Kleenmaid DW6010 User manual

Technical component data
WASH PUMP
Centrifugal pump driven by a single phase induction motor with a permanent capacitor.
Power supply voltage and frequency 220-240 V +/- 10% - 50 Hz
Operation Intermittent
Insulation Class F
Power 150 Watts
Speed (empty) 2950 rpm
Capacitor (VI 450) 6 µF
Primary coil resistance (20°C) 44 Ohms +/- 7%
DRAIN PUMP
Centrifugal pump driven by a single phase induction motor with shading coil
Power supply voltage and frequency 220-240 V ± 10% -
50 Hz
Power 34/30
Watts
Coil resistance (20°C) 155/170
Ohms ± 10%
Max head
1 m
Max capacity
20 litres/min
WATER LOADING SOLENOID VALVE
Power supply voltage and frequency 220-240 V ± 10% -
50/60 Hz
Min/Max operating pressure 0.5 –
10 bar
Rated 3.5 +/-
7% litres/min
Thread dimension
¾ gas
ALTERNATING WASH VALVE
Power supply voltage and frequency 230V -
50Hz
115V -
60Hz (U.S.A.)
DETERGENT DISPENSER
Power supply voltage and frequency 220-240 V ± 10% -
50/60 Hz
Detergent dispenser capacity
48 cc
RINSE AID DISPENSER
Adjustable dose 1 – 6 / 1 –
4 cm 3
Rinse aid dispenser capacity
140 cm3

HEATING ELEMENT
Supply voltage
230 V (240 V UK)
Power
2040 Watts
Internal resistance (20°C)
29 Ohms ± 10 %
Thermal protector (cut-off) NC 98 +/-
5°C
Thermal fuse 206 +/-
10°C
LEVEL PRESSURE SWITCH
Max contact capacity 250 V
14 (4) A
DOOR MICROSWITCH
Max contact capacity 250 V
14 (4) A
TEMPERATURE PROBE (with electronic timer)
Resistance 25°47000 +/-3950Ohm
30°37500 +/-3060Ohm
40°24900 +/-1830Ohm
50°17000 +/-1190Ohm
60°11700 +/-840Ohm
INDICATOR LIGHT
Supply voltage
230 V
Power
0.5 Watts
SAFETY UNIT MICROSWITCH
Max contact capacity 250 V
3 (4) A
BUTTONS
Max contact capacity 250 V
16 (4) A
INTERFERENCE SUPPRESSOR FILTER
Capacitor 1 x 0.1 uF (X1) + 2 x 2700 pF (Y)
Resistance 2.2
MOhms

New wash tank
The differences from the previous tub are the new tub bottom and a modified back.
The tub is constructed in 3 PARTS joined by beads:
- ROOF (aisi 430 stainless steel)
SIDE/REAR/SIDE (aisi 430 stainless steel)
- BOTTOM (aisi 304 stainless steel)
DETAIL OF TUB BOTTOM REAR DETAIL

Tank bottom and stainless steel filter
THE TUB BOTTOM
1= slopes steeply towards the
filter to accelerate the flow of
water towards the sump/pump.
2= has a deep stainless steel
filter zone hopper to improve the
seal.
3= has an inner border to stiffen
the sump fixing zone.
THE FILTER
4= has a "minimum radius"
border to minimise the collection
of residues between the filer and
the bottom.

Tank inner parts
1= the feed pipe to the spray
arms is attached to the filter
sector and to the upper spray
arm feed nozzle.
The roof spray arm feed pipe
is connected to a metal
bracket attached to the tub
roof.
2= single filter sector
between orbital and standard
spray arms (both in plastic).
3= Upper spray arm feed
nozzle attached to metal
bracket fixed to the casing.

Spray arms and relative feed pipes
NEW STANDARD SPRAY ARM IN PLASTIC
CURRENT STANDARD SPRAY ARM
1= ALTERNATE + ROOF: UPPER SPRAY ARM + LOWER SPRAY ARM - NO ROOF
2= UPPER SPRAY ARM + LOWER SPRAY ARM + ROOF
3= ALTERNATE - NO ROOF
4=ROOF-UPPER SPRAY ARM
5= ROOF-UPPER SPRAY ARM
6= UPPER SPRAY ARM
A = FRONT VIEW.
B REAR VIEW

Baskets
baskets upper and lower :
grey stainless steel
upper basket:
- fixed basket
-fully adjustable basket with 3 levels (according to
models - interchangeability)

Inner door liner - detergent distributor - door lock
INNER DOOR LINER IN AISI 304 STAINLESS STEEL
1= LOCK WITH 1 MICROSWITCH
2= DISTRIBUTOR WITH RAST CONNECTOR