Kohler Englefield STUDIO 5625A-VS-CP User manual

SPARE PARTS LIST
BEFORE YOU BEGIN
1217518-A02-F 24/06/2019
INSTALLATION
INSTRUCTIONS
TAPWARE
Englefield
STUDIO Dual Rain Shower
ROUGH-IN DIMENSIONS
CONTACT AND WARRANTY INFORMATION
NEW ZEALAND
KOHLER NZ LTD
Free Ph: 0800 100 382
Free Fax: [phone]
www.englefield.co.nz
AUSTRALIA
KOHLER AUSTRALIA
Free Ph: 1 800 ENGLEFIELD
(1 800 364 533)
www.englefield.com
For warranty information, please visit our website
Page 41398217-A02-A 16/07/2019 Englefield
5625A-VS-CP
All information is based on the latest product information available at the time of
publication. Englefield reserves the right to make changes in product character-
istics, packaging, or availability at any time without notice.
Please leave this installation instructions guide for the consumer.
It contain important information.
1. Flush the water supply pipes thoroughly to remove debris.
2. An in-line filter must be used with this product.
3. The highest working pressure for the hand shower and the overhead shower is 500kPa. If it
exceeds 500kPa, a pessure limiting valve must be fitted.
4. The operating temperature of hand shower and the overhead shower is from 10˚C to 70˚C.
NZ building code G12 requires that maximum hot water temperature at any sanitary fixture
used for personal hygiene shall not exceed either 45˚C or 55˚C. If so, a tempering valve must
be installed.
5. This shower is intended for high/mains pressure installations. It may not be suitable for use
with gravity-fed water heaters, low and unequal pressure supplies.
6. All installations should comply with local plumbing codes and the relevant requirements of
AS/NZS 3500 and AS/NZS 6400.
INSTALLATION INSTRUCTIONSSTUDIO Dual Rain Shower
200mm Round Shower Head
1241287
Hand shower (Multi modes)
1397398
Hose washer
1239241
Shower hose
1241297
Elbow
1358461-CP
Shower hose
1241296
Clamp bracket
1241291
Hexagonal wall mount
1241288
Diverter set
1241293
Optional
wall mount
1241289
G 1/2”B
G 1/2”B
225
Ø 50
Ø 90
1524mm / 600mm
G 1/2”
* All measurements shown are in milimetres
1144
847
G1/2”B 1200~1300 Recommended height
to Finished Floor
1012
350 Ø200
55
51
G1/2”
Ø200
1398217-A02-A 16/07/2019

Mounting hole distance: 847 mm
12387
6
5
4
11
9 (Optional)
14
15
17
16
10
12 13
12311
18
CLEANING INSTRUCTIONS
INSTALLATION CHECKOUT
Page 31398217-A02-A 16/07/2019 Englefield
INSTALLATION INSTRUCTIONSSTUDIO Dual Rain Shower
Page 21398217-A02-A 16/07/2019 Englefield
INSTALLATION INSTRUCTIONSSTUDIO Dual Rain Shower
How to Install the Shower Column & Elbow
INSTALLATION
1. Select a location on a vertical wall to install shower column
according to rough-in dimensions.
Note: The column must be fixed to timber studs or
nogs in the wall.
2. Mark the position of top & bottom wall fixing holes on the
wall (Distance: 847mm apart) and then drill a hole at both
positions.
Note: Minimum 350mm clearance from ceiling to top
mounting position.
3. Fix mounting brackets (1) to the wall with screw set (2 & 3).
Align slot in the top mounting bracket horizontally and
bottom mounting bracket vertically.
4. OPTIONAL FOR RETRO-FIT: Insert support (9) onto the
lower tube (5) if required to cover undesired mounting hole
from a previous installation. Install its mounting bracket
(18) to the wall accordingly.
4. Slide the clamp bracket (4) onto the lower tube (5) and
adjust it to the centre of the lower tuble.
5. Screw the lower tube (5) into top tube (6) through top
support (7) and tighten with screw (8) inside of the top
support. Connect diverter (10) to shower column.
6.Attach the shower column to the mounting brackets (1) and
tighten grub screws (11) to hold in place.
7. Fit O-ring (12) into groove in the base of elbow (13) and
then screw it to G1/2”B water supply nipple (not supplied)
until the back surface of the elbow touches the finished
wall. Ensure the outlet of the elbow faces down.
8. Connect water supply hose (600mm length) (14) to FRONT
INLET of the diverter and to the elbow (13).
9. Connect hand shower hose (1500mm length) (15) to BACK
OUTLET of the diverter and to hand shower (16).
10. Attach overhead shower (17) to the top tube.
NB: The shower can be operated in two modes, i.e. Hand Shower or Overhead Shower mode.
1. Ensure that all connections are tight.
2. Turn on the main water supply and check for leaks. Repair as needed.
3. Switch the diverter to Hand Shower mode.
4. Disconnect the hand shower from the shower hose and then turn on the shower mixer for mininum one
minute to flush any residual debris from the lines.
5. Check and clean filter washers as necessary. Reinstall the shower hose back to the hand shower and the
elbow.
6. Adjust the height of hand shower by sliding the clamp bracket up or down.
7. Switch the diverter to Overhead Shower mode.
8. Disconnect the overhead shower from the top tube and then turn on the shower mixer for minimum one
minute to flush any residual defris from the lines.
9. Check and clean filter washers as necessary. Reinstall the overhead shower back to the top tube.
Clean all finishes with mild soap and warm water. Wipe entire surface completely dry with a clean soft cloth.
Many cleaners may contain such chemicals as ammonia, chlorine, toilet chemials etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Englefield fittings.