Kohler MEMOIRS 22559T-4V User manual

1372307-2A-A 1
1372307-2A-A 4
INSTALLATION INSTRUCTIONS
MEMOIRSMEMOIRS
SERVICE PARTS
**Color code must be specified when ordering.
22559T-4V Floor Mount Bath Filler With Handshower -Lever
22559T-3S Floor Mount Bath Filler With Handshower -Cross
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. Inspect the supply tubing for damage. Replace as necessary.
3. Observe local plumbing codes.
4. The minimum working pressure for the diverter is 0.05MPa(0.5bar).
5. Check for leaks before covering the pipes, repairs as needed.
6. The highest working pressure for handshower is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar), a pressure reducer is
needed. The highest water and environment temperature is 60ºC. Please keep handshower and shower arm away
from heater, or it may become damaged and cause injury to the user.
7. Please purchase the matched mounting base 97905T when install the faucet.
ROUGH-IN DIMENSIONS
*Please purchase the appropriate bathtub according to the dimension.
22559T-4V Floor Mount Bath Filler With Handshower -Lever
22559T-3S Floor Mount Bath Filler With Handshower -Cross
78125
834562**
3008523
834404
40933
22559T-4V:1391016**
832751
832751
22559T-4V:1391017**
832751
22559T-3S:1372650**
22559T-3S:1372651**
832751
78125
837206
837207
1093763**
77955
1372306
1082901
1010167
65218
1177225
835014**
835015
835018
835016
74463
1383661
1248781**
77420
77420
1030624
1240266
1297484**
G1/2˝
G1/2˝
1500
G1/2˝
28 28
240
250
256(For 22559T-4V)
265(For 22559T-3S)
43
742~762
110×110
*70 Min.
Bathtub
115
*221
*630 Max.
885~905
32726~746
998~1018
928~948
43
24.6º
22559T-4V
22559T-3S

1372307-2A-A 2
1372307-2A-A 3
9
10
10
14
11
12
13
11
How to Maintain the Handshower
Any debris or mineral build-up may cause the flow stream distorted or
reduce the flow rate. To remove the debris or mineral build-up, run
water through the handshower, firmly press or rub your finger back and
forth across the rubber nozzles.
INSTALLATION CHECKOUT
Ensure that all coupling nuts are tight. Ensure that the handles are in
the off position.
Turn on main water supply, and check for leaks. Repair as needed.
Remove the aerator(14) and handshower(10). Turn on faucet handle.
Run hot and cold water through spout for about one minute to remove
any debris. Remove and clean the screen washer. Check for leaks.
Remove any debris. Shut off the faucet. Reinstall the aerator and
handshower.
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
CLEANING INSTRUCTIONS
HANDLE OPERATION
Turn the left handle clockwise for hot water. Turn the right handle counter-clockwise for cold water.
Lift the diverter knob gently for handshower. Press the diverter knob back in the normal position for bath spout.
Press the buttons of the handshower to change the water flow.
INSTALLATION
How to Install the Faucet
Shut off water supply. Cut away the extending part of the base
protector(1) in accordance with the tile surface. Remove the plug(2)
from the base. Remove the protector(3) from the faucet.
Slide up the escutcheon kit(4). Install the faucet. NOTE: Keep the
faucet vertical to base, to avoid damaging the O-rings on the bottom.
Keep the spout pointing to tub. Fix the faucet to the base with the
screws(5) and washers(6) through the flange(7). Tighten the screws
with hex wrench(8).
Slide down the escutcheon kit, make sure it is against the finished floor.
How to Install the Handshower
If needed, install the restrictor(9) into the handshower(10). Put the
washers(11) into the hose(12). Connect the hose to the connector(13)
of the diverter kit and handshower. Tighten all the connections.
Hang the handshower on the bracket.
5
4
7
8
1
6
2
3