Kodak PIXPRO SL10 User manual

SMART LENS Camera
User Manual

1
EN
About this Manual
Thank you for purchasing the KODAK PIXPRO SMART LENS Camera. Please
carefully read this manual and keep it for future reference.
JK Imaging Ltd. reserves all rights of this document. No part of this published
manual may be reproduced, transmitted, transcribed, stored in a retrieval
system or translated into any language or computer language, in any form, by
any means, without the prior written permission of JK Imaging Ltd..
 Alltrademarksmentionedinthismanualareusedforidenticationpurposes
only and are properties of their respective owners.
This manual is to introduce you how to operate this KODAK PIXPRO SMART
LENS Camera. JK Imaging Ltd. has tried its utmost to ensure the correctness
of all contents here, but reserves the right to modify. All of these contents are
subject to change without prior notice.
Declaration of Conformity
Responsible Party: JK Imaging Ltd.
Address: 1411 W. 190th Street, Suite 550, Gardena, CA 90248, USA
Company Website: www.kodakpixpro.com
In this manual:
The memory card referred to in this manual is a Micro SD Card or Micro SDHC card.

2
EN
INDUSTRY CANADA
This device complies with Canadian RSS-210.
This device complies with Industry Canada license-exempt RSS standard (s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Radiation Exposure Statement:
This product complies with the Canadian portable RF exposure limit set forth for
an uncontrolled environment and is safe for intended operation as described in
this manual. Additional RF exposure reduction can be achieved if the product can
be kept as far as possible from the user body or set the device to lower output
power if such function is available.
For Customers in Europe
This symbol [crossed-out wheel bin WEEE Annex IV] indicates separate
collection of electrical waste and electronic equipment in the European
countries. Please do not throw the equipment into domestic refuse. Please
use the return and collection systems available in your country for proper,
safe disposal of this product.

3
EN
“CE” mark indicates that this product complies with the European
requirements for safety, health, environment and customer protection. “CE”
marked cameras are intended for sales in Europe.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive
1999/5/EC. The following test methods have been applied in order to prove
presumption of conformity with the essential requirements of the R&TTE Directive
1999/5/EC:
- EN 60950-1: 2006+A11:2009 +A1:2010 +A12:2011
Safety of Information Technology Equipment
- EN 50566: 2013
Productstandardtodemonstratecomplianceofradiofrequencyeldsfrom
handheld and body- mounted wireless communication devices used by the
general public (30 MHz — 6 GHz)
- EN 62209-2: 2010
Humanexposuretoradiofrequencyeldsfromhandheldandbodymountedwireless
communication devices — Human models, instrumentation, and procedures
Part2:Proceduretodeterminethespecicabsorptionrate(SAR)forwireless
communication devices used in close proximity to the human body (frequency
range of 30 MHz to 6 GHz)

4
EN
- EN 300 328 V1.8.1 : 2012
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband
Transmission systems; Data transmission equipment operating in the 2.4 GHz
ISM band and using spread spectrum modulation techniques; Harmonized EN
covering essential requirements under article 3.2 of the R&TTE Directive.
- EN 301 489-1 V1.9.2: 2008
Electromagnetic compatibility and Radio Spectrum Matters (ERM); Electro
Magnetic Compatibility (EMC) standard for radio equipment and services; Part 1:
Common technical requirements.
- EN 301 489-17 V2.2.1:2012
Electromagnetic compatibility and Radio spectrum Matters (ERM); Electro
Magnetic Compatibility (EMC) standard for radio equipment and services; Part 17:
Specicconditionsfor2.4GHzwidebandtransmissionsystemsand5GHzhigh
performance RLAN equipment.
For Customers in the U.S.A.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

5
EN
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCCCaution:Anychangesormodicationsnotexpresslyapprovedbythe
party responsible for compliance could void the user’s authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.

6
EN
Radiation Exposure Statement:
This product complies with the FCC portable RF exposure limit set forth for an
uncontrolled environment and is safe for intended operation as described in this
manual. Additional RF exposure reduction can be achieved if the product can be
kept as far as possible from the user body or set the device to lower output power
if such function is available.

7
EN
Safety Notes
Safety notes for this camera
Do not disassemble or repair this camera by yourself.
Do not drop the camera or allow it to hit solid objects.
To prevent the camera from being damaged by moisture, do not use or store the
camera in very humid environments, such as in rain or near bodies of water.
Turn the camera off, remove the battery and the memory card, and dry it within
24 hours if water accidentally comes in contact with the camera.
Do not use or store the camera in dusty places or on a beach to prevent dust
or sand from entering the camera, causing possible damage to it.
Do not use or store the camera in a hot environment or under direct sunlight.
 Pleasedonotuseinplaceshavinghighintensitymagneticeld,electrostatic
and electric wave interference (for example near a microwave oven), which
may cause failure in receiving signals.
Before you remove the battery and memory card, the camera should be turned
off.
Advise to use soft lens cloth to regularly clean the camera’s body and lens mount.

8
EN
In cleaning the camera body, please don’t use corrosive cleaning agents or
those with alcohol or organic solvent.
If this camera is not in use for a long time, please keep it in a dry and clean
condition.
Our company will not pay compensation for any failure of playback of pictures
or videos caused by improper operation.
 Whenusingyourcameraonanairplane,observetherelevantrulesspecied
by the airline.
Do not place the product where it can be reached by infants and children.
Safety notes for battery
Please use a battery that is the same type as the one included.
Please use the attached charger to charge the battery.
If the liquid leaking from the battery contacts with your skin, please immediately
ushwithwaterandseekmedicaltreatment.Iftheliquidleaksintothecamera,
please contact the retailer.
Please dispose of the wasted battery in accordance with local (national or
regional) regulations.
To prevent the battery from being damaged, do not drop the battery or allow it
to hit solid objects or to be scratched by the objects.

9
EN
Do not let the battery come in contact with metal objects (including coins) to
avoid short circuiting, discharging, excessive heat, or possible leakage.
Do not attempt to disassemble the battery.
Do not expose the battery to water. Always keep the battery contacts dry.
 Donotheatthebatteryorthrowitintoaretoavoidapossibleexplosion.
Do not store the battery in a hot environment or in direct sunlight.
If an overheating happens during charging or use, please immediately stop
charging or using and then take out the battery with care in shutdown mode to
wait it for cooling.
If it is not used for a long time, please remove the battery for proper keeping.
In a colder environment, the performance of the battery could be noticeably
reduced.
Safety notes for memory card
A memory card is optional and is not included in the product package. It needs
to be purchased separately. Please use an original memory card which is
Class 4 or higher and has a capacity of 4GB to 32GB.
 Beforeusingabrandnewmemorycard,pleaseformatthememorycardrst.
Do not make the memory card fall off from high places or hit by heavy objects
to prevent damaging it.

10
EN
Do not attempt to disassemble or repair the memory card.
Do not expose the memory card to water. Always keep it dry.
Do not remove the memory card when the camera is turned on. Otherwise, the
memory card could be damaged.
Do not directly edit the data on the memory card. Copy the data to your PC
before you edit them.
When the camera is stored for a long period of time, be sure to download your
photos and remove the memory card. Store it in a dry environment.
 Donotmodifythenameofthelesorfoldersofthememorycardusingyour
PC.Modifyingthelenamesmaycausethelestonotberecognizedonthe
camera or a possible error may occur.
A photo taken with the camera will be stored in the folder that is automatically
generated on the memory card. Do not store photos that are not taken using
this camera in these folders as the pictures cannot be recognized during the
playback.

11
EN
ProductSpecications
Image Sensor 1/2.3” BSI CMOS
Total Pixels 16.76 Megapixels
Effective Pixels 16.35 Megapixels
Focal Length 5.0mm (Wide) ~ 50.0mm (Tele)
35mmlmequivalent 28mm (Wide) ~ 280mm (Tele)
F number F3.2 (Wide) ~ F5.6 (Tele)
Optical Zoom 10x
Focusing Range Normal:(Wide)60cm~∞,(Tele)100cm~∞
Macro:(Wide)5cm~∞
Anti-Handshake Optical Image Stabilization

12
EN
Wi-Fi Yes (802.11 b/g/n)
NFC Yes
Remote Control Yes (via smart device)
File Format Still Image: Exif 2.3 (JPEG)
Movie: MP4 [Image: H.264; Audio: AAC(Stereo)]
Power Rechargeable Li-ion Battery LB-052, 3.7V 880mAh,
In-Camera Charging
Shooting Capability Approx. 200 Shots (Based on CIPA Standards)
Operation
Environment Temperature: 0 ~ 40°C, Humidity: 0 ~ 90%
Dimensions (W×H×D) 59.6×59.6×55.8mm (Based on CIPA Standards)
Weight Approx. 145g (Body only)

13
EN
Getting Ready
Accessories Included
Your camera box should contain the camera model you purchased along with the
following accessories. If anything is missing or appears to be damaged, please
contact your retailer.
▪Rechargeable Li-ion battery
▪AC adapter
▪Micro USB cable
▪Wrist strap
▪User manual
▪Service card
▪Warranty card

14
EN
Part Names

















1 NFC Mark 6 Zoom Lever
2 Power Button 7 Shutter Button
3 Microphone 8 Micro USB Port Cover
4 Wrist Strap Buckles 9 Battery Cover
5 Speaker 10 Tripod Screw Hole
After turning the camera on, you may move the camera's zoom lever to
zoom, and press the shutter button to take photos.

15
EN
Installation of Wrist Strap
It is recommended to use the wrist strap to prevent the camera falling off during
use. Please install it on the camera and then wear it around your hand per the
diagram below.

16
EN
Installing Battery and Memory Card
1. Open the battery cover.
2. Insert the battery into the battery
compartment according to the negative
and positive directions as illustrated in the
picture. Push the battery down until it locks
in place.

17
EN
3. Insert the memory card into the memory
card slot as shown in the diagram. Push
it down until it locks in place.
4. Close the battery cover.
When you insert a memory card,
make sure the notch of the card
matches the markings on the top of
the card slot.
To remove the memory card, press
down on the card slightly to unlock
it and then carefully draw it upwards
withngers.

18
EN
Charging Battery
For charging, you may use the included AC
Adapter and Micro USB cable to charge
the camera when it is off. You also may
connect the Micro USB cable to computer
for charging.
The camera will only charge while
powered off. If the camera is turned
on while connected to power, normal
camera functions will be available for
use, but the camera will not charge
until it is turned off.
Charging indicator
Charging indicator:
Steady orange: Charging.
The indicator will go out
oncechargingisnished,
and the camera will be
powered off automatically.

19
EN
Connect the smart device
Install APP
Download a dedicated installation package from the application store corresponding
to the device (APP name: PIXPRO Remote Viewer) and then install it.
Beforeuse,pleaseconrmthatyoursmartdeviceisasmartphonewith
Android 2.3 or 4.x system, a tablet computer with Android 4.x or is an iOS6/7
system. If not, please upgrade your smart device before using the APP.
Wi-Fi connection (Android system and iOS system)
1. Press the power button to turn the camera on.
2. Enable the Wi-Fi feature of your smart device to automatically search
surrounding hotspots.
3. Select "PIXPRO-SL10_XXXX", and input the eight-digit number password.
(The camera's SSID and password are located on the back side of the battery
cover.)