Koala Kare KB200-SS Owner's manual

The trusted independent experts for hand dryers
and washrooms since 2012.
[e-mail] | 0114 3540047 | 7 Riverside Court, Don Road, Sheffield S9 2TJ

KOALA KARE PRODUCTS
Installation and Operation Instructions
KB200-SS
Baby Changing Station
Cambiador Plegable
Table à Langer
Babywickelstation
Your unit should be installed to meet 2010 ADA Standards for Accessible Design when and where applicable.
You are responsible for the safe operation of this unit.
IMPORTANT. RETAIN FOR FUTURE REFERENCE. READ CAREFULLY.
IMPORTANTE. GUÁRDELO PARA FUTURAS CONSULTAS. LEER ATENTAMENTE.
IMPORTANT. À CONSERVER POUR INFORMATION. À LIRE ATTENTIVEMENT.
WICHTIG. ZUR SPÄTEREN BEZUGNAHME AUFBEWAHREN. BITTE SORGFÄLTIG DURCHLESEN.

KB200-SS Operating Instructions
Please Note: To assure proper installation, it is suggested that a qualified person or carpenter install
the Koala Baby Changing Station. Koala Kare Products will not be responsible if the station is not
installed properly.
Koala Baby Changing Stations have been tested to hold a substantial static load. The unit must be
attached to a permanent wall that is capable of holding a substantial load.
Inspection Criteria:
A properly maintained baby changing station:
• Opens and closes smoothly
• Offers parents liners through a fully stocked liner dispenser. (Dispenser built into unit.)
• Provides a clean, convenient place for customers to attend to their children.
Tools Needed
Hardware Provided
7/32" (6 mm)
(regular &masonry)
drill bits
1/8" (3 mm)
(regular &masonry)
drill bits
four ¼" flat washers
gloves safety glasses level
drill measuring
tape
stud finderpencil
Phillips head
screwdriver
six ¼" x 3" Phillips
panhead wood screws
½" (13 mm)
(regular &masonry)
drill bits
four 8-32" x 5/16" flange
button Phillips head screws

bed and metal
mounting chassis
wall mount liner dispenser
keyhole slot
KB200-SS Installation Instructions
Horizontal Surface Mounted Baby Changing Station
Step 1. Inspect Contents
Remove changing station from the shipping container and check for any freight damage. If
damage is found, please call Koala Kare Products’ Customer Service at 888.733.3456. Gently
and slowly peel back plastic coating to inspect the stainless surface. Verify there is no damage
to the stainless panel before installing. Remove “Installation Kit” and “Operator Kit” from box.
Please give “Operator Kit” to facility manager or operator. Box should contain two pieces: the
bed and metal mounting chassis and the wall mount liner dispenser. Identify the best location
for installing the unit.
2

16"
(406.4mm)
9
1/2
"
(241mm)
9
1/2
"
(241mm)
23
3/16
"
(589mm)
Frame is equipped
with keyhole slots
to assist with
mounting.
KB200-SS Installation Instructions
3
Top two screws at
42¼” (107 cm) to
meet ADA Height
Requirements
Floor
Step 2. Prepare Mounting Surface
Please identify the appropriate hardware for the
mounting surface.
For Standard Installation
Remove the bed and chassis from the box and
select the wall area where the unit will be installed.
Make sure you have taken into consideration the
operating clearance of 24.1 cm on both sides of
the exposed chassis and 58.9 cm from wall surface
when open. Measure from the floor 107 cm on
stud center and mark the wall. The mounting holes
are designed for 40.6 cm stud centers. Ensure the
locations you have marked for the mounting holes
are level before drilling. Drill pilot holes for keyhole
mounting using a 3 mm regular drill bit.
For Masonry or Tile over Stud Wall
Use a 5 mm masonry drill bit for the pilot hole until you
hit the stud. Change bit to 3 mm regular drill bit.
For Metal Stud or Concrete Block
If the wall has wood studs that are not on 40.6 cm
centers, has metal studs or an underlying surface of
concrete block, drill with a 12 mm masonry bit. (You
may have to purchase toggles before installing.)
You must allow a minimum of inside wall space for
toggles to turn depending on toggles used. Insert
and tighten toggles.

Step 3. Mount Bed and Chassis
Use only screws and hardware appropriate for
the type of wall where the baby changing station
is being mounted. Tighten top two screws so that
they are flush with the wall. Use the four lower
holes as a guide to mark and drill pilot holes.
Use remaining four screws and four washers
to complete installation of bed and mounting
bracket. Insert washers over lower four screws. All
SIX screws and four washers must be mounted to
the chassis.
Step 4. Install Liner Dispenser
Ensure liner dispenser is free from damage.
Remove key, unlock, and open liner dispenser
lid. This will expose liner dispenser mounting
holes. Line up dispenser mounting holes
onto chassis and secure with the four screws
provided. Close and lock the liner dispenser door.
Step 5. Complete Installation
Inspect unit to ensure it opens and closes
smoothly. Clean gently with a stainless
steel cleaner, following the manufacturer’s
recommended cleaning instructions. Clean
work area. Give Operator Kit and key to the
facility operator. Replacement parts and
additional liners can be purchased from
your local distributor or by calling Koala at
1.303.539.8300.
Before mounting this changing station, ensure
the wall surface where the unit will be mounted
can support a maximum weight of 150 kg.
KB200-SS Installation Instructions
4
Important:
In Step 3, SIX screws must be mounted to the
chassis to ensure proper load bearing capacity!
Use only screws and hardware appropriate for the
type of wall where the baby changing station is
being mounted.

KB200-SS EN 12221:2008+A1:2013
ENGLISH
WARNING: Do not leave the child unattended.
All assembly fittings shall always be correctly tightened and checked regularly.
Be aware of the risk of open fire and other sources of strong heat, such as electric bar fires,
gas fires, etc. in the near vicinity of the changing unit.
Do not leave the child unattended. The changing unit is intended for infants age up to 12
months, with a maximum weight of 11kg. Do not use changing unit if any parts are broken or
missing.
A changing pad is not required for this product.
Additional or replacement parts shall only be obtained from the manufacturer or distributor.
Unit should be cleaned once or more daily with a clean nylon brush and spray disinfectant.
ESPAÑOL
ADVERTENCIA: Nunca deje al niño solo en el cambiador.
Todos los accesorios del montaje deben ajustarse perfectamente y revisarse periódicamente.
No olvide el riesgo de incendio que la presencia de fuego u otras fuentes de calor, como estufas
eléctricas, de gas, etc. en las proximidades del cambiador puede suponer.
Límpielo y desinféctelo una vez al día o más, según la frecuencia de uso.
Nunca deje al niño solo en el cambiafor. La unidad está diseñada para bebés de hasta 12 meses
de edad, con un peso máximo de 11kg.
Las piezas de repuesto o adicionales solamente deberán adquirirse al fabricante o distribuidor.
No utilice el cambiador si faltan piezas o alguna pieza está rota.
o deje nunca al niño desatendido.
5

KB200-SS EN 12221:2008+A1:2013
6
FRANÇAIS
ATTENTION: Ne laissez pas l’enfant sans surveillance.
Tous les éléments d’assemblage doivent être correctement fixés et vérifiés régulièrement.
Faites attention aux risques présentés par un feu ouvert ou des sources de chaleur telles que
des radiateurs électriques ou des cheminées à gaz à proximité de la table à langer.
Nettoyez et désinfectez la table une fois par jour ou plus en fonction de la fréquence
d’utilisation.
Ne jamais laisser l’enfant sans surveillance conforme aux exigencies de securite. Pour enfants
jusqu’à 12 mois et d’un poids maximum de 11kgs.
Les pièces de rechange ou supplémentaires doivent provenir du fabricant ou du distributeur
uniquement.
N’utilisez pas la table à langer si l’une des pièces est endommagée ou manquante.
DEUTSCH
WARNUNG: Das Kind nie unbeaufsichtigt lassen.
Alle Montageteile müssen stets richtig angezogen und regelmäßig überprüft werden.
Achtung: Bei offenem Feuer und anderen starken Hitzequellen, wie z. B. Heizsonnen, Gasofen
usw., in der Nähe der Wickeltisch besteht Brandgefahr.
Je nach Häufigkeit der Verwendung mindestens einmal täglich reinigen und desinfizieren.
Das kind nie unbeaufsichtigt lassen. Der Wickeltisch ist für Kinder bis zu 12 Monaten mit ei-
nem Maximalgewicht von 11 kg bestimmt.
Zusätzliche Teile oder Ersatzteile sollten nur vom Hersteller oder einem Fachhändler bezogen
werden.

KB200-SS Instrucciones de Uso
Atención: Para garantizar una instalación correcta, se sugiere que una persona capacitada o un carpintero
instale el cambiador de pañales Koala Baby Changing Station. Koala Kare Products no se responsabilizará si el
cambiador no se ha instalado adecuadamente.
Las bases para el cambiador de pañales Koala Baby Changing Station se han probado para garantizar que
soportan un peso estático considerable. La unidad debe ponerse en una pared inmóvil capaz de soportar un
peso considerable.
Criterios de inspección:
Un cambiador de pañales bien mantenido:
• Se abre y se cierra sin problemas.
• Ofrece a los padres forros mediante un dispensador que se halla muy bien provisto. (El dispensador está
incorporado a la unidad).
• Proporciona un lugar limpio y cómodo para que los clientes puedan atender a sus niños.
Herramientas Necesarias
Materiales Suministrados
guantes lentes de seguridad nivel
taladro
cinta
métrica
broca de 7/32"
(6 mm) (normal
y de mampostería)
broca de 1/8"
(3 mm) (normal
y de mampostería)
cuatro arandelas planas
de ¼" (6,3 mm)
detector
de tacos
lápiz
destornillador
de estrella
seis tornillos de estrella
avellanados para madera de
¼" x 3" (6,3 mm x 76,2 mm)
broca de ½"
(13 mm) (normal
y de mampostería)
cuatro tornillos con cabeza abridada de
estrella de 8-32 x 5/16" (8 mm)

chasis de montaje de
base y metal
dispensador de forros de pared
ranura de agujero de cerradura
KB200-SS Instrucciones de Instalación
Cambiador Montado en Superficie Horizontal
Paso 1. Inspeccione el contenido
Saque la base del cambiador de pañales de la caja de embalaje y compruebe que no haya
sufrido daños durante el transporte. Si observa daños, póngase en contacto con el Servicio
de atención al cliente de Koala Kare Products en el 888.733.3456. Retire el plástico protector
despacio y con cuidado para inspeccionar la superficie de acero inoxidable. Compruebe que no
existen daños en el panel de acero inoxidable antes de instalarlo. Retire de la caja el “Paquete
de instalación” y el “Paquete del operario”. Entregue el “Paquete del operario” al responsable
u operario de la instalación. La caja debe contener dos piezas que incluyen la cama y el chasis
de metal de montaje y el dispensador de pared. Localice el mejor lugar para instalar la unidad.
8