Kobalt KB-PPK18 User manual

1
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our
customer service department at 1-888-3KOBALT (1-888-356-2258), 8 a.m - 8 p.m., EST,
Monday - Sunday. You could also contact us at [email protected].
ATTACH YOUR RECEIPT HERE
ITEM #0888116
20 PC POLY PEGBOARD
ORGANIZER KIT
KOBALT and logo design are trademarks or
registered trademarks of LF, LLC. All rights reserved.
MODEL #KB-PPK18
KB-PPK18

2
TABLE OF CONTENTS
Package Contents...........................................................................................................................3
Hardware Contents.........................................................................................................................4
Safety Information. .........................................................................................................................5
.
Preparation ....................................................................................................................................5
Assembly or Installation Instructions .............................................................................................6

PACKAGE CONTENTS
3
PART DESCRIPTION QUANTITY
A Poly Pegboard 2
B ¼” to ½” Spring Clip 2
C 1” Single Rod 2
D 2 ½” Single Rod 4
E 4” Single Rod 3
F 2 ¼” Curved Hook 2
G 2 ¾” Double Rod 2
H 5” Double-Closed Loop 2
I Multi-Prong Tool Holder 1
PART DESCRIPTION QUANTITY
A
E
D
B
G
H
I
C
F

4
HARDWARE CONTENTS (shown actual size)
Wall Spacer
2” Screw Wall Anchor
¼” Hook Screw
AA BB CC DD

5
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the
product.
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble the product.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Drill, 5/16” drill bit, screwdriver, level, pencil
PREPARATION

ASSEMBLY INSTRUCTIONS
6
1. Position the first pegboard in your desired
location and make sure it is level.
For installation with optional K-Rail go to page 5
K-rails sold separately
Hardware Used
BB x 2
2” Screw (Optional)
2. While holding the pegboard in place, mark a
line on your wall down the right side of the
pegboard, then mark the center of the
pegboard holes on your wall. Tip: You can
omit drawing the line down the right side of the
pegboard and install temporary screws into the
1st pegboard to hold it in position so you can
align the 2nd pegboard up to it and mark the holes.
1
2

ASSEMBLY INSTRUCTIONS
7
3. If you didn’t follow the tip in step 2, line up
the next pegboard on the right side of the
line you marked on your wall in Step 2
and mark the holes. Make sure to use the
left side of your line for a tight fit between
the pegboards.
Hardware Used
CC x 18
Wall Anchor
Hardware Used
AA x 18
Wall Spacer
4. Using a 5/16” drill bit, drill all 18 of the
marked holes on your wall. Make sure to
keep your drill straight and steady for a tight
wall anchor fitting. After your holes are
drilled, lightly tap the wall anchors all the
way in.
5. Insert a screw and wall spacer into each
hole on both pegboards. 5
BB 2” Screw x 18

ASSEMBLY INSTRUCTIONS
8
6. Bring the pegboard up to your wall and align
each screw to the wall anchor. Get them all
started by hand with a few turns, then go
back and screw them in. Tip: Do not tighten
them all the way until you have the 2nd
pegboard up in the same fashion. This will
allow a little bit of wiggle room as you are
tightening the screws to make sure the
seam down the middle of the pegboards is tight.
Hardware Used
7. Install hooks in desired locations using the
hook screws. 7
Screw locks
hook in place
Tab locks into
pegboard
D
O
U
B
L
E
L
O
C
K
I
N
G
S
Y
S
T
E
M
K
E
E
P
S
H
O
O
K
S
&
T
O
O
L
S
I
N
P
L
A
C
E
1 2
AA x 18
Wall Spacer
BB 2” Screw x 18

ASSEMBLY INSTRUCTIONS FOR OPTIONAL K-RAIL
9
1. See instructions included with the K-Rail
for installation before proceeding to step 2.
2. You will need (2) K-rail to complete this
assembly method. One K-rail to act as the
lower support and the other as an upper
support. At 32” in length, the K-rail is
perfectly suited to hold the (2) 16”W x 22”H
pegboards side-by-side. Position the lower
K-rail in your desired location, ensure it is
level and then secure to the wall per the
K-rail installation instructions.
(Note: apply enough torque to countersink
the installation screws into the K-rail to
avoid interference with the pegboard.)
3. Once you have the bottom K-Rail installed,
set the pegboards in the K-Rail groove and
lean them up against the wall and mark the
center of the pegboard holes on your wall.
3
2

ASSEMBLY INSTRUCTIONS
10
4. Now place the upper K-rail on top of the
pegboards and secure to the wall per the
K-rail installation instructions. You will only
be able to secure along the upper portion
of the K-rail during this step.
5. Carefully bend the pegboards out of the
top K-Rail as shown and set aside. 5
Hardware Used
DD
x 3
K-Rail Screws
Hardware Used
x 3
K-Rail Screws
6. With pegboard removed from the K-rails,
complete installation of the upper K-rail by
securing the lower portion per the K-rail
installation instructions. Make sure to
counter-sink the screws in this lower section
so they do not interfere with sliding the
pegboards in.
4

ASSEMBLY INSTRUCTIONS
11
7. Using a 5/16” drill bit, drill all 12 of the
marked holes on your wall for the pegboard
wall anchors. After holes are drilled, lightly
tap the wall anchors flush to the wall.
Hardware Used
AA x 18
Wall Spacer
8. Insert a screw and wall spacer in the holes
on both pegboards. Set the depth and
angle of the screw.
9. Carefully set the first pegboard in the lower
K-Rail track and bend the board at the top
into the upper K-Rail track. Now align each
screw into the wall anchor and get them all
started by hand with a few turns, then go
back and screw them in.
Tip: Do not tighten them all the way until you
have the 2nd pegboard up in the same
fashion. This will allow a little bit of wiggle
room as you are tightening the screws to
make sure the seam down the middle of
the pegboards is tight.
8
8
BB 2” Screw x 18
Hardware Used
CC x 6
Wall Anchor
Hardware Used
AA x 6
Wall Spacer
BB 2” Screw x 6

12
Printed in China
Screw locks
hook in place
Tab locks into
pegboard
D
O
U
B
L
E
L
O
C
K
I
N
G
S
Y
S
T
E
M
K
E
E
P
S
H
O
O
K
S
&
T
O
O
L
S
I
N
P
L
A
C
E
1 2
ASSEMBLY INSTRUCTIONS
9. Carefully set the first pegboard in the lower
K-Rail track and bend the board at the top
into the upper K-Rail track. Now align each
screw into the wall anchor and get them all
started by hand with a few turns, then go
back and screw them in.
Tip: Do not tighten them all the way until you
have the 2nd pegboard up in the same
fashion. This will allow a little bit of wiggle
room as you are tightening the screws to
make sure the seam down the middle of
the pegboards is tight.
10.Install peghooks in desired locations using
the hook screws. K-rail accessories
(not included) can be added to either the
upper/lower K-rail as desired.
10
Hardware Used
AA x 18
Wall Spacer
BB 2” Screw x 18
Hardware Used
DD x 21
1/4” Hook Screw

1
Número de serie Fecha de compra
¿Preguntas, problemas, piezas faltantes? Antes de volver a la tienda, llame a nuestro
Departamento de Servicio al Cliente al 1888-3KOBALT (1-888-356-2258), de lunes a domingo
de 8 a.m. a 8 p.m., hora estándar del Este. También puede ponerse en contacto con
nosotros en [email protected].
ADJUNTE SU RECIBO AQUÍ
ARTÍCULO #0888116
KIT ORGANIZADOR PARA TABLERO
PERFORADO DE POLIETILENO DE 20 PIEZAS
KOBALT y el diseño del logotipo son marcas comerciales o
marcas registradas de LF, LLC. Todos los derechos reservados.
MODELO #KB-PPK18
KB-PPK18

2
ÍNDICE
Contenido del paquete....................................................................................................................3
Aditamentos....................................................................................................................................4
Información de seguridad...............................................................................................................5
Preparación....................................................................................................................................5
Instrucciones de ensamblaje o instalación.....................................................................................6

CONTENIDO DEL PAQUETE
3
PIEZA DESCRIPCIÓN CANTIDAD
A Tablero perforado de polietileno 2
B Sujetador de resorte de 6,35 mm a 12,7 mm 2
C Varilla simple de 2,54 cm 2
D Varilla simple de 6,35 cm 4
E Varilla simple de 10,16 cm 3
F Gancho curvo de 5,71 cm 2
G Varilla doble de 6,98 cm 2
H Bucle de doble cierre de 12,7 cm 2
I Soporte para herramientas de
varias puntas 1
PIEZA DESCRIPCIÓN CANTIDAD
A
E
D
B
G
H
I
C
F

4
ADITAMENTOS (se muestran en tamaño real)
Espaciador de pared
Tornillo de 2" Ancla de expansión de pared
Tornillo para gancho de 6,35 mm
AA BB CC DD

5
INFORMACIÓN DE SEGURIDAD
Lea y comprenda completamente este manual antes de intentar ensamblar, usar o instalar el
producto.
Antes de comenzar a ensamblar el producto, asegúrese de tener todas las piezas. Compare las
piezas con la lista del contenido del paquete y la lista de aditamentos. No intente ensamblar el
producto si falta alguna pieza o si estas están dañadas.
Tiempo estimado de ensamblaje: 30 minutos
Herramientas necesarias para el ensamblaje (no se incluyen): taladro, broca para taladro de 5/16",
destornillador, nivel, lápiz
PREPARACIÓN

INSTRUCCIONES DE ENSAMBLAJE
6
1. Coloque el primer tablero perforado en la ubicación
deseada y asegúrese de que esté nivelado.
Para la instalación con riel en forma de K opcional,
vaya a la página 5. Los rieles en forma de K se
venden por separado
Aditamentos utilizados
BB x 2
Tornillo de 2" (opcional)
2. Mientras sostiene el tablero perforado en su lugar,
marque una línea en la pared por el lado derecho
del tablero perforado, luego marque el centro de los
orificios del tablero perforado en su pared. Consejo:
puede omitir la línea por el lado derecho del tablero
perforado e instalar tornillos temporales en el primer
tablero perforado para mantenerlo en su posición de
modo que pueda alinear el segundo tablero perforado
y marcar los orificios.
1
2

INSTRUCCIONES DE ENSAMBLAJE
7
3. Si no siguió el consejo del paso 2, alinee el
siguiente tablero perforado en el lado derecho
de la línea que marcó en la pared en el paso
2 y marque los agujeros. Asegúrese de usar el
lado izquierdo de su línea para un ajuste perfecto
entre los tableros perforados.
Aditamentos utilizados
CC x 18
Ancla de expansión de pared
Aditamentos utilizados
AA x 18
Espaciador de pared
4. Con una broca para taladro de 5/16", taladre los
18 orificios marcados en la pared. Asegúrese de
mantener el taladro recto y estable para un buen
ajuste del ancla de expansión de pared. Después
de perforar los orificios, golpee ligeramente las
anclas de expansión de pared hasta insertarlas
por completo.
5. Inserte un tornillo y un espaciador de pared
en cada orificio de ambos tableros perforados. 5
BB Tornillo de 2" x 18

INSTRUCCIONES DE ENSAMBLAJE
8
6. Lleve el tablero perforado a la pared y alinee
cada tornillo con la ancla de expansión de pared.
Enrósquelos con la mano unas cuantas vueltas,
luego vuelva a atornillarlos. Consejo: no los apriete
del todo hasta que haya colocado el segundo tablero
de perforado de la misma manera. Esto permitirá un
poco de margen de maniobra mientras ajusta los
tornillos para asegurarse de que la unión en el medio
de los tableros perforados esté bien apretada.
Aditamentos utilizados
7. Instale los ganchos en las ubicaciones
deseadas con los tornillos para ganchos. 7
El tornillo bloquea
el gancho en su lugar
La lengüeta se bloquea
en el tablero perforado
1 2
AA x 18
Espaciador de pared
BB Tornillo de 2" x 18
M
A
N
T
I
E
N
E
L
O
S
G
A
N
C
H
O
S
Y
L
A
S
H
E
R
R
A
M
I
E
N
T
A
S
E
N
S
U
L
U
G
A
R
S
I
S
T
E
M
A
D
E
D
O
B
L
E
B
L
O
Q
U
E
O