Kohler MODERN LIFE K-77835T-1 Instruction Manual

MODERN LIFE
INSTALLATION INSTRUCTIONS
VANITY
K-77835T-1/-4/-8
-1-
·
·
·
·
·
Observe all local plumbing and building codes.
Prior to installation, unpack the new lavatory and inspect it
for damage. Return the lavatory to its protective carton
until you are ready to install it.
All information in these instructions are based the latest
product information available at the time of publication.
Kohler China reserves the right to make changes in
product characteristics, packaging, or availability at any
time without notice.
Fixture dimensions are nominal and conform to tolerances
established by ASME Standards (A112.19.2-2013).
The product complies with GB/T 6952-2015.
Make sure that the wall and floor are square
and plumb to ensure proper installation.
IMPORTANT:
·
·
·
·
·ASME (A112.19.2-
2013)
GB/T 6952-2015
ORDERING INFORMATION
Modern Life 600mm Vanity.................... K-77835T-1/-4/-8 600mm ......................... K-77835T-1/-4/-8
REQUIRED MATERIALS/
(NOT SUPPLIED)
TOOLS
·
·
·
·
·
·
·
Level
Drill with bit6mm
14mm wrench
Framing square
Channel lock pliers
Tape measure
Pencil
·
·
·
·
·
·
·
6mm
14mm
No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 528137
2 528137
8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA POST CODE: 256410
8 256410
©
©
Copyright Kohler China Investment Co., Ltd. 2018
2018
1269083-T01-B

-2-
Install the Basin
Note! The lavatory tops must be installed on a cabinet or
matching metal stand (refer to Installation and User Guide
packed with the cabinet or stand for installation details).
Recommend Kohler metal square leg or Kohler bathroom
furniture for support or decoration.
!
(
)
!
·
76mm
·Rough-in the supplies and the drain piping.
The supply stop handles cannot extend more than
76mm from the finish wall when in the open position.
NOTE:
Fig.#1
1
ROUGHING-IN DIMENSIONSROUGHING-IN DIMENSIONS
UNIT: mm
:
Kohler reserves the right to change marked dimensions without prior notice.
Reference Value
598
200 66
481
35
45
586
K-77835T-1
K-77835T-4
K-77835T-8
3- 35
592
356
481
598
200 66
Installation Side
80
181
102
3- 35
592
481
598
200
66
Installation Side
80
181
356
203
66
200
134
80
181
356
1269083-T01-B

-3-
·· Install the faucet and drain to the lavatory according to the
manufacture's instructions.
·
·
·
·
·Carefully place the lavatory against the wall, so the
hanger bolts extend through the lavatory holes.
·
·
·
Level the lavatory.
Install the cap nuts and washers, and tighten until snug.
Do not
overtighten the cap nuts.Overtightening may cause
damage to the product.
Clean the lavatory top.
CAUTION: Risk of product damage.
·
·Put the sealant around the back wall attached surface of
the lav evenly.
Apply Silicone sealant
along this face
Washer Nut
Offset Nut
Fig.#3
3
·
·
10mm
()
, 65-
75mm
1. 2 3
2.
·
·
Drill two 10mm hanger bolt holes at the marks on the wall.
The nylon anchors is needed for concrete wall (supplied).
Mount hanger bolts to the wall so approximately 65-75mm
of each bolt remains exposed.
1. Height dimensions marked in fig. 2 and fig. 3 could
be adjusted per your the vanity height or the actual
height of the console leg.
2. Other fastening devices of sufficient size and
strength may also be used.
NOTE:
Attachment
Bolt (x2)
Wall Plug
550mm
Waste
Outlet Waste
630mm
805mm
80mm
291.5mm
Fig.#2
2
1269083-T01-B

-4-
IMPORTANT CONSUMER INFORMATIONIMPORTANT CONSUMER INFORMATION
CARE AND CLEANING
To keep your lavatory looking new, make sure you rinse it out
thoroughly after each use. on this
product, as they will scratch and ruin the surface. Stubborn
stains, paint, or tar can be removed with turpentine or paint
thinner.
DO NOT USE ABRASIVES
Caution! Risk of product damage.
Many cleaners contain abrasive and chemical substances,
and should not be used for cleaning stainless steel, enamel,
plated or plastic fittings.
These finishes should be cleaned using a mild washing up
detergent or soap solution, rinsed and then wiped dry with a
soft clean cloth.
1. 1288760-0
4
2.
3.
4.
Install the Plumbing
1. Install drain 1288760-0 according to the manufacturer's
instructions. The two overflow pipes shall be fixed onto the
outlet valve. Fix the overflow head assembly vertically onto
the faucet supply pipe with plastic tie, as shown in Fig.4.
The overflow pipes can be fixed on either the right side or
the left side of the supply pipe and shall not interfere with
the lift rod. The height of the overflow head assembly will
affect the overflow level and can be adjusted if necessary.
please
lower the height of the overflow head.
Make sure a watertight seal exists on all
basin drain connections.
Provide access to the plumbing connections
for future plumbing maintenance.
2. Connect the hot and cold water supplies.
3. Open the hot and cold water valves, and check the supply
connections for leaks.
4. Run water into the basin, and check the drain connections
for leaks.
Caution!
Caution!
If the water level is too high to affect the overflow,
Fig.#4
4
Lift rod
Plastic Tie
Faucet Supply Pipe
Overflow Head Assembly
Overflow Pipe
Outlet Valve
1269083-T01-B