i
A. Lower support bracket
B. 4.2 x 8 mm mounting screws
C. Transition piece
4. Position the 4 vertical supports (A) with the notches at the
bottom and attach to the range hood using 16 - 4.2 x 8 mm
screws.
5. Attach the horizontal support (B)to the vertical supports (A) in
either the first or third set of holes from the top of the vertical
supports.
A. Vertical supports
B. Horizontal support
C. Notched end
6=
7=
Attach a second set of vertical supports (A) and set the
vertical height (B). See "Installation Clearances" in the
"Location Requirements" section to help determine the
desired dimension for vertical height "B."
AIA : B
A. Vertical supports
B. Vertical height
Attach the range hood assembly to the upper horizontal
support attached to the ceiling using 16 - 4.2 x 8 mm screws
and tighten.
! I
A. Mounting screws
8. Install the 4 supports using 8 - 4.2 x 8 mm screws.
NOTE: The notch in the supports (B) must be to the external
side when mounted.
9. Attach the vertical duct cover supports using 4 - 4.2 x 8 mm
screws.
A. Notch in support
B. Support
C. 4.2 x 8 mm screws
D. Vertical duct cover support
8
Connect Vent System
1. Install vent system.
2. Push duct over the exhaust outlet. Seal all connections with
vent clamps.

NOTE:Yourrangehoodrequiresyoutopurchaseeitheran
internaltypeoranin-line(externaltype)blowermotorsystem.
See"BlowerMotorSystem"inthe"Accessories"section.
PreparetheInternalBlowerSystem
• Five6mmnutsarerequiredforthedualmotorsystem.
Clipnutsintothesmallsquarenotches,onelocatedinthe
frontofthesquareventopeningandtheotherfour
locatedattheleftandrightendsofthesquarevent
opening.
IMPORTANT:Performsteps1-4beforemountingtherange
hood.
1. Removegreasefiltersfromrangehood.Seethe"Range
HoodCare"sectionintheUseandCareGuide.
2. Installthemotorsupportbracketusingthree4.2x8mm
screws.Screwbrackettotheinsidetoporback(alternate
locationonsomemodels),towardtheleftsideoftherange
hood.
3. Installmotorspringclipusingtwo4.2x8mmscrews.Screw
springcliptotheinsidetoporback(alternatelocationon
somemodels)oftherangehoodattheproperlocationforthe
selectedmotorsystem.Slidethemountingtabofthespring
clipthroughtheslotinthepanelandsecurewiththescrews.
Usetheinsidesetofmountingholesforthesinglemotor
system.Usetheoutsidesetofmountingholesforthedual
motorsystem.
\
B
A. Clip nut (6 mm) locations for dual motor assembly (quantity 5)
B. Clip nut (6 mm) locations for single motor assembly (quantity 2)
5. Mount range hood. See the "Install Range Hood" section.
Install Range Hood Internal Blower Motor
1= Install the range hood blower motor assembly inside the
range hood canopy with the wiring connection to the left for
the single motor system and to the front or top for the dual
motor system.
4=
D E
A. 4.2 x 8 mm screws (3) for motor support bracket
B. 4.2 x 8 mm screws (2) for motor spring clip
C. Motor support bracket
D. Motor spring clip (single motor assembly location)
E. Motor spring clip (dual motor assembly location)
Install the 6 mm nuts to the outside top or outside back
(alternate location on some models) of the range hood at the
proper location for the selected motor system.
• Two 6 mm nuts are required for the single motor system.
Clip nuts into the small square notches located at the left
and right end of the square vent opening.
Single Blower Motor Assembly
A
A. Wiring connec#on

Dual Blower Motor Assembly
A
A. Wiringconnection
2. Slide the left mounting plate flange under the motor mounting
bracket.
4.
5.
Push the right end of the motor mounting plate up and snap it
into the spring tab.
NOTE: The spring tab should be outside the slot in the
mounting plate.
J
A. Motor mounting plate
B. Spring clip
Align mounting holes in motor mounting plate with motor
mounting clip nuts and install 6 x 16 mm screws and 6.4 mm
lock washers (quantity 2 for single motor; quantity 5 for dual
motor).
3=
s
A B
A. Motor mounting bracket
B. Mounting plate left flange
Run the power supply wires and connector from the range
hood through the hole in the right end of the motor mounting
plate.
A
AB..............i Y
6=
A. Screw with lock washer
B. Mounting hole in motor mounting plate
C. Clip nut (6 mm)
Attach power supply connector from the range hood to the
connector on the blower motor assembly wiring box.
A. Motor mounting plate hole
B. Power supply wires and connector A
7.
A. Wiring box connector
B.Power supply connector from range hood
Go to the "Make Electric Power Supply Connection to Range
Hood" section.
10