Knightsbridge GU10SPIKE Instruction Manual

1
INSTALLATION & MAINTENANCE MANUAL
GU10SPIKE / GU10SPIKEBK / GU10SPIKEL
ACCESSORIES LTD 02
GU10 -35w
IP
65
ML Accessories Limited
LU5 5TA
www.mlaccessories.co.uk 09/2013_V1
INSTALLATION & MAINTENANCE MANUAL
GU10SPIKE. GU10SPIKEBK. GU10SPIKEL
230V
50Hz
IP
65
dim
02
GU10 IP65 GARDEN SPIKE
GU10SPIKE_INSTRUCTIONS_Layout 1 15/10/2013 10:51 Page 1

2
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
GU10SPIKE / GU10SPIKEBK / GU10SPIKEL
GENERAL INSTRUCTIONS
INSTALLATION
SAFETY
• Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable
IP rated junction boxes should be used where required
• The power source connections should be local and accessible via a suitable IP rated enclosure
• Choose a position for the luminaire ensuring that the ground is suitable to hold the spike and luminaire
firmly in position. Check that the ground is not liable to flooding and the spike does not infringe with any
underground pipes or cables
• The body of the product should not rest directly on the ground
• The pre-installed cable supplied is for above-ground use only. Cables that are to be routed within walls or
below ground must be protected by means of suitable conduit or trunking (see Fig. 1)
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is Class I and must be earthed
• This product is IP65 rated
Fig. 1

• Connect the luminaire to the mains supply ensuring that correct polarity is observed: L - Live (brown),
E - Earth (green/yellow), N - Neutral (blue)
• Unscrew the bezel from the fitting, insert a suitable GU10 lamp and replace the bezel carefully ensuring
the gasket is not damaged, is intact, and the bezel is tight to form a weatherproof seal
• Switch on and check for correct operation
3
ADDITIONAL ACCESSORIES
GENERAL
This product should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may
damage the product.
Do not use any source of high-pressure washers to maintain or clean this product.
This product is not suitable for installation in or near a coastal or marine environment.
A light film of acid-free oil is recommended after installation and maintained periodically (2-3 times a year) to
aid corrosion prevention (GU10SPIKE / GU10SPIKEL only).
WARRANTY
This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance
with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch
code will invalidate the warranty. If this product should fail within its warranty period it should be returned
to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for
any installation costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
Code Finish Spike length
EXT2 Stainless Steel 600mm
EXT3 Black 604mm

ML Accessories Limited
LU5 4LT
www.mlaccessories.co.uk DCDEC19_V3
ACCESSORIES LTD
4