Koala Kare KB-300-05-SS Installation instructions

KB300-SS
Surface-Mounted
Baby Changing Station
Cambiador Plegable
Table à Langer
Babywickelstation
Important. Retain for future reference. Read carefully.
Importante. Guárdelo para futuras consultas. Leer atentamente.
Important. À conserver pour de futurs besoins de reference. À lire attentivement.
Wichtig. Zur späteren bezugnahme aufbewahren. Bitte sorgfältig durchlesen.
Koala Kare Products
Installation & Operations Instructions
The KB300-SS Baby Changing Stations have been designed to meet the following applicable provisions of
the 2010 ADA Standards (ADAS) and the 2009/2017 International Code Council (ICC) A117.1 Standards when
properly installed and maintained. To comply with these accessibility requirements the unit must be installed
in a compliant location and height in accordance with the installation instructions.
You are responsible for the safe operation of this unit.

3
KB300-SS
Operations Instructions
3
Please Note
To assure proper installation, it is suggested that
a qualified person or carpenter install the Koala
Baby Changing Station. Koala Kare Products will
not be responsible if the station is not installed
properly. Koala Baby Changing Stations have
been tested to hold a substantial static load.
The unit must be attached to a permanent wall
that is capable of holding a substantial load. The
maximum recommended total weight for this baby
changing station (including baby and parcel bag) is
50lbs. Excessive weight may cause a hazardous or
unstable condition to exist.
Inspection Criteria
A properly maintained baby changing station:
• Opens and closes smoothly.
• Has a functioning strap and buckle. Strap is held
firmly in place when buckle is depressed over it.
• Oers parents liners through a fully stocked liner
dispenser. (Dispenser built into unit.)
• Provides a clean, convenient place for customers
to attend to their children.
Restraint System
Check strap by releasing the lever on the buckle and
pulling one end of the strap up through the bottom
of the buckle, depressing the lever when the strap is
tight. Give the strap a tug in the horizontal direction
away from the buckle, checking that the strap
remains in place beneath the buckle. To loosen the
strap, release the lever and pull the strap from the
bottom of the buckle.
Cleaning and Maintenance
We recommend that the surface of the unit be
cleaned prior to disinfecting. Use a clean nylon
brush or a rag to loosen and remove soil from
the textured surfaces. We recommend that you
use disinfectants and detergents that do not
contain overwhelming fragrances that can mask
inappropriate smells.
ASTM F2285-04 (2016)
WARNING: Never leave child unattended.
WARNING: Avoid serious injury from falling or
sliding out. Always use restraint system.
WARNING: Designed for Infants Only. Age up
to 3.5 years and weighing less than 50 lb (22.7
kg). Keep one hand on the child at all times.
WARNING: Parcels or accessory items, or
both, placed on the unit may cause the unit to
become unstable.
Replacement Parts
For a detailed instructions and a list of replacement
parts for this product, (such as straps, shocks and
labels)
Replacement parts and additional liners can be
purchased from your local distributor
ADA Requirements
Additional information on how this product
complies with ADA requirements can be found
in the KB300 & KB301 Baby Changing Stations
Accessibility Compliance document

4
KB300-SS
Installation Instructions
Tools Needed
1/4" x 3"
Pan Head Wood Screws
Quantity: 6
8-32" x 5/16"
Flange Button Phillips Head Screws
Quantity: 4
Hardware Provided
*Diagrams are not to scale.
Safety Gloves Wall Stud FinderDrill Measuring TapePencil Level
9/32" x 7/8"
Flat Head Phillips Screws
Quantity: 3
Safety Glasses 1/8" (3mm)
(regular & masonry)
drill bits
Phillips Head
Screwdriver
7/32" (6mm)
(regular & masonry)
drill bits
4

5
KB300-SS
Installation Instructions
Step 1:
• Inspect contents and remove changing station from the
shipping container and check for any freight damage. If
damage is found, please call Koala Kare Products’
Customer Service
• Identify the best location for installing the unit.
Step 2:
• Remove the bed and chassis from the box. Open the
main unit by pulling up on the frame and remove the
plastic liner dispenser. Set it to one side. Fig. 1
• Make sure you have taken into consideration the
operating clearance of 9 3/8" (238mm) on both sides
of the exposed chassis and 21 1/8" (537mm) from wall
surface when open.
For Wood Stud Wall
• Measure from the floor 37 7/16" (951mm) on stud center
and mark the wall. The mounting holes are designed for
16" (406mm) stud centers. Ensure the locations you have
marked for the mounting holes are level before drilling.
Fig. 2 Drill pilot holes for keyhole mounting using a 1/8"
regular drill bit.
• If the wall has wooden studs that are not on 16"
(406mm) centers, you will need to use toggles to secure
one side of the unit. The other side should be secured
to the stud using the screws provided. You must allow
for space inside the wall for the toggles to turn. This will
vary depending on the toggles used.
For Masonry or Tile over Stud Wall
• Use a 7/32" (5mm) masonry drill bit for the pilot hole
until you hit the stud. Change bit to 1/8" (3mm) regular
drill bit.
For Metal Stud or Concrete Block
•If the wall has metal studs or an underlying surface of
concrete block, you will need to use toggles to secure
one side of the unit. The other side should be secured to
the stud using the screws provided. You must allow for
space inside the wall for the toggles to turn. This will vary
depending on the toggles used.
*Diagrams are not to scale.
Fig. 1
Fig. 2
16"
(406mm)
37 7/16"
(951mm)
5

6
KB300-SS
Installation Instructions
Step 3:
• Mount bed and chassis by screwing two of the mounting
screws into the pilot holes leaving 1/4" (6.4mm) exposed
to allow keyhole slots to be easily mounted over the
screw heads. Fig. 3
• Place chassis over screws. Fig. 4
• After securing the unit using the keyhole slots, verify
that the unit is level. Tighten top two screws so that they
are flush with the wall.
• Use the four lower holes as a guide to mark and drill
pilot holes. Use remaining four screws and four washers
to complete installation of bed and mounting bracket.
Insert washers over lower four screws. Fig. 5
• All six screws and four washers must be properly
mounted to the chassis.
Step 4:
• To install liner dispenser ensure liner dispenser is free
from damage. Remove key, unlock, and open liner
dispenser lid. This will expose liner dispenser mounting
holes.
• Line up dispenser mounting holes onto chassis and
secure with the four screws provided. Fig. 6 Close and
lock the liner dispenser door.
Step 5:
• Clean work area and inspect unit to ensure it opens and
closes smoothly.
*Diagrams are not to scale.
Fig. 3
Fig. 4
Fig. 5
Fig. 6
1/4"
(6.4mm)
6

7
KB300-SS
Installation Instructions
Step 6:
• To install the bag hook, measure up 44" (1118mm) from
finished floor in the desired location and mark the wall.
• Position the bag hook on the wall so that the top of the
mounting plate is level with the 44" (1118mm) mark.
• Position the bag hook over a wall stud for optimal
strength.
• Mark then predrill the mounting holes. Fig .7
• Use the provided screws to secure the bag hook in
position, then take the escutcheon plate and screw it
over the mounting plate to cover the mounting screws.
Fig. 8
*Diagrams are not to scale.
Fig. 7
Fig. 8
7