Koala Kare KB100-ST User manual

Horizontal Recessed Mounted Baby Changing Station
KB100-ST and KB110-SSRE
INSTALLATION INSTRUCTIONS
Please Note:
To assure proper installation,
it is suggested that a qualified
person or carpenter install the
Koala Baby Changing Station.
Koala Kare Products will not
be responsible if the station is
not installed properly.
Koala Baby Changing
Stations have been tested
to hold a substantial static
load. The unit must be
attached to a permanent wall
that is capable of holding a
substantial load.
Tools Needed:
Measuring Tape• Level• Flat Head and Phillips• Screwdrivers
Stud Finder• Pencil• Drill• 7/32” (.56 cm) Drill Bit• (regular and masonry)
1/8” (.32 cm) Drill Bit• (regular and masonry)
½” (1.27 cm) Drill Bit• (regular and masonry)
Hardware Supplied:
Four ¼” x 3” (.64 cm x 7.62• cm) Panhead Wood Screws
Four ¼” x 3” (.64 cm x• 7.62 cm) Phillips Panhead
Machine Screws
Four ¾” x ¼” (2 cm x .64• cm) Hole Washers
Four Toggles• One Restroom Sign•
You are responsible for the safe operation of this unit.
Inspection Criteria:
A properly maintained unit:
Opens and closes smoothly.• Has both ends of a functioning, non-frayed• strap: buckle clicks when closed and strap is
attached at both ends of the unit.
Offers parents liners through a fully stocked• liner dispenser. (Dispenser is built into unit.)
Provides a clean, convenient place for• customers to attend to their children.
Horizontal Strap (885)• Horizontal KB100-ST Gas Shock (874)• Horizontal KB110-SSRE Gas Shock (875)• Cream Horizontal Liner Dispenser Lid (829)• Grey Horizontal Liner Dispenser Lid (828)• Koala Restroom Door Decal (841)• Warning Label (975)• Cream Unit End Caps (692)• Grey Unit End Caps (850)• Box of Liners (KB150-99)•
Your unit can be installed to meet ADA regulations when and where applicable.
Refer to Federal Register, Volume 56, No. 144 28 CFR Part 36.

Using Toggles
A. Insert Toggle in hole. B. Pull ring and push cap
tightly against wall.
C. Snap off straps. D. Install unit using
screws and washers.
Step 1.
Remove changing station from the shipping container and check for
any freight damage. Identify the best location for installing the unit.
Hold the unit in place and open the bed. Make sure you have taken
the operating clearance into consideration.
Step 2.
Select the wall area where the unit will be installed. Measure from the
floor 44” (111.8 cm) on stud center and mark the wall. Hold the unit
in place to verify the alignment. Mark rough opening 35½”” W x 20¼”
H (90.2 cm x 51.4 cm) and cut a hole in the wall. Construct mounting
frame as indicated in the illustration. If the wall surface is masonry or
tile over wood studs, use caution when cutting rough opeining.
Step 3.
The unit will be mounted using four ¼” x 1½” (.64 cm x 3.84 cm)
wood screws through side holes as shown in illustration.
Step 4.
Place the unit into the recessed area and insert the screws and flat
washers to hold the unit in place. It may be necessary to adjust the
level of unit by using a shim on the top right or left side of the unit
before tightening securely to the studs.
Step 5.
Position Koala sign (supplied) on the outside of the restroom door. Fill
the built-in dispenser with sanitary bed liners. Replacement parts and
additional liners can be purchased from your local distributor.
Using Restraint System
To fasten the waist restraint strap, place strap around child’s midsec-
tion, and push spring tabs into buckles until both spring tabs lock in
place with an audible “click”. Straps can be adjusted to make strap
tighter or looser as required.
Koala Kare Products
A Division of Bobrick
6982 S. Quentin St.
Centennial, CO 80112
© 2008 Koala Kare Products, Form No. AB00x July 2008
Horizontal Recessed Mounted Baby Changing Station
KB100-ST and KB110-SSRE
INSTALLATION INSTRUCTIONS