Whirlpool RH2600XL-1 SERIES User manual

VENTLESS KITCHEN RANGE HOOD
FOR 120 V. OPERATION
VENTLESS
INSTALLATION
KITCHEN
RANGE HOOD
MODEL
RH2600XL-1
SERIES
READ AND SAVE THESE INSTRUCTIONS
Before you begin, read the following instructions completely
and carefully. If followed, they will simplify the installation
job.
IMPORTANT: OBSERVE ALL GOVERNING CODES
AND ORDINANCES
I I
SAVE THESE INSTRUCTIONS FOR THE LOCAL
ELECTRICAL INSPECTOR’S USE
Your range hood has been designed to filter out smoke,
odors and grease which rise from the cooking surface.
Before you begin the installation be sure that all parts and
accessories are removed from carton. For best results and
ease in the rnstallation of this range hood, read the
instructions sheet to become familiar with the step by step
installation. Figure 1
TOOLS AND MATERIALS REQUIRED
Drill, electric or ratchet drive, with 1’55” wood bit (to drill an
access hole in the cabinet or kitchen wall for the electric
power line.)
One common head screwdriver (to secure hood mounting
screws to the cabinet and hood sheet metal parts).
Plrers (for opening knockouts)
Pencil, ruler and level for marking cabinet locations
Saber saw or keyhole saw for cutting the wall or cabinet
openings.
A626-66EW330871 A
Page 1

TO INSTALL RANGE HOOD
For most efficient operation, top of hood should be
approximately 66 (167.6 CM) inches from floor.
1. Mark locations for electrical wiring from dimensions
grven in Figure 1.
2 Cut hole to accomodate electrical wiring. Be sure to
minimize openings through outside walls or the ceiling.
These will have to be sealed later.
3. Run wire through wall or cabinets according to
National Electrical Code and applrcable local codes. DO
NOT turn power on until installation is complete.
4. Remove screws holding junction box cover. See
Frgure 2.
5. Lrft the hood into position and mark the location of
each of the four keyhole mounting slots.
6 Remove the hood and start all four screws in the
center of the narrow neck of the keyhole slot marked on the
cabinet bottom.
7. Lift the hood into position srmultaneously feeding
the electrical wire through the knockout.
8. Tighten four mounting screws to secure hood to
cabrnet Be sure the screw heads are in the narrow neck of
the keyhole slot. See Figure 3.
9 Complete electrrcal wiring In the junction box
according to the National Electrical Code and applicable
local codes.
NOTE, Thus unit must be permanently grounded
10 Replace junction box cover. See Figure 2.
11 Seal holes around wiring passing through ceiling or
outside wall with caulking or lnsulatron to prevent energy
loss.
KEYHOLE SLOT
IN CANOPY
Figure 2
Figure 4
SCREW --
(IN INSTALLATION
PARTS BAG)
Figure 3
Page 2

OPERATION AND CARE OF UNIT
COMBINATION FILTER:
This filter should be inspected periodically and when it
becomes saturated should be replaced. There are no effec-
tive means of reactivating this filter.
LIGHTS:
Do not use bulb larger than 60 watts in light socket.
CARE OF EXTERIOR SURFACES:
Your range hood is a beautifully finished addition to your
kitchen and requires only the care you give your range to
preserve its lasting beauty. Clean with a mild detergent to
preserve finish DO NOT use abrasive cleaners.
CARE OF FAN MOTOR:
Fan motor has life time sealed bearings that never need
oiling under normal usage. A few drops on each bearing after
three years of heavy usage will prolong the motor life. Clean
motor with a damp cloth and grease cutting detergent when
a heavy coating of grease has accumulated.
For most effectrve removal of smoke and odors; turn on fan at
beginning of cookrng operation and allow to run until smoke
and odors are removed from room.
IMPORTANT SAFEGUARDS FOR
ELECTRICAL APPLIANCES
When using electrical appliances, basic safety precautions
should always be followed including the following:
1. Read and follow all instructions
2. Close supervrsron is necessary when any appliance is
used by or near children.
3. To avoid providing fuel for a grease pan fire, clean lint
and grease from all hood surfaces-interior and exterior, Be
sure to replace air filter every three months.
4. Do not saturate electrical connections, switches, and
motor in water during cleaning. Remember, WATER AND
ELECTRICITY DO NOT MIX!
5. If any electrical malfunction becomes evident during
use, disconnect power to hood at your home fuse or breaker
box.
6. To prevent the risk of fire, electric shock, or injury, be
sure to disconnect power before cleaning or servicing.
WARNING: To reduce the risk of fire or electric shock. do
not use this fan with any solid-state speed control device.
If you need service or assistance, we suggest you follow these four steps:
1. Before calling for assistance... l If you need service...
Performance problems often result from Itttle lhings you can find
and fix yourself wrthout tools of any krnd.
If nothing operates:
l Have you checked the marn fuse or circuit breaker box?
Whrrlpool has a natron-
wade network of franchised
TECH-CARE” Service
Companies. TECH-CARE
service technlclans are
to fulfill the product warranty
and orovlde after-warranty
2
0
If you need assistance...
service anywhere in the United States. To locate TECH-CARE
service in your area, call our COOL-LINE servrce assistance
telephone number (see Step 2) or look in your telephone drrectory
Yellow Pages under,
Call the Whirlpool COOL -LINE@ service assistance telephone
number. Dial free from:
Continental U.S. [phone]
Michigan. [phone]
Alaska& Hawaii.. [phone]
and talk with one of our trained Consultants. The Consultant can
Instruct you In how to obtain satisfactory operation from your
appliance or, If service IS necessary recommend a qualified service
company In your area.
APPLIANCES-HOSEHOLD ELECTRICALAPPLIANCES-
MAJOR-SERVICE h REPAIR MAJOR--REPAIRING 6 PARTS
WHIRLPOOL APPLIANCES
OR
WHIRLPOOL APPLIANCES
FRANCHISED TECH-CARE SERVICE FRANCHISED TECH-CARE SERVICE
SERVICE COMPANIES SERVICE COMPANIES
XYZ SERVICE CO XYZ SERVICE CO
123Maple 999-9999 OR 123MapIe 999-9999
WASHING MACHINES, DRYERS
A IRONERS-SERVICING
WHIRLPOOL APPLIANCES
FRANCHISED TECH-CARE SERVICE
SERVICE COMPANIES
XYZ SERVICE CO
123 Maple 999-9999
4
l If you have a problem...
Call our COOL-LINE service assrstance telepone number (see
Step 2) and talk with one of our Consultants, or If you prefer, write to
Mr. Robert Stanley, Dlvrsion Vice President
WhIrlpool Corporation
AdministratIve Center
2000 US-33 North
Benton Harbor, Ml 49022
If you must call or write, please provide model number, senal
number, date of purchase, and a complete description of the
problem. Thus information IS needed In order to better respond to
your request for assistance.
Page 3