Kodak PIXPRO AZ527 User manual

User Manual
KODAK
DIGITAL CAMERA
PIXPRO AZ527

ii 1ii 1
Declaration of Conformity
Responsible Party: JK Imaging Ltd.
Address: JK Imaging Ltd., 17239 So. Main Street, Gardena, CA 90248 USA
JK Imaging Europe, 71 Clarendon Road, Watford, WD17 1DS, UK
Company Website: kodakpixpro.com
INDUSTRY CANADA
This device complies with Canadian ISED.
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1)
le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit
accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un
fonctionnement indésirable.
Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in this
manual. The further RF exposure reduction can be achieved if the product can be kept
as far as possible from the user body or set the device to lower output power if such
function is available.
Déclaration d’exposition aux radiations:Le produit est conforme aux limites d’exposition
pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un
environnement non contrôlé.
Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction
aux expositions RF peut être augmentée si l’appareil peut être conservé aussi loin que
possible du corps de l’utilisateur ou que le dispositif est réglé sur la puissance de sortie
la plus faible si une telle fonction est disponible.
Before You Start

2
For Customers in Europe
This symbol [crossed-out wheel bin WEEE Annex IV] indicates separate collection
of electrical waste and electronic equipment in the European countries. Please
do not throw the equipment into domestic refuse. Please use the return and
collection systems available in your country for proper, safe disposal of this
product.
Batteries: Please dispose of used batteries at designated collection centers.
Packaging: Please follow local regulations for the recycling of packaging.
“CE” mark indicates that this product complies with the European requirements
for safety, health, environment and customer protection. “CE” marked cameras are
intended for sales in Europe.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive
2014/53/EU. The following test methods have been applied in order to provepre-
sumption of conformity with the essential requirements of the R&TTE Directive
2014/53/EU:
The frequency and maximum transmitted power in EU are listed as below:
2412MHz~2472MHz (Wi-Fi 2.4GHz) : 19.98dBm
- EN 609501/A12:2011+A2:2013
Safety of Information Technology Equipment
- EN 50566: 2013
Product standard to demonstrate compliance of radio frequency ields from
handheld and body- mounted wireless communication devices used by the
general public (30 MHz — 6 GHz)

3
- EN 622092: 2010
Human exposure to radio frequency ields from handheld and bodymounted
wireless communication devices — Human models, instrumentation, and
procedures
Part 2: Procedure to determine the speciic absorption rate (SAR) for wireless
communication devices used in close proximity to the human body (frequency
range of 30 MHz to 6 GHz)
- EN 300 328 V2.1.1 (201611)
Wideband transmission systems; Data transmission equipment operating in the
2,4 GHz ISM band and using wide band modulation techniques
- Draft EN 301 4891 V2.2.0 (201703)
Electromagnetic compatibility and Radio Spectrum Matters (ERM); Electro
Magnetic Compatibility (EMC) standard for radio equipment and services; Part 1:
Common technical requirements
- Draft EN 301 48917 V3.2.0 2017
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
Part 17: Speciic conditions for Broadband Data Transmission Systems.
Manufacturer: Sintai Optical (Shenzhen) Co., Ltd
Address: Qiwei Ind Sec, 1st, 2nd,& 3RD Bldg, Lisonglang Village, Gongming Town,
Bao’an District, Shenzhen, Guangdong, China
For Customers in the U.S.A.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

4
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modiications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement:
This product complies with the FCC portable RF exposure limit set forth for an
uncontrolled environment and is safe for intended operation as described in this manual.
Additional RF exposure reduction can be achieved if the product can be kept as far as
possible from the user body or set the device to lower output power if such function is
available.

5
About this Manual
Thank you for purchasing the KODAK PIXPRO Digital Camera. Please carefully read this
manual and keep it well for future reference.
JK Imaging Ltd. reserves all rights of this document. No part of this published manual
may be reproduced, transmitted, transcribed, stored in a retrieval system or translated
into any language or computer language, in any form, by any means, without the prior
written permission of JK Imaging Ltd..
All trademarks mentioned in this manual are used for identiication purposes only and
are properties of their respective owners.
This manual provides you with instructions on how to use your new KODAK PIXPRO
Digital Camera. Every eort has been made to ensure that the contents of this manual
are accurate; however JK Imaging Ltd. reserves the right to make changes without
notice.
Throughout this manual, the following symbols are used to help you locate
information quickly and easily:
Indicates useful information.
In the instructions below, the following symbols may be used throughout this manual
on how to operate the camera. This is to facilitate better understanding:
「Item properties」: The optional properties in the camera interface are indicated by
the symbol「」.

6 7
Safety Notes
Do not drop the camera or allow it to hit solid objects.
Do not attempt to disassemble or repair the camera.
Do not use or store the camera in dusty places or on a beach to prevent dust or sand
from entering the camera, causing possible damage to it.
Do not use or store the camera in a hot environment or under direct sunlight.
Do not use or store the camera near a powerful magnetic ield, for example near a
magnet or transformer.
Avoid touching the lens of the camera.
Do not expose the camera to direct sunlight for a long period time.
To prevent the camera from being damaged by moisture, do not use or store the
camera in very humid environments, such as in rain or near bodies of water.
If water accidentally comes in contact with the camera. turn the camera o, remove
the battery and the memory card, and dry it within 24 hours
When you take the camera from a cold place to a warmer environment, condensation
may occur. Please wait for a reasonable period of time before you turn it on.
Before you remove the battery and memory card, the camera should be turned o.
When you clean the body of the camera, don not use abrasive, alcohol-based or
organic cleaner.
Use a professional lens wiping cloth and dedicated cleaner to wipe and clean the lens.
Download your photos and remove the memory card when you are going to store the
camera for a long period of time.
If this camera is not in use for a long time, please keep it in a dry and clean condition.
Our company will not pay compensation for any failure of playback of pictures or
videos caused by improper operation.
Safety notes for this camera

76 7
Safety notes for battery
Please use a battery that is the same type as the one included.
Please use the attached charger to charge the battery.
If battery luid leaks inside the camera, contact our customer service department.
If the battery luid leaks onto your skin, rinse your skin with clean water and seek
immediate medical attention.
Disposal of used batteries shoud be carried out in accordance with local (national or
regional) regulations.
To prevent the battery from being damaged, do not drop the battery or allow it to hit
solid objects or to be scratched by the objects.
Do not let the battery come in contact with metal objects (including coins) to avoid
short circuiting, discharging, excessive heat, or possible leakage.
Do not attempt to disassemble the battery.
Do not expose the battery to water. Always keep the battery contacts dry.
Do not heat the battery or throw it into a ire to avoid a possible explosion.
Do not store the battery in a hot environment or in direct sunlight.
If the battery overheats during charging or use, stop charging or use immediately.
Turn o the product, remove the battery carefully, and wait until it cools down.
When the camera is stored for a long period of time, remove the battery and keep it in
a dry place that is not accessible to infants and children.
In a colder environment, the performance of the battery could be noticeably reduced.
When you install the battery, install it according to the positive and negative markings
on the battery compartment. Never force it into the battery compartment.

8
Safety notes for memory card
We suggest buying only well-known, name brand memory cards to ensure peak
performance.
Format the memory card using the camera before you use it or insert a new one.
Do not drop the memory card or allow it to hit solid objects to avoid damaging it.
Do not attempt to disassemble or repair the memory card.
Do not expose the memory card to water. Always keep it dry.
Do not remove the memory card when the camera is turned on. Otherwise, the
memory card could be damaged.
Do not directly edit the data on the memory card. Copy the data to your PC before
you edit them.
When the camera is stored for a long period of time, be sure to download your photos
and remove the memory card. Store it in a dry environment.
Do not modify the name of the iles or folders of the memory card using your PC.
Modifying the ile names may cause the iles to not be recognized on the camera or a
possible error may occur.
A photo taken with the camera will be stored in the folder that is automatically
generated on the memory card. Do not store photos that are not taken using this
camera in these folders as the pictures cannot be recognized during the playback.
When you insert a memory card, make sure the notch of the card matches the
markings on the top of the card slot.

9
Other Safety Notes
Do not disconnect the power or turn the camera o during the update process. Doing
so may cause incorrect data to be written and the camera may not power on later.
Do not hang the neck strap of the camera around the neck of a child.
When using your camera on an airplane, observe the relevant rules speciied by the
airline.
Due to the limitations of manufacturing technology, the LCD may have a few dead
or bright pixels. These pixels do no eect the quality or performance of the camera,
photos or video.
Do not expose the LCD to water. In a humid environment, only wipe it with a soft and
dry cleaning cloth.
If the LCD screen is damaged, pay particular attention to the liquid crystal in the
screen. If any of the following situations arise, take the recommended immediate
action indicated below:
1. If liquid crystal comes in contact with your skin, please wipe with a dry cloth, wash
thoroughly with soap, and rinse with plenty of clean water.
2. If liquid crystal gets into your eye, lush the eye immediately with plenty of clean
water for at least 15 minutes and then seek for medical assistance.
3. If liquid crystal is swallowed, immediately lush your mouth thoroughly with clean
water and induce vomiting. Seek for medical assistance.